TKS-M8 4-40V DC Motor Speed forward and Reverse Controller with Shell 20A Relay P0 Optocoupler Isolation Anti-jamming
$17.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Working voltage:4-40V DC
Module power consumption:0.6W (static 0.1W)
Signal input:active low. The input is the negative of the optocoupler. A signal is considered to be present when the voltage is below 2V.
Response speed:K1 K2 is 20mS, SW1 SW2 is 50mS.
Output current 20A
PCB size:83*46*20mm
Shell size:87*54*59mm
User Manual
K1:Forward signal
K2:Reverse signal
SW1:Forward limit
SW2:Reverse limit
1. Press K1 and the motor will start to rotate immediately until SW1 closes.
2. Press K2 and the motor immediately starts to reverse until SW2 closes and stops.
3. When K2 is pressed during forward rotation, it will switch to reverse immediately. When K1 is pressed during reverse rotation, it will switch to forward rotation immediately.
1. What mode is P0
P0 is self-locking mode. For example, if the external forward switch (K1) is pressed, the motor will immediately rotate forward. At this time, the instant switch will be released and the motor will continue to rotate forward. It will not stop until the reverse signal (K2) or the forward stop signal (SW1) is encountered.
2. What are the requirements for the signal, can I connect the sensor
The signal is active low and can be a three-wire sensor (NPN-NO type). K1 K2 SW1 SW2 is still the specification.
3. What is the input and output voltage
The input voltage range of the TKS-M8 is 4V~40V, but to ensure reliable operation, it is recommended to use it within the range of 6V-36V. This module is wide voltage. The output motor is the same as the input voltage.
4. What is the limit signal
The limit signal can also be referred to as a stop signal. The limit signal is triggered and level enabled. For example, if a short limit signal is encountered during forward rotation, it will stop, even if the limit signal disappears, it will stop. You must re-transmit the signal once again to get forward again.
5. Can drive a large motor
The maximum current of the TKS-M8 at 12V is 20A, and the maximum current is 10A when the voltage is 24V. The maximum drive motor power is generally not more than 80W. It is recommended that the motor’s stall motor be the standard.
7. Can I achieve automatic forward and reverse
The TKS-M8 does not have a timing function, so strictly speaking, it cannot automatically reciprocate. However, with the start switch, the start switch (A), and the end switch (B), it is possible to achieve infinite reciprocating operation between the two points A and B. Connection method:The start switch and the start switch are connected to K1, the end switch is connected to K2, and SW1 SW2 is not connected. Note that all switches are normally open.
Package Included
1 x TKS-M8 P0 4-40V DC Motor Forward and Reverse Controller with Shell
Weight | 0.081 kg |
---|
Customers Also Viewed
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-W
$90.79Amplifier BoardAdd to cartSpecifications– Supply Voltage:2.7v-5.5v @ 3mA current– Output:2Vpp on 1.25V bias– Frequency Response:20Hz – 20KHz– Programmable Attack and Release Ratio– Automatic gain, selectable max from 40dB, 50dB or 60dB– Low Input-Referred Noise Density of 30nV/– Low THD:0.04% (typ)– Low Power Shutdown Mode– Built-in 2V low-noise microphone bias– -40°C ~ +85°C extended temperature rangePackage included10 x Microphone …
10pcs MAX9814 High Performance Microphone AGC Amplifier Module CMA-4544PF-WRead More
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMP
$19.04Amplifier BoardAdd to cartFeature1. The power to more than 12V current 3A2. The speaker is best to use an impedance of 4 ohms, some of the high sensitivity3. For some signal level is relatively low tone, to add the preamplifier to play the effect4. Note the positive and negative can not be reversed, use the power supplyElectrical CharacteristicsIts …
T-AMP 2 x 15W TA2024 Digital Audio Amplifier Board Mini AMPRead More
Mega 2560 R3 ATmega2560-16AU Control Module without USB Cable
$44.54Motherboard & Development BoardAdd to cartDescriptionThis is compatible R3 Mega2560 ATmega2560-16AU control board without USB cableMega is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal …
Mega 2560 R3 ATmega2560-16AU Control Module without USB CableRead More
20W 420*380*3mm Folding PET Monocrystalline Silicon Solar Panel with Cable Dual USB
$93.62Smart Robot & Solar PanelAdd to cartSpecificationsMaximum Power(Pmax):20WOpen Circuit Voltage(Voc):18VMaximum Power Voltage(Vmp):12vMaximum Power Current(Imp):1.1AMaximum System Voltage(Imp):1000vOutput:USB 5V & DC 18VQuantity of cell:36Cell Effcience %:20%Output Tolerance:±10%Size:425*380*3mmStandard Test Conditions:Irradiance 1000w/m2Temoerature 25.C,AM=1.5Package Included1 x Solar panel with cable
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLC
$45.10Relay ModuleAdd to cartDescriptions– Operating Voltage:DC 5V(5V Version)– Operating Current:10-15MA– inchopeninch inchcloseinch inchMomentaryinch inchSelf-lockinginch inchInterlockinch inchDelayinch 6 Commands– Two instruction-control mode:AT command and MODBUS command– Under the AT command ,the maximum delay is 9999 seconds– Under the MODBUS command ,the maximum delay is 255 seconds– AT commands can be made serial HyperTerminal (serial assistant) Enter;– MODBUS commands can …
5pcs 8Channel DC 5V RS485 Modbus RTU Control Module UART Relay Switch Board PLCRead More
LT1083cp 7A AC 35V Rectifier Filter Power Supply Board DIY Home theater Sound Amplifier Voltage Regulator
$24.04Power Supply ModuleAdd to cartDescriptionLT1083CP feature description (emphasis):It is a linear step-down block. Although the voltage adjustment can be adjusted from 2.5V to 37V, it is recommended that the working differential pressure is within 10V, because the power consumption is proportional to the differential pressure, the greater the differential pressure, the more heat The larger the output current, the …
Reviews
There are no reviews yet.