JK11S-100S-5V 10A 0-100S Adjustable ON-OFFf Delay Module Timer Cycle Switch infinite Loop Relay Module
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Voltage:5V DC
Quiescent current:8mA
Operating current:95mA
Trigger:passive switch trigger, response time is 0.03 seconds (the trigger terminal can not access the active signal)
Minimum on-off time:0.2 seconds
Load capacity:10A
Output form:normally open + normally closed
Size:70*20*19mm
Features
– Using industrial-grade single-chip microcomputer to control time, high precision and stable performance;
– Two adjustable resistors are used to adjust the time, and the connection duration and the disconnection time can be independently adjusted;
– The external contact is activated, and the timing is started by shorting the self-reset button. It is also possible to start the countdown by shorting the triggers together to achieve power-on;
– The time range is divided into 0-100 seconds.
Basic working principle
Taking the factory standard setting as an example, the red LED will light when the power is turned on, and the relay is in the off state. When shorted at the trigger end, the module green light is on and immediately enters the working state. Triggering again in the working state will stop working.
In the working state, the relay will pass T1 seconds, break T2 seconds, pass T1 seconds, break T2 seconds… infinite loop. T1 T2 is the length of time the user adjusts with an adjustable resistor.
Instructions
– Power access
The module is connected to the power supply according to the correct power supply voltage and polarity. The red line of the power supply terminal is positive and the black line is negative.
– Trigger line access
The two white lines of the trigger end are connected to a switch, and the module can be started by tapping the switch, and then the switch is stopped by tapping the switch. The trigger switch can be a tact switch, a micro switch, an optocoupler C-E terminal, a relay contact, and the like.
– Normal speed and quick mode settings
The OP1 jumper is used to select normal speed and fast mode, and the shipment defaults to normal speed.
– Loop mode and single mode settings
The OP2 jumper is used to select the loop mode and the single mode, and the shipment defaults to the loop mode.
Cycle mode:After starting, the relay is on-off-on-off-disconnect…, and it is cycled according to the set duration;
Single trigger:After starting, the relay is turned on, and the relay is turned off after T1 duration. (After disconnection, the action ends and waits for trigger again)
Precautions
1. The module power supply is not protected against reverse protection, because it is important to remember that the power supply cannot be connected.
2. The trigger terminal can only be connected to the passive switch, not to the voltage signal. Doing so can damage the module.
3. When the resistance load is connected, no special treatment is needed; when the capacitive load is connected, the relay module is easily damaged by electricity. It is recommended to use the AC contactor derated or the contact current of the motor should be considered within 10A.
Package Included
1 x JK11S-5V 100S Delay Adjustable Multi-function Relay Module
Weight | 0.019 kg |
---|
Customers Also Viewed
5pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5V
$26.35Power Supply ModuleAdd to cartDescriptions3-Cell(3S) VersionInput voltage:DC 4.5V-5.5V(Recommend DC 5V)Charging voltage about:4.05V-5.1VCharging current about:230mA-240mAUSB power protectionShort circuit protection and zero volt battery activationBattery protectionOperating ambient temperature:-40° to +85°Storage temperature:-65° to +125°Size:30x 15 x 4mmNoteThe output voltage cannot be measured with a multimeter without a battery. But can be observed with an oscilloscope.Applicationskids toys carDigital CamerasSolar chargingBluetooth ApplicationsAudio equipmentDigital CameraElectronic …
5pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5VRead More
5Pcs/Pack 5V 1000mA 165*165mm Monocrystalline Solar Panel Cells with Positive&Negative Cables
$85.54Smart Robot & Solar PanelAdd to cartFeaturesProvide you with high conversion rate and incredibly efficient output.Excellent performance even under the weak sunlight.Portable and solid casing.Application:to charge, for home lighting and different kinds of low-power appliances, for science projects, for solar powered water pump, small solar power system, etc.SpecificationsType:Monocrystalline Size:165*165mmCurrent:1000mA Net Weight:about 600g one packPackage Content:5Pcs x Poly Solar PanelVoltage:5VMPN:Does Not ApplyPackage …
Waveshare 1.54 inch ink Screen Module 152×152 Electronic Paper SPI interface Yellow Black and White 3-color Display
$45.91Display ScreenAdd to cartDocumentsSchematic:Click here to openSample tutorial:Click here to openDatasheet:Click here to openGithub:Click here to openFeaturesNo backlight is needed, and the display content of the last screen can be kept for a long time after power offVery low power consumption, basically only consumes power when refreshingSPI control interface, can be connected to Raspberry/Nucleo and other main control …
Geekcreit DIY Creative Electronic Watch Kit 51 Single-chip LED Digital Tube Clock Training Production Kit
$15.30DIY Electronic KitsAdd to cartDescriptionName:LED Electronic Watch KitPower supply:CR2025 3V button battery (available for testing, there are inevitably extra factors causing insufficient power.)Display:LED red digital tube displaySize:52*52*18mmInstallation:the board need to solder yourself and then assembly the caseFunction:You can press the digital tube button when need to wacth time; it will enter the power saving mode automatically after 5 seconds. …
QFN32 QFP32 Converter SMD To DIP Adapter PCB Universal Board
$3.56Expansion Board & ShieldAdd to cartQFN32 QFP32 Converter SMD To DIP Adapter PCB Universal BoardSpecificationDimension:20.25 x 40.64mm / 0.79inch x 1.60inchThickness:1.5mmPanel:FR4DescriptionThe PCB board has two sides.A side for pin pitch size 0.80mm, B side for pin pitch size 0.80mm.It can be used to convert QFN32/QFP32 (600mil width, 2.54mm pin pitch).You can solder filter capacitors or resistors to increase stability and …
QFN32 QFP32 Converter SMD To DIP Adapter PCB Universal BoardRead More
YJ0007 180W Car Stereo Audio Amplifier Power Boost Board Single 12V input Conversion Double 32V Output
$52.41Boost & Buck ModuleAdd to cartDescriptionAll parts and components of this product are original products, unpretentious and pure in quality; using high-quality original parts not only guarantees safety and quality, but also has a long service life, and more importantly, it is a strong guarantee that the actual performance can reach the design goals.Features1. All components are genuine.2. The main …
Reviews
There are no reviews yet.