10Pcs inverter Boost High Voltage Generator 15KV High Frequency Transformer
$55.49
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformers in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150Ω ~ 1.5KΩ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
10 x High Voltage Generator Kit
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.18 kg |
---|
Customers Also Viewed
Excellway 11Pcs Terminal Removal Tool Kit Wiring Connector Pin Release Extractor
$14.16ConnectorsAdd to cart11pcs Terminal Removal Tool Kit Wiring connector Pin Release Extractor PullerBrand:Excellway®Color:BlackMaterial:AluminumFeature1.This kit set is designed to remove car wire terminals without damage.2.Please don’t Pry the terminals with this kit, Just push and pull the terminal pins.Packing Included1x 11pcs/set Wire Terminal Removal Tool
20pcs 0.36 inch DC0V-32V Blue LED Digital Display Voltage Meter Voltmeter Reverse Connection Protection
$67.74Test & Measuring ModuleAdd to cartFeature∵ Super high precision∵ Ultra-low startup voltage, red minimum 2.5V, green minimum 2.7V, blue minimum 3.0V. When the power supply voltage is lower than 3.5V, only the brightness is lowered, but the measurement accuracy is not affected.∵ With reverse connection protection, it will not burn.Measuring range:0.00V-32.0VPower supply range:Red DC2.50-32.0V, green DC2.70-32.0V, blue DC3.00-30.0VHighest input:DC32.0V. Note:If …
10Pcs 100mm OD 12mm 3mm Thick Wall Borosilicate Glass Blowing Tube
$30.36Lab TubesAdd to cartProduct DescriptionHigh quality borosilicate glass, Premium borosilicate tubing, preferred by scientific and artistic glassblowers world-wide. HEAVY wall tubing 10 pieces, 12mm outside diameter with a 3mm wall – all approximately 100mm long. This glass tube bends easily with propane (LPG) and oxygen mix. Brand new, high quality, heat and corrosion resistant. SpecificationName:10Pcs 100mm OD 12mm …
10Pcs 100mm OD 12mm 3mm Thick Wall Borosilicate Glass Blowing TubeRead More
VHM-306 TPA3118 2x30W 12-26V DC Stereo Audio bluetooth 4.2 Digital Power Amplifier Board for Amplifiers D3-001
$16.83Amplifier BoardAdd to cartSpecificationsModel:VHM-306 Audio input:DC12~36V Power amplifier chip:TPA3118 Bluetooth channel:stereo Output Power:30W*2Applicable impedance:4,6,8Ω AUX input:3.5 earphone holder Product Size:70*52*12mm Package Included1 x VHM-306 TPA3118 2x30W Bluetooth 4.2 Digital Amplifier Board
10pcs XD-M131 DC 12V Photosensitive Resistor Module Light Control Switch Photosensitive Relay Module
$49.09Relay ModuleAdd to cartSpecificationProduct model:XD-M131Product Name:photosensitive relay moduleOperating voltage:12VOutput mode:one channel relayOverall size:52 x 31 x 31mmDescription1. This product is mainly used for light detection, brightness detection and control and other occasions, through the potentiometer can be adjusted to detect brightness threshold. With the relay, it can do a variety of brightness detection switch, you can control a …
5pcs 1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial Port
$54.01Display ScreenAdd to cartFeatureResolution:128X160Driver IC:ILI9163/ST7735Module with regulator IC supports 3.2V/5V power supplyWith SD card holder, you can do experiments like digital photo frameThe module reserves the Nokia3310/5110 interface, supports the 1602 interface, and directly plugs in and out.IO for streamlined wiring:(only 3 IOs after optimization)1. RST– directly connected to the microcontroller reset signal terminal, this IO can save2. …
5pcs 1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial PortRead More
Reviews
There are no reviews yet.