1:200 High Simulation Missile Destroyer Battleship Model DIY Education Building Toys
$58.71
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Painting Style:Color.
Scale:1:200 (approx 82cm)
Size:A4 Standard Version (ratio 1:200, when you make good, about 82 cm long).
Difficulty:Level 5 (6 is the most advanced and the most difficult).
Feature:High simulation
Color:As picture
Material:Paper
Size:about 82 cm/32inch (when you make it).
Net weight:no cardboard, about 0.36KG, containing cardboard, about 0.59KG
Features
– It was not finished product, it need you to cut, paste and assemble.
– The cutter and glue are not included.
– Non paper components, such as ropes, are not included in this set.
– It’s about 82 cm/32inch (when you make it).
Guide To Build
Basic steps to make Paper Models.
1. Cut out each part roughly.
2. Use a pencil to mark note softly behind each part to avoid disorder (Don’t use a pen as it probably makes damaged trace on the front side).
3. Use Scissor or Craft K`nife to cut parts precisely by following the outer edge. The level of precision affects the effect of combination. (Cut the most outer edge if the line is thick).
4. Smear white adhesive cement on one of the 2 parts which needed to be stuck together.
5. Stick them together until the cement bone-dry.
Suggested Tips
A. For Scissor cutting, suggest not to push the Scissor but pull the paper.
B. To make the fold of parts better, please put the part firmly on the table, and put the ruler on that to fold the line. If you have to fold inside, you could first fold it softly outside to make the trace, and fold it back to inside then.
C. To make the curved parts better, place the part on the corner of table then push and pull it back and forth.
D. To make parts like cylinder, use tools such as pen to assist to make the curl more natural.
Note
1.The paper model requires you to cut, paste and assemble your own models, more parts,there are schematic drawings, difficult, suitable for senior enthusiasts to produce.
2.Please allow 0.5-1 inch difference due to manual measurement. (1inch=2.54cm)
3.The color of the actual items may slightly different from the listing images due to different computer screen, thanks for your understanding.
Package Included
1 Set x 1:200 Battleship DIY Model
Weight | 0.365 kg |
---|
Customers Also Viewed
5pcs ESP-32S Matching Adapter Board WIFI bluetooth Module ESP-WROOM-32 Module for DIP
$9.84Smart ModuleAdd to cartFeaturesESP-32S supporting adapter board, 2.54mm pitch, lead RESET and IO 0 port, can be inserted into the breadboard, use DuPont wire leads, etc., to facilitate development and debugging.Package Included5 x ESP-32S Matching Adapter Board
5 Channel Flame Sensor Module Analog Dgital Dual Output Fire Extinguishing Robot Flame Alarm System Module
$13.11Sensor & Detector ModuleAdd to cartFeatures1.Using a five-way flame sensor design, the detection range is wide (the detection range of a common single flame sensor is about 30°, and the range is gradually reduced as the distance increases, the detection range of this product is greater than 120°)2.Can output digital signals (high and low level), easy to use3. can output …
600W Mini 2CH HiFi Digital Audio Stereo Amplifier Bass bluetooth FM Radio Amplifiering Equipment
$109.34Switch AccessoriesAdd to cartSpecificationsColor:BlueType:Support bluetoothInput voltage:220V-240V 50/60Hz 12V(in car)Plug:US plugRated power:80W+80WPeak power:300W+300WChannel:2 CHLoad impedance:4-16ΩSNR:>90 dbFM frequency:88-108MHzDistoration rate:0.05%Frequency:20Hz-20KHz(±3dB)Total harmonic distortion:less than 0.5% (normal operating conditions)Signal input sensitivity:200MV (±30MV)MIC input sensitivity:9mV (±2mV)Record level output:1VAuxiliary output level:1VSensitivity:0.25mV-220mVRC power supply:CR2052 battery(built-in)Features-Mini HIFI digital bluetooth audio power amplifier.-SD Card, U disk, MP3 format play, support bluetooth wireless connection.-Supports FM stereo radio.-Two microphone input …
Reviews
There are no reviews yet.