inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
DC 0-300V 500A Voltage Current Panel Meter Digital Blue Red Dual LED Voltmeter Ammeter with 500A/75mV Shunt
$48.10Electronic Accessories & SuppliesAdd to cartFeatures-2 in 1 function Voltmeter Ammeter, Easy install.-This meter test of Voltages and Amps, power supply can taken from the test circle, no additional power supply-Power supply DC 4.5V – 30V range (Attention:The maximum of input voltage cannot be exceed of 30V, otherwise would be burnt)-Display Range:DC 0V – 300V 0-500A (Please don’t exceed the …
3Pcs AC 220V 50A Power Amplifier Filter Power Supply Eliminate DC Power Filters for Toroidal Transformer
$28.05Module ComponentsAdd to cartProduct DescriptionThis product is connected in series with AC220V live wire. A 50A high-current rectifier bridge is used in series to eliminate the DC component more thoroughly.It can effectively eliminate the abnormal noise of the transformer caused by the DC component in the power grid (especially the sound of the toroidal transformer).Size:65MMX60MMx28MMType:Plug-in typePackage included3Pcs Filter …
5V WiFi Remote Garage Door Opener Controller Work with Alexa & IFTTT Google home Wireless Remote Control Switch
$21.86Smart ModuleAdd to cartNew toy for makers who want to build their own smart home system OverviewThe wireless switch supports inching /self-locking mode. You can add the device to the APP eWeLink to remote control connected home appliances or devices. In self-locking mode, you can remote turn on/off connected devices immediately. When in inching mode, you have two …
10pcs 3.7V 9V 5V 2A Adjustable Step Up 18650 Lithium Battery Charging Discharge integrated Module
$20.24Boost & Buck ModuleAdd to cartFeatureInput voltage:4.5-8VOutput voltage:continuous adjustable 4.3-27V (Counter clockwise to boost voltage)Charging voltage:4.2V Charging current:up to 1ADischarge current:the maximum 2AOutput reference maximum current:5V 1.4A, 9V 0.8A, 12V 0.6AQuiescent current:about 0.5 mAOvershoot protection:YesOver discharge protection:None (also can be said yes, because 2V cut-off boost but does not block the output, output has 2V)Deadline boost:2V, depending on whether added …
Reviews
There are no reviews yet.