10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
3pcs L298N Motor Driver Module 4 Chaneel Motor Drive Smart Car Module
$41.54Driver ModuleAdd to cartDescriptionThe four channel L298N motor drive module integrates two L298N chips and can drive four DC motors to realize the control of forward and backward rotation and motor speed. The module is equipped with LM2596S step-down chip. If the motor with 7V voltage or more is driven, 5V power can be output to the control …
3pcs L298N Motor Driver Module 4 Chaneel Motor Drive Smart Car ModuleRead More
Geekcreit D1 Mini ESP32 ESP-32 WiFi+bluetooth internet of Things Development Board Based ESP8266 Module
$21.86Motherboard & Development BoardAdd to cartMore informations:https://github.com/LilyGO/ESP32-MINI-32-V2.0DescriptionThis is D1 Mini ESP32 ESP-32 WiFi+bluetooth Internet Of Things Development Board.Use exampleit can also match the next productPackage included4 x Long female pins4 x short female pins4 x Normal pins1 x mini D1 ESP32
AF1020 Dust-proof Probe Super-stable Pipe-type Current-type Temperature and Humidity Transmitter Temperature Senor Humidity Sensor
$176.16Solar CollectorsAdd to cartSpecificationModel:AF1020 Type Temperature and Humidity TransmitterTemperature measurement range:- 40 ~+80 (℃)Measurement accuracy:+-0.5 (℃)Working Voltage 15-36 (V)Humidity accuracy:+-3% RHHumidity measurement range:0-99.9% RHCurrent output:4-20 m AInstructions1. Power cord positive DC18~36V (red wire)2. Power ground wire GND (black wire)3. Humidity current output 4~20MA (yellow line)4. Temperature current output 4~20MA (white line)Installation sequence1. Connect the red, black, yellow and …
3Pcs 5M Meter thermometer Electronic Digital Display FY10 Embedded thermometer indoor and Outdoor Temperature Measurement
$20.72Test & Measuring ModuleAdd to cartFunction introductionOverall size:48*28*15mmInserted hole size:46*27mmLCD temperature display-50→ to 110→ temperature measurement, 0.1 degree resolution.C and F display versions are availableStandard 0.8m waterproof probeCable length:5 meterPackage includes3 x Thermometer
Peacefair PZEM-028 AC Digital Multifunction Meter Voltmeter Ammeter 0~100A/400V Power Factor Meter
$27.97Electronic Accessories & SuppliesAdd to cartError adjustmentThe product is 100% calibrated before leaving the factory, and the user can also manually adjust the error by himself. The method is as followsStep 1:Long press the button (about 3 seconds) until the digital digit on the screen flashes, then release the button;Step 2:Digital flashing means entering the error adjustment state, the digits …
3pcs 433MHz RF Wireless Receiver Module Transmitter kit + 2PCS RF Spring Antenna OPEN-SMART for Arduino – products that work with official for Arduino boards
$12.11Smart ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionThe kit includes one pair of transmitter and receiver modules and one pair of spring antennas for increasing the communication distance. And the frequency is 433MHz. It is very popular for remote …
10pcs DC 3.7-6V To 400KV Boost Step Up Power Module High Voltage Generator
$55.81Power Supply ModuleAdd to cartFeatureThe high-voltage module uses the principle Tesla coil is made of high-voltage pulse output voltage current, small size, high efficiency, simple external circuit(just plug in the switch, the battery can be) discharge intensity violent.SpecificationModel:MC-105Volume:Length 65mm Diameter 24mm, Diameter of cut surface 22mmVoltage:Input DC3.7-6V, output DC200-400KVCurrent:Input 4A, output 0.5ALength:Input 10 cm or so, the output is …
10pcs DC 3.7-6V To 400KV Boost Step Up Power Module High Voltage GeneratorRead More
Reviews
There are no reviews yet.