48V Wind Generator Controller 500W Wind Turbine Generator Controller
$127.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Package list
1x Controller
Specifications
Rated battery voltage:48V
Wind generator braking voltage:60V
Wind generator recover voltage:54V
Protection class:IP67
Precautions
1. Verify that the wind turbine output voltage matches the rated voltage of the battery.
2. Wire in the following order, first connect the positive and negative terminals of the battery, and then connect the three-phase voltage output of the fan.
3. Please carefully connect the battery and the wind turbine to the controller according to the instructions. Connecting the reverse polarity or the wrong position will cause the system to work abnormally and may even cause damage to the system components.
4. Although the controller has taken protective measures against various possible accidents, it is strongly recommended that users strictly abide by the operating procedures to prevent damage to the battery and controller.
Wiring
1. Connect the “+ Inch and “- Inch of the battery to the positive and negative terminals of the battery of the controller.
2. Connect the three-phase output voltage of the wind turbine to the three-phase voltage input terminal of the controller fan.
3. When manual brake is required, short the red thin wire to the positive battery, that is, complete the manual brake function. To cancel this function, just disconnect the thin red wire.
Indicator status
– When the controller green power (BATTERY) indicator is on, it indicates that the battery is connected properly.
– When the controller’s green fan access (WIND) indicator flashes, it indicates that the wind turbine is connected. The speed of the flashing reflects the speed of the fan.
– When the controller red (BRAKE) indicator is on, the battery is fully charged, the wind turbine is automatically braked, or the brake is automatically activated due to overcurrent protection.
Weight | 0.978 kg |
---|
Customers Also Viewed
5Pcs MAX7219 Dot Matrix Module MCU LED Control Module Kit
$26.64Other Module BoardAdd to cartSpecificationsA single module can drive an 8 x 8 common cathode latticeOperating voltage:5VSize:5 x 3.2 x 1.5 cm (L x W x H)LED color:RedWith four screws hole, aperture 3mmWith input and output interfaces, supports multiple modules cascadeWiring instructions1. The module left side as an input port and the output port on the right2. To control …
5Pcs MAX7219 Dot Matrix Module MCU LED Control Module KitRead More
Geekcreit DIY Electronics Basic Starter Kit Breadboard Jumper Wires Resistors Buzzer for UNO R3 Mega2560
$35.71DIY Electronic KitsAdd to cartPackage included1 x power supply module1 x 400 hole breadboard1 x small resistor card1 x 90 degree 40 pin header1 x 40-pin header1 x 9V battery connection for Ardunio1 x 65 jumper wire1 x active buzzer1 x passive buzzer1 x relay3 x 10k adjustable potentiometer3 x 10k potentiometer1 x 10k adjustable potentiometer5 x 100uf electrolytic …
TDA2030A 2.1 Stereo Audio Amplifier 3 Channel Subwoofer Amplifier Board
$22.38Amplifier BoardAdd to cartNote:This is a DIY kit, you need to assemble it.FeaturesProduct name:2.1 Audio amplifier boardAdjustment type:Master Volume + Treble + BassChip selection:TDA2030APower range:AC8-18V * 2Recommended power:AC12V * 2 30WPCB material:FR-4 fiberglass boardChannel type:Stereo + SubwooferLeft and right channel:TDA2030Ax2Bass output:TDA2030Ax1Quiescent current:60MA (AC12V time)Signal to noise ratio:85%Recommended speaker:30-100WInput impedance:2K-3KOutput impedance:4-16ΩOutput power:18W +18 W (4-6 inch,4-8Ω speaker) + 20-70W …
TDA2030A 2.1 Stereo Audio Amplifier 3 Channel Subwoofer Amplifier BoardRead More
STM32F103ZET6 Core Board Minimum System Board STM32 Development Board ARM Learning Board Cortex-M3
$27.26Motherboard & Development BoardAdd to cart>>>Manual:Click here to openOverviewThis is based on STM32F103ZET6 as the main chip, crystal oscillator circuit, reset circuit and program programming circuit to form the ARM system core board. The reasonable circuit design ensures that the MCU can work. The EEPROM peripheral has been extended on this basis. The SPF reserves NandFLash and SRAM peripheral pads, …
10pcs XH-M229 Desktop Computer Chassis Power Supply Module ATX Transfer Board Power Output Terminal Module
$66.00Power Supply ModuleAdd to cartSpecificationModel:XH – M229Compatible with the port:ATX (compatible with partial BTX type)The PIN number:24 pinSwitch:YesNumber of sets of output:Four sets of different voltageSize:12.8×4.8cm/5.04×1.89inchPackage included10 x XH-M229 24 Pin Desktop Chassis Power Supply ATX Adapter Board Module
2500W 50A ZVS induction Heating Module High Frequency Heating Machine Melted Metal+48V Coil+Water Pipe+Water Pump Kit
$186.33Power Supply ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.IntroductionThis version is a 2500W upgrade of the 1800W ZVS heating module, using an oversized PCB layout design and an oversized heat sink for heat dissipation.Good power, self-contained cooling fan interface, can …
399PCS 3D Creative Electric Drill Toys Set Drilling Screw Puzzle Toy Kid Gift
$54.66PhysicsAdd to cartSpecificationsName:DIY Puzzle ToyMaterial:ABSQuantity:399PCSColor:Multi-colorExpand Size:48x30cm/18.72×11.70inchFold size:24×6.5x30cm/9.36×2.54×11.70inch(1cm=10mm=0.39inch)Measurement Details in the attached picture.Features[Attract Baby Interest]Bright colors and cute model can certainly attract baby’s interest, promoting their visual development, develops baby’s hands-eye coordination and cultivates their imagination and creativity.[DIY Randomly]Contains 399 multi-colored building blocks, your baby can DIY at random, give them endless fun hours of play. Also children …
399PCS 3D Creative Electric Drill Toys Set Drilling Screw Puzzle Toy Kid GiftRead More
Reviews
There are no reviews yet.