48V Wind Generator Controller 500W Wind Turbine Generator Controller
$127.56
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Package list
1x Controller
Specifications
Rated battery voltage:48V
Wind generator braking voltage:60V
Wind generator recover voltage:54V
Protection class:IP67
Precautions
1. Verify that the wind turbine output voltage matches the rated voltage of the battery.
2. Wire in the following order, first connect the positive and negative terminals of the battery, and then connect the three-phase voltage output of the fan.
3. Please carefully connect the battery and the wind turbine to the controller according to the instructions. Connecting the reverse polarity or the wrong position will cause the system to work abnormally and may even cause damage to the system components.
4. Although the controller has taken protective measures against various possible accidents, it is strongly recommended that users strictly abide by the operating procedures to prevent damage to the battery and controller.
Wiring
1. Connect the “+ Inch and “- Inch of the battery to the positive and negative terminals of the battery of the controller.
2. Connect the three-phase output voltage of the wind turbine to the three-phase voltage input terminal of the controller fan.
3. When manual brake is required, short the red thin wire to the positive battery, that is, complete the manual brake function. To cancel this function, just disconnect the thin red wire.
Indicator status
– When the controller green power (BATTERY) indicator is on, it indicates that the battery is connected properly.
– When the controller’s green fan access (WIND) indicator flashes, it indicates that the wind turbine is connected. The speed of the flashing reflects the speed of the fan.
– When the controller red (BRAKE) indicator is on, the battery is fully charged, the wind turbine is automatically braked, or the brake is automatically activated due to overcurrent protection.
Weight | 0.978 kg |
---|
Customers Also Viewed
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820io
$15.30Converter BoardAdd to cart>>>Manual:Click here to openOverviewUSR-ES1 embeds Wiznet’s W5500 chip, which uses hardware logic gates to implement the transport layer and network layer of the TCP/IP protocol stack (such as TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE, etc.), and integrates The data link layer, physical layer, and 32K bytes of on-chip RAM serve as data transceiving buffers. …
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820ioRead More
3pcs TEC1-12715 12V Heat Sink thermoelectric Cooler Peltier Plate Module
$32.04Electronic Accessories & SuppliesAdd to cart40 x 40mm TEC1-12715 12V Heatsink Thermoelectric Cooler Peltier Plate ModuleDescriptionSolid state, vibration free, noise-freeSimple to install and operateThe hot surface need to be good heat sinkSpecificationProduct name:thermoelectric cooler plate moduleModel:TEC1-12715Color:whiteCouples:127Voltage:12VUmax:15.4VImax:15AMax power consumption:231WTmax:70°CQcmax T=0(W):137WSize:40 x 40 x 3.3mmWeight:50gPackage included3 x TEC1-12715 cooler plate module
EQKIT KM-1 DC 6-12V PWM Motor Speed Controller Kit DIY Motor Speed Regulator Set Stepless Speed Control
$8.73Module KitsAdd to cartSpecificationsModel:KM-1Operating voltage:DC 6-12VPCB board size:40 x 40mmCircuit descriptionKM-1 uses PWM (pulse width modulation) to control the speed of the motor, adjust the pulse width duty ratio, so that the speed from zero to the maximum speed stepless speed regulation. The wider the crest width of the control waveform, the faster the motor speed; on the …
20pcs 63V 10000UF 105 High Frequency Temp Electrolytic Capacitor 30mm x 50mm Long Life
$108.62Electronic Accessories & SuppliesAdd to cartSpecificationModel:485622Voltage:63VCapacitance:10000UFTemperature:105→Diameter:30mm / 1.1 inchHeight:50 mm / 2 inchFeaturesLong life, high temperatureHigh-frequency capacitorsPackage included20 x Electrolytic Capacitor
Reviews
There are no reviews yet.