2000W High Power Soft Start Board 30A Dual Temperature Control Switch Delayed Start Board for Amplifier Amp DIY
$38.31
Type #1 / Type #2 / Type #3 / Type #4 / Type #5 / Type #6 /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Type(option)
1:Terminal type Songchuan relay
2:Plug-in terminal type Songchuan relay
3:Plug-in terminal Songle relay
4:Terminal Type Songle Relay
5:Terminal type HF-105F-1 Relay
6:Plug-in terminal type HF-105F-1 Relay
Product description
Dual temperature control soft start uses high quality power module to replace traditional transformer, with low energy consumption, high efficiency, ultra stable, low heat, 105-235V wide voltage (for domestic and foreign), and so on!
This product PCB adopts 1.6MM thick double-sided fiberglass board, 2.0 oz copper thickness, tin-spraying process to ensure good passing of high current.
It is suitable for high-power amplifier and post-stage power supply as delay soft start board to avoid high current impact at the moment of booting and better protect your machine.
HF-105F-1 high current 30A power relay, stable and reliable performance, the maximum power can support 2000W.
Features
1. Delay start, the first relay is connected at the moment of power-on, and then the current is limited by the NTC thermistor. After a delay, the main relay is turned on to realize the soft-start function. Suppress the inrush current of the power amplifier, because the power of the class A and high power amplifier transformer is large, the load impedance is extremely low, and the capacity of the power supply filter capacitor is too large, resulting in excessive current of the power amplifier when the power is turned on, which easily damages the rectifier bridge and the damage filter capacitor.
2. 2 way overheat protection, use the attached 75 degree temperature control switch to install on the radiator,
When the temperature of the power amplifier board heat sink exceeds 75 degrees, the board can immediately cut off the power supply, and the power amplifier will not be overheated and burned. Until the temperature of the heat sink drops below 75 degrees, the power amplifier can be turned back on, otherwise the power amplifier can’t be turned on.
3. The power switch uses a tact switch, which is convenient and flexible. To prevent frequent machine damage to the machine.After the soft start is turned on, it takes about 12 seconds to shut down!
4. The input power supply voltage is between AC115V and AC230V.
Product parameters
Working voltage:220V
Maximum load:2000W
Control switch:light touch switch
Relay rated power:30A*2
PCB Size:9.8*8*2.2CM
Hole pitch size:7cm*8.6cm
Package included
1 x Switch Delayed Start Board
Weight | 0.1 kg |
---|
Customers Also Viewed
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-W
$90.79Amplifier BoardAdd to cartSpecifications– Supply Voltage:2.7v-5.5v @ 3mA current– Output:2Vpp on 1.25V bias– Frequency Response:20Hz – 20KHz– Programmable Attack and Release Ratio– Automatic gain, selectable max from 40dB, 50dB or 60dB– Low Input-Referred Noise Density of 30nV/– Low THD:0.04% (typ)– Low Power Shutdown Mode– Built-in 2V low-noise microphone bias– -40°C ~ +85°C extended temperature rangePackage included10 x Microphone …
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-WRead More
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMP
$19.04Amplifier BoardAdd to cartFeature1. The power to more than 12V current 3A2. The speaker is best to use an impedance of 4 ohms, some of the high sensitivity3. For some signal level is relatively low tone, to add the preamplifier to play the effect4. Note the positive and negative can not be reversed, use the power supplyElectrical CharacteristicsIts …
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMPRead More
Mega 2560 R3 ATmega2560-16AU Control Module without USB Cable
$44.54Motherboard & Development BoardAdd to cartDescriptionThis is compatible R3 Mega2560 ATmega2560-16AU control board without USB cableMega is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal …
Mega 2560 R3 ATmega2560-16AU Control Module without USB CableRead More
20W 420*380*3mm Folding PET Monocrystalline Silicon Solar Panel with Cable Dual USB
$93.62Smart Robot & Solar PanelAdd to cartSpecificationsMaximum Power(Pmax):20WOpen Circuit Voltage(Voc):18VMaximum Power Voltage(Vmp):12vMaximum Power Current(Imp):1.1AMaximum System Voltage(Imp):1000vOutput:USB 5V & DC 18VQuantity of cell:36Cell Effcience %:20%Output Tolerance:±10%Size:425*380*3mmStandard Test Conditions:Irradiance 1000w/m2Temoerature 25.C,AM=1.5Package Included1 x Solar panel with cable
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLC
$45.10Relay ModuleAdd to cartDescriptions– Operating Voltage:DC 5V(5V Version)– Operating Current:10-15MA– inchopeninch inchcloseinch inchMomentaryinch inchSelf-lockinginch inchInterlockinch inchDelayinch 6 Commands– Two instruction-control mode:AT command and MODBUS command– Under the AT command ,the maximum delay is 9999 seconds– Under the MODBUS command ,the maximum delay is 255 seconds– AT commands can be made serial HyperTerminal (serial assistant) Enter;– MODBUS commands can …
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLCRead More
LT1083cp 7A AC 35V Rectifier Filter Power Supply Board DIY Home theater Sound Amplifier Voltage Regulator
$24.04Power Supply ModuleAdd to cartDescriptionLT1083CP feature description (emphasis):It is a linear step-down block. Although the voltage adjustment can be adjusted from 2.5V to 37V, it is recommended that the working differential pressure is within 10V, because the power consumption is proportional to the differential pressure, the greater the differential pressure, the more heat The larger the output current, the …
Reviews
There are no reviews yet.