JK11S-100S-5V 10A 0-100S Adjustable ON-OFFf Delay Module Timer Cycle Switch infinite Loop Relay Module
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Voltage:5V DC
Quiescent current:8mA
Operating current:95mA
Trigger:passive switch trigger, response time is 0.03 seconds (the trigger terminal can not access the active signal)
Minimum on-off time:0.2 seconds
Load capacity:10A
Output form:normally open + normally closed
Size:70*20*19mm
Features
– Using industrial-grade single-chip microcomputer to control time, high precision and stable performance;
– Two adjustable resistors are used to adjust the time, and the connection duration and the disconnection time can be independently adjusted;
– The external contact is activated, and the timing is started by shorting the self-reset button. It is also possible to start the countdown by shorting the triggers together to achieve power-on;
– The time range is divided into 0-100 seconds.
Basic working principle
Taking the factory standard setting as an example, the red LED will light when the power is turned on, and the relay is in the off state. When shorted at the trigger end, the module green light is on and immediately enters the working state. Triggering again in the working state will stop working.
In the working state, the relay will pass T1 seconds, break T2 seconds, pass T1 seconds, break T2 seconds… infinite loop. T1 T2 is the length of time the user adjusts with an adjustable resistor.
Instructions
– Power access
The module is connected to the power supply according to the correct power supply voltage and polarity. The red line of the power supply terminal is positive and the black line is negative.
– Trigger line access
The two white lines of the trigger end are connected to a switch, and the module can be started by tapping the switch, and then the switch is stopped by tapping the switch. The trigger switch can be a tact switch, a micro switch, an optocoupler C-E terminal, a relay contact, and the like.
– Normal speed and quick mode settings
The OP1 jumper is used to select normal speed and fast mode, and the shipment defaults to normal speed.
– Loop mode and single mode settings
The OP2 jumper is used to select the loop mode and the single mode, and the shipment defaults to the loop mode.
Cycle mode:After starting, the relay is on-off-on-off-disconnect…, and it is cycled according to the set duration;
Single trigger:After starting, the relay is turned on, and the relay is turned off after T1 duration. (After disconnection, the action ends and waits for trigger again)
Precautions
1. The module power supply is not protected against reverse protection, because it is important to remember that the power supply cannot be connected.
2. The trigger terminal can only be connected to the passive switch, not to the voltage signal. Doing so can damage the module.
3. When the resistance load is connected, no special treatment is needed; when the capacitive load is connected, the relay module is easily damaged by electricity. It is recommended to use the AC contactor derated or the contact current of the motor should be considered within 10A.
Package Included
1 x JK11S-5V 100S Delay Adjustable Multi-function Relay Module
Weight | 0.019 kg |
---|
Customers Also Viewed
300W Digital Amplifier Speaker Protection Board 2.1 Channel Relay Speaker Protection Module Boot Delay DC Protection
$15.30Relay ModuleAdd to cartFeatures1.With delay and DC protection (default 1.8V control, DC sensitivity can be adjusted)2. This common power DC protection board uses an optocoupler. Since the optocoupler has input and output isolation,3. Electrical signal transmission has the characteristics of unidirectionality, so it has good electrical insulation and anti-interference ability.4. Since the input end of the optocoupler belongs …
AB18 2SA1943/2SC5200 High Power 300W + 300W Dual Channel Class A/B Power Amplifier Board for Sound Speaker DIY
$125.17Amplifier BoardAdd to cartProduct description1. Using Japan imported original brand new 2SA1943/2SC52002. Electrolytic capacitor adopts imported electrolysis to ensure strong continuous power support.3. The resistor uses high-precision resistors, and the main circuit uses high-precision resistors with an accuracy of ÷ 1% to ensure a good signal-to-noise ratio for the whole machine.4. The PCB adopts 1.6mm thick double-sided sheet, …
5pcs DMP-L1 WiFi intelligent Lighting Module Built-in ESP ESP8285 WiFi Chip for Smart Home
$28.82Smart ModuleAdd to cartDescriptionThe core processor of DMP-L1 module adopts industrial chip ESP8285. The chip integrates an enhanced version of the Tensilica’s L106 Diamond Series 32-bit core processor in smaller size packages. ESP8285 has a complete Wi-Fi network function, which can be used independently from the controller. Its built-in cache memory greatly provides CPU performance.DMP-L1 module supports standard …
5pcs DMP-L1 WiFi intelligent Lighting Module Built-in ESP ESP8285 WiFi Chip for Smart HomeRead More
Wareshare 5.5 inch AMOLED HDMI Display Capacitive Touch Screen with Tempered Glass Support for NVIDIA Jetson Nano Raspberry Pi
$229.66Display ScreenAdd to cartDocumentsManual:Click here to openDatasheet:Click here to openSoftwarePanasoni SDFormatterWin32DiskImagerPuTTYOverviewThis product is a universal 5.5-inch HDMI display with 1080≠1920 ultra-clear resolution and a capacitive touch panel. Support for Raspberry Pi and various mini PCs, also as a computer monitor.Features5.5inch AMOLED, 1080×1920 resolution.Toughened glass capacitive touch panel.Supports popular mini PCs such as Raspberry Pi, as well as general …
5pcs 20x20x15mm DIY CPU IC Chip Heat Sink Extruded Cooler Aluminum Heat Sink
$4.36Electronic Accessories & SuppliesAdd to cartFeatureAluminum heat sinks for electronics, computers, electrical facilities, play a cooling effectSpecificationMaterials:AluminumSize:20*20*15mm (L*W*H)Color:SilverQty:5pcsPackage includes5 x CPU IC Chip Aluminum Heat Sink
5Pcs Yellow Backlight 1602 Character LCD Display Module
$24.89Display ScreenAdd to cartDescriptionLCD display module with yellow backlightWide viewing angle and high contrastBuilt-in industry standard HD44780 equivalent LCD controllerCommonly used in:copiers, fax machines, laser printers, industrial test equipment,networking equipment such as routers and storage devicesLCM type:CharactersCan display 2-lines X 16-charactersOperate with 5V DCModule dimension:80mm x 36mm x 12mmViewing area size:64.5mm x 16mmPackage included5 X LCD display module
Bathtub Caddy Bamboo Bath Tub Holder Bathroom Tray Glass Book Reading Rack Stand
$106.76FoamAdd to cartSpecificationMaterial:BambooColor:WoodSize:(L)X(W)X(H)105X22X4cm/41.34inchX8.66inchX1.57inch(appr.)Features1. Constructed from durable bamboo and metal supporting frame in excellent craftsmanship for many years use.2. Varnish processing on surface, lightweight and easy to operate.3. Books can be held with metal rack stably for reading when bathing.4. Books, phone, towl, and food can be placed on it for convenient reach.5. Its length is adjustable between …
Bathtub Caddy Bamboo Bath Tub Holder Bathroom Tray Glass Book Reading Rack StandRead More
Reviews
There are no reviews yet.