inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
5Pcs MQ-7 MQ7 Carbon Monoxide CO Gas Sensor Detection Module
$13.49Sensor & Detector ModuleAdd to cart>>>Manual:Click here to openOverviewSensitive material MQ-7 gas sensors used in clean air, low conductivity tin oxide (SnO2). High-low temperature cycling detection mode (1.5V heating) carbon monoxide detector, conductivity sensor with the increasing concentration of carbon monoxide gas in the air increases,high-temperature (5.0V heating) cleaning cryoadsorption stray gases. Using a simple circuit to change the conductivity, …
5Pcs MQ-7 MQ7 Carbon Monoxide CO Gas Sensor Detection ModuleRead More
Mini DC12V 3M Micro Quiet Motor Submersible Brushless Water Pump
$24.29Electrical Pump & ValveAdd to cartDescriptionMini DC 12V 3M 240L/H Micro Quiet Brushless Motor Submersible Water PumpFeatureBrushless, permanent magnetic rotor, maintenance-free.Stator and circuit board sealed by epoxy resin.The axis is enclosed with static sealing, which can avoid leaking problemsAdopt high performance stainless steel shaft.Amphibious design, able to work either on land or in water.Super long working life (more than 30,000 …
Mini DC12V 3M Micro Quiet Motor Submersible Brushless Water PumpRead More
100-240V Power Adapter Power Supply Adaptor Plugs AU Standard
$16.19AC/DC AdaptersAdd to cartPower Supply Adaptor for Makita Radio BMR100 BMR100W BMR102 BMR105 DMR105SpecificationsInput:AC 100-240V, 50/60HzOutput:DC 12V 1AColor:BlackSize(Approximately):7.8*4.9*3.2cm(approx.)Wire length(Approximately):93cmPlug type:AU PlugFeatures-Voltage Protection-Short Circuit Protection-Current Protection-Sealed for protection against moisture and humidityApplicationFor Makita Radio BMR100 BMR100W BMR102 BMR105 DMR105Package included1 x Adaptor
3pcs BT201 Dual Mode 5.0 Bluetooth Lossless Audio Power Amplifier Board Module TF Card U Disk Ble Spp Serial Port Transparent
$16.31Amplifier BoardAdd to cart>>>Manual:Click here to openOverviewBT201 5.0 Bluetooth module is a 4-in-1 single chip that supports bluetooth, usb flash drive and TF card. The highlight of the chip is that it supports lossless music playback, simple and clear serial port control function, BLE pass-through function and SPP pass-through function.It greatly reduces the development difficulty of embedded bluetooth …
100pcs 30pF 5.08MM 50V Multilayer Monolithic Ceramic Capacitor
$5.09Electronic Accessories & SuppliesAdd to cartDescriptionFrequency characteristics:low frequencyAdjustment method:fixedLead Type:Radial Lead WireTolerance:÷ 10 (%)Pressure resistance:50 (V)Capacity:30pFFeaturesLarge capacity, small size, high reliability,Stable capacity, high temperature and humidity resistance.Applications:Widely used in electronic precision instruments.A variety of small electronic equipment for resonance, wave filtering Package included100 x 30pF capacitor
220V 750W Stainless Steel Deep Well Submersible Screw Pump Water Pump
$546.74Electrical Pump & ValveAdd to cartSpecificationsName:Submersible PumpColor:grayMaterials:stainless steelPower:750WVoltage:220VSize:540*100mmCord Length:18mPump Head/Lift:75m MaxFeatures-Energy-efficient, easy to install, low energy, low noise.-Stainless steel body, strong and durable, not easy to rust.-Stainless steel filter prevents impurities from entering the pump and has a long service life.Package Included1 x Submersible Pump3 x Accessories(distribute the adapter according to your country)
20Pcs Mini DC-DC1.3A Voltage Converter Step Down Module 12V 24V to 5V 3.3V 9V with integrated inductor for 360 RC
$31.43Power Supply ModuleAdd to cartFeaturesThe maximum output current is 1.3A, and it is running within 1A for a long time;Non-isolated DC synchronous rectification with up to 94% conversion efficiencyOne-piece inductor, lower heat than ordinary shielded inductorUniversal, optional output voltage, spot welding directly on the boardOutput with LED indicator for easy and visual indication of voltage outputWith enable (EN) port, …
65x37mm Universal Slotted Frame Rail Floor Jack Guard Adapter Lift Rubber Pad Rubber Mat
$22.67RubbersAdd to cartDescriptionThis rubber pad is suitable for car Jack with 55mm intake.SpecificationType:Rubber Pad Universal Diameter 65×37 With Wide V-GrooveMaterial:RubberColor:BlackDiameter:65mmTotal height:37 mmGroove Top:15mmGroove Bottom:10mmGroove Height:8mmFeatures1. Universally applicable.2. Industrial Quality.3. Very robust (min. 80 Shore).4. Easy install and durable use.5. Great quality and great Fitment.6. Direct Replacement, No Modifications Necessary.FitmentSuitable For Car Jack With 55mm IntakePackage Included1 x …
65x37mm Universal Slotted Frame Rail Floor Jack Guard Adapter Lift Rubber Pad Rubber MatRead More
Reviews
There are no reviews yet.