TKS-M8 4-40V DC Motor Speed forward and Reverse Controller with Shell 20A Relay P0 Optocoupler Isolation Anti-jamming
$17.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Working voltage:4-40V DC
Module power consumption:0.6W (static 0.1W)
Signal input:active low. The input is the negative of the optocoupler. A signal is considered to be present when the voltage is below 2V.
Response speed:K1 K2 is 20mS, SW1 SW2 is 50mS.
Output current 20A
PCB size:83*46*20mm
Shell size:87*54*59mm
User Manual
K1:Forward signal
K2:Reverse signal
SW1:Forward limit
SW2:Reverse limit
1. Press K1 and the motor will start to rotate immediately until SW1 closes.
2. Press K2 and the motor immediately starts to reverse until SW2 closes and stops.
3. When K2 is pressed during forward rotation, it will switch to reverse immediately. When K1 is pressed during reverse rotation, it will switch to forward rotation immediately.
1. What mode is P0
P0 is self-locking mode. For example, if the external forward switch (K1) is pressed, the motor will immediately rotate forward. At this time, the instant switch will be released and the motor will continue to rotate forward. It will not stop until the reverse signal (K2) or the forward stop signal (SW1) is encountered.
2. What are the requirements for the signal, can I connect the sensor
The signal is active low and can be a three-wire sensor (NPN-NO type). K1 K2 SW1 SW2 is still the specification.
3. What is the input and output voltage
The input voltage range of the TKS-M8 is 4V~40V, but to ensure reliable operation, it is recommended to use it within the range of 6V-36V. This module is wide voltage. The output motor is the same as the input voltage.
4. What is the limit signal
The limit signal can also be referred to as a stop signal. The limit signal is triggered and level enabled. For example, if a short limit signal is encountered during forward rotation, it will stop, even if the limit signal disappears, it will stop. You must re-transmit the signal once again to get forward again.
5. Can drive a large motor
The maximum current of the TKS-M8 at 12V is 20A, and the maximum current is 10A when the voltage is 24V. The maximum drive motor power is generally not more than 80W. It is recommended that the motor’s stall motor be the standard.
7. Can I achieve automatic forward and reverse
The TKS-M8 does not have a timing function, so strictly speaking, it cannot automatically reciprocate. However, with the start switch, the start switch (A), and the end switch (B), it is possible to achieve infinite reciprocating operation between the two points A and B. Connection method:The start switch and the start switch are connected to K1, the end switch is connected to K2, and SW1 SW2 is not connected. Note that all switches are normally open.
Package Included
1 x TKS-M8 P0 4-40V DC Motor Forward and Reverse Controller with Shell
Weight | 0.081 kg |
---|
Customers Also Viewed
Multiple Car Toys Magnetic Puzzle Box Book Educational Book Kids Learning Gift
$52.64MathematicsAdd to cartPackage included10 x Card76 x MagnetsFeatures1.Developing kids’ intelligence.2.Teaching kids to know more words.3.Easy for storage.SpecificationsColor:MulticolorMaterial:Paperboard, MagnetismSize:30x4x21.5cm
Basic Starter Kit UNO R3 Mini Breadboard LED Jumper Wire Button with Box for Geekcreit for Arduino – products that work with official Arduino boards
$18.62Module KitsAdd to cartDescriptionsPerfect for Shield Prototyping and TestingPlastic housing, metal contact clipsAccept wire with diameter 20-29AWGVolatge/current:300V/3-5A400 tie-point2 Power Lanes, Tie-point 1001 Double-strip, Tie-point 300Solderless Breadboard Size:82x55x8.5mmPackage included1 x Uno R3 Development Board1x 400 hole Breadboard10 x 220Ω resistor 5% carbon film10 x 1k resistor 5% carbon film10 x 10k resistor 5% carbon film10 x 100k resistor 5% …
3pcs ESP32-S WiFi + Bluetooth ESP32S Serial to WiFi Dual Antenna Module
$29.27Smart ModuleAdd to cartDescriptionThe main chip uses a low-power dual-core 32-bit CPU with a frequency of up to 240MHz and computing power of up to 600DMIPS.Default 32Mbit SPI Flash, 520KB SRAMSupport SoftAP and Station modeUltra-small 802.11b/g/n Wi-Fi + BT/BLE SoC moduleSupport UART/SPI/I2C/I2S/PWM/ADC/DAC, etc.Support for firmware upgrade (FOTA)Antenna supports onboard antenna or IPEX block outputPackage includes3 x Wifi module
Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter with Receiver
$15.30Smart ModuleAdd to cartIf you need more Transmitter, please buy Product ID:1215079>>>Manual:Click here to openFeaturesEasy to install and easy to carryWith a slidable cover on the remote controlWith a hook on the remote controlUse Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStream
$56.69Electrical Pump & ValveAdd to cartFeature*CO2 Refill Adapter is used to fill CO2 into your Sodastream tank.*Adjustable valve pin ensures compatibility with any cylinder valve variation.*Easy to install and use.*Made of high quality metal, high hardness and durable.Specification*Material:Metal*Color:Silver (As Pictures Show)*Inner Thread:TR21-4*Outer Thread:W21.8-14Package Contents1*CO2 Refill AdapterNotes:The real color of the item may be slightly different from the pictures shown on …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStreamRead More
30pcs 2.5-5.5V TTP223 Capacitive Touch Switch Button Self Lock Module
$15.15Other Module BoardAdd to cartFeatures 1. Size:15*11mm 2. Power:2.5-5.5V 3.Trigger setting mode:(1->Short;0->No Short) AB=00:No-lock High TTL level output; AB=01:Self-lock High TTL level output; AB=10:No-lock Low TTL level output; AB=11:Self-lock Low TTL level output; Package included 30 x 2.5-5.5V TTP223 Capacitive Touch Switch Button Self-Lock Module For
NE555 Pulse Module LM358 Duty and Frequency Adjustable Square Wave Signal Generator Upgrade Version
$6.55Test & Measuring ModuleAdd to cartFeature1. Used as a square wave signal generator to generate square wave signals for experimental development.2. Used to generate a square wave signal that drives the stepper motor driver.3. Generate adjustable pulses for use by the MCU.4. Generate adjustable pulses to control the associated circuitry.Description1. Size:3.5CM * 4.6CM1. The main chip:LM358;2. Input voltage:5V-12VDC.3. Input current:≥100MA;4. …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module Kit
$13.73DIY Electronic KitsAdd to cartFeatureModel:AUL-10Supply voltage:DC9V-12VAudio input:0~1.5VrmsPCB size:66 x 28mm (L x W)Light row size:62.5 x 5 x 10.7mm (L x W x H)Two indication modes:bar indication and fire spot indication (Realized by MOD short-circuit point)Lamp row offers two kinds of vertical and horizontal installationTin-treated solder padsNote:Before power on, please confirm the polarity of the power supply is correct …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module KitRead More
Reviews
There are no reviews yet.