inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
MK1 Acrylic Remote Ver. Tony DIY Arc Reactor Lamp Kit Remote Control Illuminant LED Flash Light Heart Set
$70.86Engraving Parts & AccessoriesAdd to cartThe diaplay box and the bracket inchPROOF THAT TONY STARK HAS A HEARTinch is sold separately, please click that:ID:1429112The following chart shows different versions of our ARC reactor DIY model lamp, you can choose your favorite ones.ARC Reactor DIY Model Lamp Version:Please refer toMK1 Acrylic Frame Version:ID:1420733MK1 Aluminum Alloy Frame Version:ID:1434480MK2 Acrylic Frame Version:ID:1434467MK2 Stainless …
5pcs DC Motor Driver Board 2 Way DRV8833 Motor Drive Module DC 3-10V
$10.17Driver ModuleAdd to cartParametersSize:18.5 x 16 mmInput voltage:3-10VSingle H bridge output current:1.5A, can drive 2 dc deceleration motors.Built-in overcurrent protection, short circuit protection, undervoltage latching and overheating protection. Sleep mode with low power consumption.Purpose:drive dc motor and 4-wire stepping motor up to 1.5A.InstructionsULT low level is in sleep mode (need to disconnect J2 short welding spot behind the …
5pcs DC Motor Driver Board 2 Way DRV8833 Motor Drive Module DC 3-10VRead More
M5Stack ESP32 Open Source Faces Pocket Computer with Keyboard/Gameboy/Calculator Development Board
$177.66Smart ModuleAdd to cartIntroductionFACES Kit is a feast of functional panels, contains the most commonly used panels and keyboards with MEGA328 processor inside, communication protocol through IIC(0x08) as slave mode. With these 3 different panels, it will be very easy to support keyboard interaction with your M5Core.If you up for some classic video game, PyGamer panel plus M5Core …
10pcs 1S 3.7V 4A li-ion BMS PCM 18650 Battery Protection Board PCB for 18650 lithium Battery Double MOS
$13.12Battery Protection ModuleAdd to cartSpecificationsOvercharge detection voltage:4.25 ± 0.05VOvercharge release voltage:4.23 ± 0.05VOver discharge detection voltage:2.45 ± 0.1VUpper limit continuous current:4AOvercurrent detection current:5ACharging voltage:4.2VProduct Size:35 * 4 * 2.2MMIC components:DW01 + 8205A * 2 The main function:Overcharge protection, over discharge protection, short circuit protection, overcurrent protection.Wiring InstructionsB +:Connected to the battery positive.B-:Connected battery negative.P +:For the battery pack output …
CBB61 3Pcs 1.2UF Starting Capacitance 450V AC Fan Capacitor CBB Motor Run Capacitor
$4.04Module ComponentsAdd to cartFeatures1.Use polypropylene film with excellent electrical properties as the medium, and vaporize the metallized layer as the electrode under high vacuum conditions; 2.Use High-quality epoxy resin potting material is filled and sealed; the product has stable capacity, low loss, high pressure resistance, and good self-healing.3.Application:air conditioners, refrigerators, washing machines, electric fans, ovens, etc.SpecificationModel:CBB61Shell Material:ABSLine length:10cmShell …
CBB61 3Pcs 1.2UF Starting Capacitance 450V AC Fan Capacitor CBB Motor Run CapacitorRead More
Solar Charge Controller 15A LCD Display Controller Solar Controller for PWM Solar Power Panel Water Pump
$76.94Solar ControllersAdd to cart15A Controller For PWM Solar Panel Water PumpSpecificationMaterial:Acrylonitrile Butadiene Styrene (ABS)Color:BlackSize:14x9x3cmSystem voltage:12N/24V adaptiveUSB output:5V/2ACharging current:15ACharging voltage:13.7VRelease point cutoff voltage:10.7VWorking temperature:-20~+60°CFeaturesLCD displayPWM battery chargingAll necessary protections equippedAdjustable cotrolling parameter of the systemBuild-in industrial micro controllerBuild-in short-circuit protection, open-circuit protection, reverse protection,Over-load protection.Dual mosfet reverse current protection,low heat production.Application:Solar ControllerPackage include1 x solar controller
3pcs 5-30V 10A Wide Voltage Trigger Delay Relay Module Timer Module 2 Trigger Modes
$12.31Relay ModuleAdd to cartDescriptionTime can be adjusted by a potentiometer to meet the use of most of your occasions.With Micro USB 5.0V power supply input, it is very convenient to use.5-30V ultra wide power supply voltage.Two trigger modes:external trigger and onboard buttons trigger.It has a relay suction indicator.Strong anti-interference ability, all kinds of interference under the relay will …
3pcs 5-30V 10A Wide Voltage Trigger Delay Relay Module Timer Module 2 Trigger ModesRead More
Reviews
There are no reviews yet.