XH-W1411 12V 10A Smart Electronics LED Digital thermometer Temperature Controller Switch Module
$16.02
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Temperature range:-55- + 120→
Temperature measurement accuracy:± 0.3→
Resolution:0.1→
Temperature range:-19 ~ 99→
Control accuracy:1→
Temperature probe:NTC10K / B3950 comes standard with 1 meter waterproof probe
Supply voltage:12V
Temperature:-25 ~ 55→ Humidity 20% -85% (non-condensing)
Output Type:10A relay outputs
Size:90*60mm/3.54 Inch*2.36 Inch
Hole size:70*50mm/2.76 Inch*1.96 Inch
Features
– The board and plastic panels fixed column compartment and lock nut
– Connect the power supply according to the drawings and load control line
– By drawing on the chassis opening 70 * 50mm, then tighten the screws after the thermostat embedded Paste Mask
– After power if the temperature in the interval starts immediately output to stop off value
– Start temperature For example, want to control the production of hot water, heated to 60 degrees stop, stop again begin heating to 45 degrees, then the start value should be 45 degrees, 60 degrees is stopped
– Start temperature> stop temperature = cooling mode
– For example, want to control greenhouse cooling, ventilation fans start when higher than 35 degrees, down 32 degrees when you stop, you start value should be set to 35, stop value is set to 32
– SET Function keys / Off button
1. In the boot state press SET 3s can shutdown, shutdown if the power remains off
2. Press SET to power in the off state, after boot if the power remains switched on
3.Short press SET to switch module temperature intermittent operation → → → reservation Power Off Timer (F1-F3 function independently, with the temperature does not matter, do not need to be able to do)
4. Left F-1 intermittent operation mode in minutes start minute, the right to stop minute
5. F-2 hour timer switch to the left, to the right minutes, maximum 99 hours 59 minutes
6. F-3 power appointment hours left, the right minutes, maximum 99 hours 59 minutes
7. Temperature correction:Unplug thermostat hold the SET power plug into the temperature correction function, the screen display –000– can subtract the temperature at temperature before correction on the basis of the maximum range -9.9 to 99,
8.After the calibration is complete:real-time temperature = temperature before correction + correction
9. Press and hold the (Start + -) power-on self-test function into
10.Press and hold (Stop + -) power to restore the factory settings
Reset
1. If errors or confusing settings, press and hold the power button to stop two restore factory settings
2. 88-888-88 display, buzzer flute sound, complete recovery
Package Included
1 x XH-W1411 Smart Electronics LED Digital Thermometer
Weight | 0.053 kg |
---|
Customers Also Viewed
3 Axis GRBL USB Driver offline Controller Control Module LCD Screen w/ Controller Board SD Card for CNC 1610 2418 3018 Wood Router Laser Engraving Machine
$93.14Control BoardAdd to cartDescriptionThis offline controller w/ controller board is designed for the use of Mini CNC router 1610/2418/3018 and even with more advanced function of tool set, limit switch supportive, Laser supportive; Offline and Bluetooth supportive.SpecificationUSB Cable Length:20cmFirmware:GRBL 08, 09, 1.1 and so on Input Voltage:DC 7V- 36VApplicable CNC Router:3 Axis CNC router 1610; 2418; 3018Features1. Support …
20Pcs PS2 Game Joystick Switch Sensor Module
$34.87Other Module BoardAdd to cart20Pcs PS2 Game Joystick Module For Description This is PS2 game joystick module for Lots of robot projects need joystick. This module provides a affordable solution to that. Simply connect to two analog inputs, the robot is at your commands with X,Y control. It also has a switch that is connected to a digital pin. …
Ebyte E07-M1101D-TH 10dBm Spring Antenna 433MHz CC1101 Wireless Transceiver SPI 433mhz RF Module
$9.18Smart ModuleAdd to cartSpecificationsInterface:SPIPower:10dBmDistance:520mSupply voltage:1.9 ~ 3.6V DCFrequency:433MHz(387 ~ 464MHz)RF Parameter:Value:RemarkWorking frequency:387~464 MHz:Default:433MHz (26MHz oscillator)Transmitting power:10 dBm:Max. Power (10mW)Receiving sensitivity:-108 dBm:Air data rate:0.6kbpsAir data rate:0.6k~500kbps:Default:0.6kbpsTest distance:600m:In open and clear air, with maximum power, 5dBi antenna gain, height of 2m, air data rate:0.6kbpsHardware Parameter:Value:RemarkSize15 * 30 mm Without Spring antennaAntenna typeSpring antenna Communication interfaceSPI PackageDIP Electronic parameter:Min.:Typ.:Max.:Unit:ConditionPower supply:1.8:3.3:3.6:VCommunication level:1.8:3.3:3.6:VTransmitting …
Waveshare IS62WV51216BLL SRAM RAM Module Storage Memory Board
$28.42Expansion Board & ShieldAdd to cartFeatureFunction:SRAM IS62WV51216BLL (8M Bit), can be directly connected to the corresponding FSMC interface of the Open series development board, and the external expansion interface supports external expansion of SRAM, LAN, USB HOST, etc.Typical application:SRAM external expansion storageMain resources:IS62WV51216BLL (8M Bit), control interfacePackage includes1 x IS62WV51216BLL SRAM Board
3 Megapixel Optical Zoom Cam Module Fixed Focus 3MP OV3660 Camera Module FOV 79
$15.30Other Module BoardAdd to cart>>>Manual:Click here to openSpecificationsModel No.:HBVCAM-3M1917Model Size:30mm ≠ 25mm ≠ 5.0mm÷0.2MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:FixedObject distance:30CM-infinityResolution:800LW/PH (Center)PCB printing ink:Blackinterface:USB 2.0Power supply:USB bus powersupply voltage:DC 5V÷5%Maximum Power consumption:600WOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvc Sensor:OV3660 (1/5” )Seneor Package:CSP,Bare DieMaximum resolution:2048*1536Sensitivity:670mV /(lux-sec)Pixel Size:1.4┢m x 1.4┢m Maximum Image Transfer …
3 Megapixel Optical Zoom Cam Module Fixed Focus 3MP OV3660 Camera Module FOV 79Read More
Hall Effect Magnetic Sensor Module DC 5V
$4.36Sensor & Detector ModuleAdd to cartDescription This is Hall Effect magnetic sensor module DC 5V for Brand:KEYES Model:KY-003 Magnetic, speed, gap induction Suitable for DIY project Working voltage:DC 5V Material:PCB Feature Small size and high sensitivity. response temperature and good performance. Precision and high reliability 3144 Series Hall principle of Hall effect switch IC, using technology to produce magnetic semiconductor …
Geekcreit Portable Mini Automatic Spot Welding Machine Control Board 12V/5.6V Portable Lithium Battery Spot Welding Circuit Board Accessories
$40.49Driver ModuleAdd to cartInstructions for use of automatic spot welding control board1. Power requirements:In 12V mode, voltage input is 7-15V (12V recommended), in 5.6V capacitor mode, voltage supports 3.7-6V (recommended 5.6V), current requirements:can output actual current 120-360A2. Button function:switch between 1 power level-2 power level-3 power level-4 power level after long press for 3 seconds3. The red light …
Reviews
There are no reviews yet.