48V Wind Generator Controller 500W Wind Turbine Generator Controller
$127.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Package list
1x Controller
Specifications
Rated battery voltage:48V
Wind generator braking voltage:60V
Wind generator recover voltage:54V
Protection class:IP67
Precautions
1. Verify that the wind turbine output voltage matches the rated voltage of the battery.
2. Wire in the following order, first connect the positive and negative terminals of the battery, and then connect the three-phase voltage output of the fan.
3. Please carefully connect the battery and the wind turbine to the controller according to the instructions. Connecting the reverse polarity or the wrong position will cause the system to work abnormally and may even cause damage to the system components.
4. Although the controller has taken protective measures against various possible accidents, it is strongly recommended that users strictly abide by the operating procedures to prevent damage to the battery and controller.
Wiring
1. Connect the “+ Inch and “- Inch of the battery to the positive and negative terminals of the battery of the controller.
2. Connect the three-phase output voltage of the wind turbine to the three-phase voltage input terminal of the controller fan.
3. When manual brake is required, short the red thin wire to the positive battery, that is, complete the manual brake function. To cancel this function, just disconnect the thin red wire.
Indicator status
– When the controller green power (BATTERY) indicator is on, it indicates that the battery is connected properly.
– When the controller’s green fan access (WIND) indicator flashes, it indicates that the wind turbine is connected. The speed of the flashing reflects the speed of the fan.
– When the controller red (BRAKE) indicator is on, the battery is fully charged, the wind turbine is automatically braked, or the brake is automatically activated due to overcurrent protection.
Weight | 0.978 kg |
---|
Customers Also Viewed
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with Cable
$11.26Sensor & Detector ModuleAdd to cartFeatures– Can receive standard 38KHz remote control signals by means of programming can decode the remote control signals– Strong ability to resist electromagnetic interference and light– Widely used in stereo, TV, set-top boxes, digital photo frame, car stereo, remote control toys, satellite receivers, hard disk players, air conditioner, heater, electric fan, lighting and other home …
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with CableRead More
600V 45A 3 Position Terminal Block Barrier Strip Dual Row Screw Block Covered W/ Removable Clear Plastic insulating Cover
$16.19Terminal BlocksAdd to cartSpecificationModel:TB4503Type:Terminal block Working frequency:High frequencyInterface type:AC/DCRated current:45ARated voltage:600VConductor cross section:0.5-4mm2Number of pin:6Number of bits:3Contact material:IronSize:70mm x 38mm x 24mmFeature:–Moistureproof–High quality guides,durable–High quality thickened conductive parts–High quality iron screw with high strength–Dust proof transparent plastic protective coverPackage Included1 x Terminal block
5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V inverter
$26.31Smart ModuleAdd to cart5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V Inverter For 10 Inch To 22 Inch ScreenFeatureVoltage:10V ~ 28VCable:300mm(L) / 6 pinSize:122 x 27mm ( L x W )Interface:double light small interfaceInterface definition:1. VCC 2. GND 3. NULL 4. NULL 5. ON/OFFPackage included5 x 2 lamp backlight universal laptop LCD CCFL inverter 10V-28V5 x Cable
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier Board
$20.90Amplifier BoardAdd to cartFeatures1. Power filter function is through the power line access power filter,get a specific frequency of the power signal, or eliminate a specific frequency power signal. By using this feature of the power filter, a square wave complex or complex noise passing through the power filter can be converted into a sine wave of a …
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier BoardRead More
5pcs EQKIT TDL-555 Touch Delay LED Light DIY Kit Touch Delay Lamp Electronic Parts Production Kit DC 5V 3s to 130s Adjustable
$10.12DIY Electronic KitsAdd to cartFunction1. Connect Power,Red LED ON2. Touch and then start to delay and Red LED OFF and 5pcs White LED ON at the same time3. Red LED ON and White LED OFF after delay4. Delay can be adjust by potentiometer for 3-130 secondPackage included5 x EQKIT® TDL-555 Touch Delay LED Light DIY Kit
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4
$22.95Raspberry Pi & Orange PiAdd to cartOverviewThis is a universal driver board for e-Paper panels, can be used to drive various SPI interface e-Paper from Waveshare.FeaturesStandard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson NanoSPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.Onboard voltage translator, compatible with 3.3V/5V MCUsComes with development resources and manual (examples …
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4Read More
Reviews
There are no reviews yet.