inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
Shipping:Standard Shipping about 10-25 business days
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
1 x High Voltage Generator
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Customers Also Viewed
500mL Mini Scuba Diving Equipment Portable Oxygen Cylinder Backup Air Oxygen Tank$319.94Solar CollectorsAdd to cart
SpecificationsName:0.5L Portable Mini Oxygen CylinderAir Oxygen Tank Breath DivingBreathing Oxygen CylinderCapacity:0.5LMaterial:Aviation aluminumOxygen cylinder weight:1040gOxygen cylinder dimension:φ6*35.5cm (2.4*14inch)Air capacity:3.0 Cu.Ft / 85 LittersMax. pressure:3000PSI / 200bar / 20MPaMax. dwell time underwater:10minNumber of underwater max. breathing:21 times(depending on individual lung capacity and depth of diving)Aqualung Rotary Union–Size:6*2.5*14cm(2.4*1*5.5inch)–Color:Black–Function:Connect the respirator and the large bottle of oxygen cylinder, and …
500mL Mini Scuba Diving Equipment Portable Oxygen Cylinder Backup Air Oxygen TankRead More
3pcs DC-DC Boost Step Up Module 2.5V-5.5V input 5V/2A Output$12.88Power Supply ModuleAdd to cart
FeaturesHigh performance synchronous rectification ICWith temperature protection, overcurrent protection, short circuit protection, low voltage low current output protection functionInput:2.5V (MIN) ~ 5.5V (MAX)Output:5V / 2A ± 5% (MAX) support 1.5A long-distance runningEfficiency:92%Product size:L42mm * W15mm * H5mmWorking temperature:-40→ ~ 85→Storage temperature:-55→ ~ 150→Switching frequency:1MHZStatic power consumption:80uAWork indication:Blue LED on when output is 5VApplication:to charge mobile …
3pcs DC-DC Boost Step Up Module 2.5V-5.5V input 5V/2A OutputRead More
5Pcs 7x9cm PCB Prototyping Printed Circuit Board Prototype Breadboard$6.10Electronic Accessories & SuppliesAdd to cart
5Pcs 7x9cm PCB Prototyping Printed Circuit Board Prototype BreadboardDescriptionMaterial:BakeliteEach measures 7 x 9cm with 720 through holes (0.1 inch industrial standard spacing) for mounting componentsReferencing numbers printed on both sides for easy reference of individual holesSpecificationDimension:7 x 9cmThickness:1.5mmHole pitch:2.54mmHole inner diameter:1.0mmPackage included5 x PCB Printed Circuit Experimental Board
15S 48V Lithium Battery 3.2V Power Protection Board 15A-180A with Temperature Protection Equalization Function Overcurrent Protection BMS PCB$34.95Battery Protection ModuleAdd to cart
Current 15A / Current 20A / Current 30A / Current 40A / Current 50A / Current 60A / Current 70A / Current 100A / Current 150A / Current 180A / Current 130A /
71 2 Megapixel Cam Module UVC Fixed Focus IMX291 Sensor USB Mini Cmos Camera Module Support Microphone$94.03Other Module BoardAdd to cart
>>>Manual:Click here to openSpecificationsModel No.:HBVCAM-1917HDModel Size:38mm ≠ 38mm ≠ 37.7mm÷0.5MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:FixedObject distance:30CM-infinityResolution:600LW/PH (Center)PCB printing ink:Blackinterface:USB 2.0Power supply:USB bus powersupply voltage:DC 5V÷5%Maximum Power consumption:1000 mWOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvc Sensor:IMX291 (1/2.8” )Seneor Package:CSP,Bare DieMaximum resolution:1920*1080Sensitivity:3300mv /(lux-sec)Pixel Size:2.9m x 2.9┢m Maximum Image …
71 2 Megapixel Cam Module UVC Fixed Focus IMX291 Sensor USB Mini Cmos Camera Module Support MicrophoneRead More
3pcs 433MHz RF Wireless Receiver Module Transmitter kit + 2PCS RF Spring Antenna OPEN-SMART for Arduino – products that work with official for Arduino boards$12.11Smart ModuleAdd to cart
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionThe kit includes one pair of transmitter and receiver modules and one pair of spring antennas for increasing the communication distance. And the frequency is 433MHz. It is very popular for remote …
3pcs 433MHz RF Wireless Receiver Module Transmitter kit + 2PCS RF Spring Antenna OPEN-SMART for Arduino – products that work with official for Arduino boardsRead More
LM399 Voltage Reference 2.5V/5V/7.5V/10V High Precision Reference Source$52.77RF amplifierAdd to cart
SpecificationInput voltage:+15VOutput voltage:+10V/+7.5V/+5V/+2.5VAccuracy:0.00001Chip temperature drift:0.5ppm/→Size:5*5cmJumper cap connection:Output voltageShort J5 to J6:5VShort J7 to J8Short J1 to J2:10VShort J3 to J4Short J5 to J6Short J3 to J4:7.5VShort J5 to J6Short J7 to J8Short J5 to J6:2.5VShort J7 to J8Short J11 to J12Short J5 to J6:6VShort J7 to J8Short J1 to J2Short J5 to J6:4VShort J7 to …
LM399 Voltage Reference 2.5V/5V/7.5V/10V High Precision Reference SourceRead More
There are no reviews yet.