Flame Flare Detection Module Flame Sensor 12V Relay Board infrared Receiver Module
$7.11
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Usage
Various flames, fire source detection, relay output, can be connected to 220V high current equipment
Features
1. It can detect flame or light source with wavelength in the range of 760 nm to 1100 nm. The flame distance of the lighter is 80 cm. The larger the flame, the farther the test distance is.
2. The detection angle is about 60 degrees, especially sensitive to the flame spectrum
3. The sensitivity is adjustable (blue digital potentiometer adjustment in the figure)
4. The comparator output directly triggers the relay
5. The external dimensions:50x26x19mm, with fixed bolt holes for easy installation
6. The output has a blue terminal block, convenient wiring
Electrical parameters
Supply voltage:12VDC
Current:greater than 150mA
Load:250V 10A AC or 30V 10A DC
Instructions for use
1. The flame sensor is most sensitive to the flame and also responds to the sunlight. It is generally used for flame alarms and other purposes.
2. By adjusting the potentiometer, the intensity of the sensor’s induced flame can be set. When the flame exceeds the set threshold, the relay is closed, the common end is connected to the normally open end, and when the flame is lower than the set threshold, the relay is disconnected. The common end is connected to the normally closed end;
3. The common end, normally open, normally closed three ports are equivalent to a dual control switch, when the relay coil is powered, the common end is open to the normally open end, when there is no electricity, the common end and the normally closed end are turned on;
4. The sensor and the flame should be kept at a certain distance to avoid damage to the sensor at high temperature. The flame distance of the lighter is 80cm. The larger the flame, the farther the test distance is.
Package includes
1 x Flame sensor module
Weight | 0.017 kg |
---|
Customers Also Viewed
Excellway 11Pcs Terminal Removal Tool Kit Wiring Connector Pin Release Extractor
$14.16ConnectorsAdd to cart11pcs Terminal Removal Tool Kit Wiring connector Pin Release Extractor PullerBrand:Excellway®Color:BlackMaterial:AluminumFeature1.This kit set is designed to remove car wire terminals without damage.2.Please don’t Pry the terminals with this kit, Just push and pull the terminal pins.Packing Included1x 11pcs/set Wire Terminal Removal Tool
20pcs 0.36 inch DC0V-32V Blue LED Digital Display Voltage Meter Voltmeter Reverse Connection Protection
$67.74Test & Measuring ModuleAdd to cartFeature∵ Super high precision∵ Ultra-low startup voltage, red minimum 2.5V, green minimum 2.7V, blue minimum 3.0V. When the power supply voltage is lower than 3.5V, only the brightness is lowered, but the measurement accuracy is not affected.∵ With reverse connection protection, it will not burn.Measuring range:0.00V-32.0VPower supply range:Red DC2.50-32.0V, green DC2.70-32.0V, blue DC3.00-30.0VHighest input:DC32.0V. Note:If …
10Pcs 100mm OD 12mm 3mm Thick Wall Borosilicate Glass Blowing Tube
$30.36Lab TubesAdd to cartProduct DescriptionHigh quality borosilicate glass, Premium borosilicate tubing, preferred by scientific and artistic glassblowers world-wide. HEAVY wall tubing 10 pieces, 12mm outside diameter with a 3mm wall – all approximately 100mm long. This glass tube bends easily with propane (LPG) and oxygen mix. Brand new, high quality, heat and corrosion resistant. SpecificationName:10Pcs 100mm OD 12mm …
10Pcs 100mm OD 12mm 3mm Thick Wall Borosilicate Glass Blowing TubeRead More
VHM-306 TPA3118 2x30W 12-26V DC Stereo Audio bluetooth 4.2 Digital Power Amplifier Board for Amplifiers D3-001
$16.83Amplifier BoardAdd to cartSpecificationsModel:VHM-306 Audio input:DC12~36V Power amplifier chip:TPA3118 Bluetooth channel:stereo Output Power:30W*2Applicable impedance:4,6,8Ω AUX input:3.5 earphone holder Product Size:70*52*12mm Package Included1 x VHM-306 TPA3118 2x30W Bluetooth 4.2 Digital Amplifier Board
10pcs XD-M131 DC 12V Photosensitive Resistor Module Light Control Switch Photosensitive Relay Module
$49.09Relay ModuleAdd to cartSpecificationProduct model:XD-M131Product Name:photosensitive relay moduleOperating voltage:12VOutput mode:one channel relayOverall size:52 x 31 x 31mmDescription1. This product is mainly used for light detection, brightness detection and control and other occasions, through the potentiometer can be adjusted to detect brightness threshold. With the relay, it can do a variety of brightness detection switch, you can control a …
5pcs 1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial Port
$54.01Display ScreenAdd to cartFeatureResolution:128X160Driver IC:ILI9163/ST7735Module with regulator IC supports 3.2V/5V power supplyWith SD card holder, you can do experiments like digital photo frameThe module reserves the Nokia3310/5110 interface, supports the 1602 interface, and directly plugs in and out.IO for streamlined wiring:(only 3 IOs after optimization)1. RST– directly connected to the microcontroller reset signal terminal, this IO can save2. …
5pcs 1.8 inch LCD TFT Display Module with PCB Backplane 128X160 SPI Serial PortRead More
Reviews
There are no reviews yet.