10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
2000PCS 1 Pin Header Connector Housing for Dupont Wire Jumper Compact
$31.63Electronic Accessories & SuppliesAdd to cartFeatures2.54mm Single-row strip Dupont Wire Jumper.Professional and compact, light weight.Material:PlasticSize:14 x 2.5mm/ 0.55 x 0.1inch (L x W)Color:BlackPackage includes2000 x 1Pin Header Connector
HIFI 2.0 Stereo bluetooth 5.0 Lossless Decoding 27W*2 Digital Class D Car Speaker Audio Power Amplifier Board
$8.73Amplifier BoardAdd to cartDescriptionAVN-302 is a low EMI, no filter, Class D Bluetooth audio decoding power amplifier, with an internal protection mechanism for overcurrent, undervoltage, short circuit and overheating automatic shutdown.SpecificationModel:AVN-302Power:7.4V-14.4VSize:55*50mmOutput power:27W*2Boot instructions1. Insert the U disk, load the file (reading completed) automatically enter the playback, the red indicator flashes2. In the playback state, short press the ‘P/P’ …
CJMCU-1286 PIC16F1823 Microcontroller Development Board
$8.73Motherboard & Development BoardAdd to cartDescriptionCJMCU-1286 is a PIC microcontroller minimum system, running stability and high reliability,internal resources are relatively small, so the microcontroller is simple and convenient to use.The operating voltage is 1.8V – 5.5V.Package included1 x CJMCU-1286 PIC16F1823 Microcontroller Development Board
4Pcs 7-Segment 0.56 inch 4 Digit 12 Pins Red LED Display
$8.38Display ScreenAdd to cart4Pcs 7-Segment 0.56 Inch 4 Digit 12 Pins Red LED DisplayDescriptionWith time displayCommon anodePin Number:12 pinsDigit Number:4 digitsDigit Height:0.56 inch / 1.4 cmSize (L x W ):2 x 0.75 inch / 5 x 1.9 cmColor:RedPackage included4 x 0.56’inch 4 Digit LED Display
3pcs M5Stack StickC Pro to Plus Hat Prototype Diy Protoboard Breadboard PCB Universal Board
$31.71Expansion Board & ShieldAdd to cartProduct FeaturesHole Size:0.039inch 1mm (CNC Drilled)Hole Pitch:0.1 in – (2.54 mm)Entire Hole Quantity:168 HolesPackage Included3 x PRO TO PLUS HAT3 x 8 pin header ( 90° )
Reviews
There are no reviews yet.