inverter Boost High Voltage Generator 15KV High Frequency Transformer Arc Ignition Igniter Coil
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Use
School science experiment, electronic equipment, negative ion generator, small scientific production and so on.
Feature
This circuit works to produce a stable high-frequency arc, the temperature is extremely high, can easily ignite the combustible, so it was called a plasma lighter.
Note
This transformer high voltage winding in the inner layer, is the segment skeleton wound, low voltage winding in the outer layer, please do not mistaken for this transformer is high voltage winding and low voltage winding the same way.
The transformer has two primary winding, one of the main group is coarse copper wire, a group of fine copper wire for the feedback winding. The secondary output is high voltage.
Transformer in a coarse and a thin winding together two copper wire is positive, respectively, the main winding tail and feedback winding head, connect the power supply positive.
Before soldering the transformer, the soldering part of the enameled wire head of the paint need to gently scraping with blade and then soldering, please note.
Precautions for product use
1. After the successful production, the transformer must be sealed with epoxy resin or insulating wax to be used for a long time. The air-borne work in the air will cause the coil to break through damage due to the lack of air insulation.
2. The input voltage of the kit is 3.7v. That is, a section 18650 battery voltage, if you need to increase the input voltage (maximum increase to 12V), you need to increase the feedback resistor resistance (we default send 120 ohm), otherwise the transistor is easy to burn. Feedback resistance increased to 150┯ ~ 1.5K┯ or so, the resistance should be adjusted from large to small, do not too small, otherwise will burn transistor or transformer, and should not be too large, too much will impact the output or make the transistor work in the non-switch state to make the fever is serious hot.
transformer design for the 15KV maximum output, which is 1.5 cm arc, the higher the output voltage is likely to damage the transformer. For reliable long-term continuous work, it is recommended to use insulating wax or epoxy resin to completely seal it, prohibit no-load working when no sealed.
Specification
Input voltage:3.7V-4.2V
Current
Output voltage
Output current
High pressure two-stage ignition distance
Size is about:27 x 16 x 21mm (Manual measurement, please understand the error)
Package includes
1 x High Voltage Generator
Schematic diagram
In order to prevent the output 2-line distance too far, resulting in no-load, you can solder a pin in the output, and put the end of the needle into the arc, is conducive to the discharge arc, lik the following show
After the success of the production, if the output terminal connected to a high-voltage capacitor and three high voltage rectifier composed of voltage doubling circuit, can produce DC high voltage, can produce anion generator, the wiring diagram is as follows:
Weight | 0.018 kg |
---|
Customers Also Viewed
5pcs TS-300B Turbidity Sensor Detection Module Water Quality Tester Washing Machine Turbidity Transduce
$43.93Sensor & Detector ModuleAdd to cartPrincipleTurbidity sensor TS-300B measures the turbidity (counter of suspended matter) in the wash water. Based on the optical principle, the sensor uses the light-emitting diode and phototransistor to receive the specific wavelength to measure the opacity or other substances of dirty water. concentration. By using phototransistors and light-emitting diodes, the light emitted by the sensor …
3Pcs USB Fan Speed Controller Module Reducing Noise Multi-stall Adjustment Governor DC 4-12V
$20.74Motor PWM Speed ControllerAdd to cartFeatures– USB Fan Air Conditioner – Strong winds and weak wind adjust freely – Stepless Speed Regulation – Suitable for the very common 5.0V USB fan on the market Regulation PrincipleThe non-adjustable fan is a 5V direct fan motor,while the two-stall fan is the interior has a step-up circuit board,when placed in the second gear,the …
5pcs JDY-08 BLE bluetooth 4.0 Serial Port Wireless Module Low Power Master-slave Support Airsync i Beacon
$45.12Smart ModuleAdd to cartFeaturesJDY-08 transparent transmission module is based on bluetooth 4.0 protocol standard, working frequency range is 2.4GHZ range, modulation mode is GFSK, large transmission power is 0db, large transmission distance is 80 meters, TICC2541 chip design is adopted, and users can modify device name by AT command. , service UUID, transmit power, pairing password and other …
ADC Module ADS1100 for Analog Signal Capture Converter Compatible M5StickC ESP32 Mini IoT Development Board Fi
$14.74Converter BoardAdd to cartnull Description ADC_HAT is another type of C-HAT specifically design for M5StickC controller. Same as ADC unit, this is an ADC converter component for stickc. Packed with an ADC converter chip ADS1100, which is a fully differential, 16-bit, self-calibrating, A/D converter. Extremely easy to design with and configure, the ADS1100 allows you to obtain precise …
5pcs Mini MP1584EN DC-DC BUCK Adjustable Step Down Module 4.5V-28V input 0.8V-20V Output
$8.94Power Supply ModuleAdd to cartSpecificationsModel:MP1584Name:DC-DC step-down moduleInput Voltage:4.5V ~ 28VOutput voltage:0.8V ~ 20VOutput Current:3A (Max)Conversion efficiency:96% (maximum)Output RippleSwitching frequency:1.5MHz (highest) typically 1MHzOperating Temperature:-45°C ~ +85°CSize:22mm * 17mm (L * W )Application areas:DIY mobile power, monitor power supply, power buggies, camera power supply, car power, communications equipment supply,etc.Packge included5 x Step Down Module
LILYGO TTGO T-Koala ESP32 WiFi and bluetooth Module 4MB Development Board Based on ESP32-WROOM-32 Micro USB
$26.23Smart ModuleAdd to cartFeatureEspressif official ESP32-WROOM-32 moduleLatest ESP32 version:REV14MB FLASHLithium battery interface, 500mA maximum charging currentCompatible with , MicroPythonDefault firmware:latest MicroPythoTechnical specificationsMicrocontroller:ESP-32Board power supply:(USB) 5VSupport battery:Lipo Battery 3.7VWorking voltage:3.3VFlash:4 MbytesLength:78 mmWidth:27 mmWeight:7.8 gramsPackage includes1 x ESP32 WiFi&bluetooth Broad2 x Pin
Reviews
There are no reviews yet.