Mini Jewelry Gas Mirco Torch Welding Brazing Cutting Tools
$109.34
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Material:Metal
Color:Multicolors
The highest welding temperature:1700℃
Interchangeable Torch Tip Length:43mm /1.69inch(appr.)
Length:205cm /80.71inch(appr.)
Features
Ideal for jewelry repair and construction, hobbyists, crafts, metal sculpture, glass blowing, and electronics repair and manufacturing. It can weld an unlimited range of materials.
Torch
The torch is designed to meet the requirements of industry for a small, lightweigh torch to weld, braze, heat and solder materials ranging from 3/16 Inch metal to ultra-fine wires. The six tips available provide a wide range of flame sizes allowing the versatility to perform many different tasks. Light weight construction and highly flexible hose provide pinpoint welding with maximum control.
Gases
The product can be used with most comonly available pressurized fuel gases:acetylene, hy-drogen, propanes, propylenes, natural gas or mapp with oxygen. The two smallest tips, sizes 1 and 2, can only be used satisfactorily with acetylene and hy-drogen fuel gases. CAUTION:When using natural gas, a minimum of 1 pound of pressure is required. Higher pressures are necessary for use with melting tips.
Tips
There are six tips available for the torch. SIZE 1, 2 AND 3 ARE FITTED WITHA SYNTHETIC SAPPHIRE to assure accurate gas flow because of the extraordinary small orifice size. There are also two different heating tips available, one for use with all gases and another specially designed for propane or natural gas. Refer to the pressure recommendation chart provided in this booklet for being used.
Repairs/Replacement of Hose
The torch hose is a special material designed to be compatible with the various fuel gases. The maximum length of hose used should not exceed 12 feet.
※EYE PROTECTION
Oxy-fuel flames produce hazardous rays of light(infrared/ultraviolet). An approved filter lens is required for eye protection when operation oxy-fuel equipment. Approved safety glasses are required in conjuncting with a filtered eye protection device.
※PROPER CLOTHING
Hazardous rays of light, molten metal, or sparks can cause severe burns to unprotected parts of the body. Appropriate protective clothing such as gloves, aprons, safety shoes, etc, are required when using oxy-fuel equipment.
WARNING:Keep all clothing and protective equipment free of oil and grease. These substances can ignite and will burn violently in the presence of pure of oxygen.
HOUSEKEEPING AND FIRE PROTECTION
The safety of any work area can be improved by following good housekeeping practices.
1. The work place must have a fireproof floor.
2. Work benches must have fireproof tops.
3. Nearby walls and unprotected flooring should be protected from sparks and hot metal by the use of heat resistant shields or other approved material.
4. An approved fire extinguisher must be kept and maintained (check regularly) in the work area.
5. The work site should be cleared of combustible materials. If such materials cannot be removed, they must be protected with fireproof covers and a fire watch should be established.
Package Included
1 x Mini Gas Torch
5 x Interchangeable Torch Tip
1 x English User Manual
Weight | 0.319 kg |
---|
Customers Also Viewed
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-W
$90.79Amplifier BoardAdd to cartSpecifications– Supply Voltage:2.7v-5.5v @ 3mA current– Output:2Vpp on 1.25V bias– Frequency Response:20Hz – 20KHz– Programmable Attack and Release Ratio– Automatic gain, selectable max from 40dB, 50dB or 60dB– Low Input-Referred Noise Density of 30nV/– Low THD:0.04% (typ)– Low Power Shutdown Mode– Built-in 2V low-noise microphone bias– -40°C ~ +85°C extended temperature rangePackage included10 x Microphone …
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-WRead More
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMP
$19.04Amplifier BoardAdd to cartFeature1. The power to more than 12V current 3A2. The speaker is best to use an impedance of 4 ohms, some of the high sensitivity3. For some signal level is relatively low tone, to add the preamplifier to play the effect4. Note the positive and negative can not be reversed, use the power supplyElectrical CharacteristicsIts …
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMPRead More
Mega 2560 R3 ATmega2560-16AU Control Module without USB Cable
$44.54Motherboard & Development BoardAdd to cartDescriptionThis is compatible R3 Mega2560 ATmega2560-16AU control board without USB cableMega is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal …
Mega 2560 R3 ATmega2560-16AU Control Module without USB CableRead More
20W 420*380*3mm Folding PET Monocrystalline Silicon Solar Panel with Cable Dual USB
$93.62Smart Robot & Solar PanelAdd to cartSpecificationsMaximum Power(Pmax):20WOpen Circuit Voltage(Voc):18VMaximum Power Voltage(Vmp):12vMaximum Power Current(Imp):1.1AMaximum System Voltage(Imp):1000vOutput:USB 5V & DC 18VQuantity of cell:36Cell Effcience %:20%Output Tolerance:±10%Size:425*380*3mmStandard Test Conditions:Irradiance 1000w/m2Temoerature 25.C,AM=1.5Package Included1 x Solar panel with cable
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLC
$45.10Relay ModuleAdd to cartDescriptions– Operating Voltage:DC 5V(5V Version)– Operating Current:10-15MA– inchopeninch inchcloseinch inchMomentaryinch inchSelf-lockinginch inchInterlockinch inchDelayinch 6 Commands– Two instruction-control mode:AT command and MODBUS command– Under the AT command ,the maximum delay is 9999 seconds– Under the MODBUS command ,the maximum delay is 255 seconds– AT commands can be made serial HyperTerminal (serial assistant) Enter;– MODBUS commands can …
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLCRead More
LT1083cp 7A AC 35V Rectifier Filter Power Supply Board DIY Home theater Sound Amplifier Voltage Regulator
$24.04Power Supply ModuleAdd to cartDescriptionLT1083CP feature description (emphasis):It is a linear step-down block. Although the voltage adjustment can be adjusted from 2.5V to 37V, it is recommended that the working differential pressure is within 10V, because the power consumption is proportional to the differential pressure, the greater the differential pressure, the more heat The larger the output current, the …
Reviews
There are no reviews yet.