100w 3-speed Silent Hot Water Circulation Pump for Household Solar Heater System
$139.71
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Material:Cast Iron
Color:Green+Black
Power:100W, 50Hz
Voltage:220v~240v
Head:6M
Capacity:50L/min
Circulation area:Less than 50㎡
Connector:25mm(Outer diameter)
Plug Type:China National Standard Plug (We will be based on your country to send the corresponding adapter plug)
Features
Low noise ,no leakage
Robust cast iron construction
3-Stall speed adjustment according your own need
The red button facilitates pre-selection of the pump ooutput
Up to 20% less electrical current consumption in comparison to convenientional standard pumps
Widely used in city buildings, suburban villas, houses, water and pressurized with industrial equipment, air conditioning, boilers, solar circulating water, hot water circulating warm and so on.
The main purpose
The pump is suitable for hot and cold water circulation below 100 °C and supercharging, especially the shower is difficult to ignite due to low water pressure or the water pressure is unstable and easy to fire. Installation and use of this pump can completely solve the problem:the household water pressure is too low and supercharged Water supply; solar water heater water supply, boiler hot water circulation pressurization, industrial equipment liquid pressurization cycle, air conditioning and refrigeration system circulating pressurization
Precautions for use
1. After the pump is installed, connect the power supply and try to turn it for a few minutes (check whether the startup is normal), but the idle time should not be too long to prevent the dry running from affecting the life of the ceramic bearing.
2. When using this product in the home, you should pay attention to the exhaust of the pump, or when it is overhauled, the dripping water will prevent moisture on the board and the moisture-prone items.
3. When the product is supplied with water in the heating system, do not touch it with your hands to prevent burns.
4. Before installing the water pump, it should be ensured that the pipeline has no slag. If there are impurities, welding slag, dirt, etc., it will damage the life of the pump.
5. The pump should be installed in a place that is easy to repair or replace later.
6. Pay attention to the direction of water flow when the pump is installed. The direction of the water flow should be consistent with the water flow mark of the pump.
7. If the direction of the junction box hits the wall or the shift switch is not easy to operate during installation,you can loosen the four hex screws on the pump head. Rotate the motor body until the position is required, please be careful not to damage the rubber washer, then re-tighten the screw evenly and check if the seal line leaks.
Package included
1 X Circulating Pump
Weight | 1.857 kg |
---|
Customers Also Viewed
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820io
$15.30Converter BoardAdd to cart>>>Manual:Click here to openOverviewUSR-ES1 embeds Wiznet’s W5500 chip, which uses hardware logic gates to implement the transport layer and network layer of the TCP/IP protocol stack (such as TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE, etc.), and integrates The data link layer, physical layer, and 32K bytes of on-chip RAM serve as data transceiving buffers. …
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820ioRead More
3pcs TEC1-12715 12V Heat Sink thermoelectric Cooler Peltier Plate Module
$32.04Electronic Accessories & SuppliesAdd to cart40 x 40mm TEC1-12715 12V Heatsink Thermoelectric Cooler Peltier Plate ModuleDescriptionSolid state, vibration free, noise-freeSimple to install and operateThe hot surface need to be good heat sinkSpecificationProduct name:thermoelectric cooler plate moduleModel:TEC1-12715Color:whiteCouples:127Voltage:12VUmax:15.4VImax:15AMax power consumption:231WTmax:70°CQcmax T=0(W):137WSize:40 x 40 x 3.3mmWeight:50gPackage included3 x TEC1-12715 cooler plate module
EQKIT KM-1 DC 6-12V PWM Motor Speed Controller Kit DIY Motor Speed Regulator Set Stepless Speed Control
$8.73Module KitsAdd to cartSpecificationsModel:KM-1Operating voltage:DC 6-12VPCB board size:40 x 40mmCircuit descriptionKM-1 uses PWM (pulse width modulation) to control the speed of the motor, adjust the pulse width duty ratio, so that the speed from zero to the maximum speed stepless speed regulation. The wider the crest width of the control waveform, the faster the motor speed; on the …
20pcs 63V 10000UF 105 High Frequency Temp Electrolytic Capacitor 30mm x 50mm Long Life
$108.62Electronic Accessories & SuppliesAdd to cartSpecificationModel:485622Voltage:63VCapacitance:10000UFTemperature:105→Diameter:30mm / 1.1 inchHeight:50 mm / 2 inchFeaturesLong life, high temperatureHigh-frequency capacitorsPackage included20 x Electrolytic Capacitor
Reviews
There are no reviews yet.