2000W High Power Soft Start Board 30A Dual Temperature Control Switch Delayed Start Board for Amplifier Amp DIY
$38.31
Type #1 / Type #2 / Type #3 / Type #4 / Type #5 / Type #6 /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Type(option)
1:Terminal type Songchuan relay
2:Plug-in terminal type Songchuan relay
3:Plug-in terminal Songle relay
4:Terminal Type Songle Relay
5:Terminal type HF-105F-1 Relay
6:Plug-in terminal type HF-105F-1 Relay
Product description
Dual temperature control soft start uses high quality power module to replace traditional transformer, with low energy consumption, high efficiency, ultra stable, low heat, 105-235V wide voltage (for domestic and foreign), and so on!
This product PCB adopts 1.6MM thick double-sided fiberglass board, 2.0 oz copper thickness, tin-spraying process to ensure good passing of high current.
It is suitable for high-power amplifier and post-stage power supply as delay soft start board to avoid high current impact at the moment of booting and better protect your machine.
HF-105F-1 high current 30A power relay, stable and reliable performance, the maximum power can support 2000W.
Features
1. Delay start, the first relay is connected at the moment of power-on, and then the current is limited by the NTC thermistor. After a delay, the main relay is turned on to realize the soft-start function. Suppress the inrush current of the power amplifier, because the power of the class A and high power amplifier transformer is large, the load impedance is extremely low, and the capacity of the power supply filter capacitor is too large, resulting in excessive current of the power amplifier when the power is turned on, which easily damages the rectifier bridge and the damage filter capacitor.
2. 2 way overheat protection, use the attached 75 degree temperature control switch to install on the radiator,
When the temperature of the power amplifier board heat sink exceeds 75 degrees, the board can immediately cut off the power supply, and the power amplifier will not be overheated and burned. Until the temperature of the heat sink drops below 75 degrees, the power amplifier can be turned back on, otherwise the power amplifier can’t be turned on.
3. The power switch uses a tact switch, which is convenient and flexible. To prevent frequent machine damage to the machine.After the soft start is turned on, it takes about 12 seconds to shut down!
4. The input power supply voltage is between AC115V and AC230V.
Product parameters
Working voltage:220V
Maximum load:2000W
Control switch:light touch switch
Relay rated power:30A*2
PCB Size:9.8*8*2.2CM
Hole pitch size:7cm*8.6cm
Package included
1 x Switch Delayed Start Board
Weight | 0.1 kg |
---|
Customers Also Viewed
Multiple Car Toys Magnetic Puzzle Box Book Educational Book Kids Learning Gift
$52.64MathematicsAdd to cartPackage included10 x Card76 x MagnetsFeatures1.Developing kids’ intelligence.2.Teaching kids to know more words.3.Easy for storage.SpecificationsColor:MulticolorMaterial:Paperboard, MagnetismSize:30x4x21.5cm
Basic Starter Kit UNO R3 Mini Breadboard LED Jumper Wire Button with Box for Geekcreit for Arduino – products that work with official Arduino boards
$18.62Module KitsAdd to cartDescriptionsPerfect for Shield Prototyping and TestingPlastic housing, metal contact clipsAccept wire with diameter 20-29AWGVolatge/current:300V/3-5A400 tie-point2 Power Lanes, Tie-point 1001 Double-strip, Tie-point 300Solderless Breadboard Size:82x55x8.5mmPackage included1 x Uno R3 Development Board1x 400 hole Breadboard10 x 220Ω resistor 5% carbon film10 x 1k resistor 5% carbon film10 x 10k resistor 5% carbon film10 x 100k resistor 5% …
3pcs ESP32-S WiFi + Bluetooth ESP32S Serial to WiFi Dual Antenna Module
$29.27Smart ModuleAdd to cartDescriptionThe main chip uses a low-power dual-core 32-bit CPU with a frequency of up to 240MHz and computing power of up to 600DMIPS.Default 32Mbit SPI Flash, 520KB SRAMSupport SoftAP and Station modeUltra-small 802.11b/g/n Wi-Fi + BT/BLE SoC moduleSupport UART/SPI/I2C/I2S/PWM/ADC/DAC, etc.Support for firmware upgrade (FOTA)Antenna supports onboard antenna or IPEX block outputPackage includes3 x Wifi module
Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter with Receiver
$15.30Smart ModuleAdd to cartIf you need more Transmitter, please buy Product ID:1215079>>>Manual:Click here to openFeaturesEasy to install and easy to carryWith a slidable cover on the remote controlWith a hook on the remote controlUse Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStream
$56.69Electrical Pump & ValveAdd to cartFeature*CO2 Refill Adapter is used to fill CO2 into your Sodastream tank.*Adjustable valve pin ensures compatibility with any cylinder valve variation.*Easy to install and use.*Made of high quality metal, high hardness and durable.Specification*Material:Metal*Color:Silver (As Pictures Show)*Inner Thread:TR21-4*Outer Thread:W21.8-14Package Contents1*CO2 Refill AdapterNotes:The real color of the item may be slightly different from the pictures shown on …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStreamRead More
30pcs 2.5-5.5V TTP223 Capacitive Touch Switch Button Self Lock Module
$15.15Other Module BoardAdd to cartFeatures 1. Size:15*11mm 2. Power:2.5-5.5V 3.Trigger setting mode:(1->Short;0->No Short) AB=00:No-lock High TTL level output; AB=01:Self-lock High TTL level output; AB=10:No-lock Low TTL level output; AB=11:Self-lock Low TTL level output; Package included 30 x 2.5-5.5V TTP223 Capacitive Touch Switch Button Self-Lock Module For
NE555 Pulse Module LM358 Duty and Frequency Adjustable Square Wave Signal Generator Upgrade Version
$6.55Test & Measuring ModuleAdd to cartFeature1. Used as a square wave signal generator to generate square wave signals for experimental development.2. Used to generate a square wave signal that drives the stepper motor driver.3. Generate adjustable pulses for use by the MCU.4. Generate adjustable pulses to control the associated circuitry.Description1. Size:3.5CM * 4.6CM1. The main chip:LM358;2. Input voltage:5V-12VDC.3. Input current:≥100MA;4. …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module Kit
$13.73DIY Electronic KitsAdd to cartFeatureModel:AUL-10Supply voltage:DC9V-12VAudio input:0~1.5VrmsPCB size:66 x 28mm (L x W)Light row size:62.5 x 5 x 10.7mm (L x W x H)Two indication modes:bar indication and fire spot indication (Realized by MOD short-circuit point)Lamp row offers two kinds of vertical and horizontal installationTin-treated solder padsNote:Before power on, please confirm the polarity of the power supply is correct …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module KitRead More
Reviews
There are no reviews yet.