XH-W1411 12V 10A Smart Electronics LED Digital thermometer Temperature Controller Switch Module
$16.02
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Temperature range:-55- + 120→
Temperature measurement accuracy:± 0.3→
Resolution:0.1→
Temperature range:-19 ~ 99→
Control accuracy:1→
Temperature probe:NTC10K / B3950 comes standard with 1 meter waterproof probe
Supply voltage:12V
Temperature:-25 ~ 55→ Humidity 20% -85% (non-condensing)
Output Type:10A relay outputs
Size:90*60mm/3.54 Inch*2.36 Inch
Hole size:70*50mm/2.76 Inch*1.96 Inch
Features
– The board and plastic panels fixed column compartment and lock nut
– Connect the power supply according to the drawings and load control line
– By drawing on the chassis opening 70 * 50mm, then tighten the screws after the thermostat embedded Paste Mask
– After power if the temperature in the interval starts immediately output to stop off value
– Start temperature For example, want to control the production of hot water, heated to 60 degrees stop, stop again begin heating to 45 degrees, then the start value should be 45 degrees, 60 degrees is stopped
– Start temperature> stop temperature = cooling mode
– For example, want to control greenhouse cooling, ventilation fans start when higher than 35 degrees, down 32 degrees when you stop, you start value should be set to 35, stop value is set to 32
– SET Function keys / Off button
1. In the boot state press SET 3s can shutdown, shutdown if the power remains off
2. Press SET to power in the off state, after boot if the power remains switched on
3.Short press SET to switch module temperature intermittent operation → → → reservation Power Off Timer (F1-F3 function independently, with the temperature does not matter, do not need to be able to do)
4. Left F-1 intermittent operation mode in minutes start minute, the right to stop minute
5. F-2 hour timer switch to the left, to the right minutes, maximum 99 hours 59 minutes
6. F-3 power appointment hours left, the right minutes, maximum 99 hours 59 minutes
7. Temperature correction:Unplug thermostat hold the SET power plug into the temperature correction function, the screen display –000– can subtract the temperature at temperature before correction on the basis of the maximum range -9.9 to 99,
8.After the calibration is complete:real-time temperature = temperature before correction + correction
9. Press and hold the (Start + -) power-on self-test function into
10.Press and hold (Stop + -) power to restore the factory settings
Reset
1. If errors or confusing settings, press and hold the power button to stop two restore factory settings
2. 88-888-88 display, buzzer flute sound, complete recovery
Package Included
1 x XH-W1411 Smart Electronics LED Digital Thermometer
Weight | 0.053 kg |
---|
Customers Also Viewed
433MHz 100M Wireless Transceiver Module Kit Transmitter + Receiver + 2pcs Copper Spring Antenna
$8.73Smart ModuleAdd to cartDescriptionSTX882 ASK Wireless Remote Control Transmitter ModuleSTX882 is a ASK transmitter module with small size, ultra high power, low harmonics. With high stability, it can be achieved at 50mW power when the voltage is 3.6V, it is the maximum transmitter power module under the the same voltage in the market. Data port of the module …
5V 3.3V FT232RL USB Module To Serial 232 Adapter Download Cable
$10.92Other Module BoardAdd to cart5V 3.3V FT232RL USB Module To Serial 232 Adapter Download Cable ForFeature1. With FT232RL chipset, support 3.3V, 5V2. With over current protection, using 500MA self-restore fuse3. RXD/TXD transceiver communication indicator4. Pin definition:DTR,RXD,TX,VCC,CTS,GNDPackage included1 x USB Module
12V/220V 2CH HIFI Audio Stereo Power Amplifier Bass bluetooth FM Radio Car Home
$74.91Solar CollectorsAdd to cartSpecificationsColo:BlackModel:G30Input voltage:AC 220V/ DC12V(in car)Plug:EU plug(sent with an adapter according to your country)bluetooth:SupportRMS power:18W x2Peak power:45W x2Load impedance:4-16ΩSNR:85 dbFM frequency:87.5-108MHzDistoration rate:0.05%Frequency:10Hz-20KHzSize:Approx. 19×12.5×4.5cm/ 7.48×4.92×1.77inchFeatures-Mini HIFI digital bluetooth audio power amplifier.-TF Card, AUX, U disk, MP3 format play, support bluetooth wireless connection.-Supports FM stereo radio.-With treble, bass, and volume control, very easy to use.-Low distortion supplies a …
12V/220V 2CH HIFI Audio Stereo Power Amplifier Bass bluetooth FM Radio Car HomeRead More
KY-011 5mm 2 Color Red and Green LED Common Cathode Module Board for Arduno Diy Starter Kit 2-color KY011
$4.36LED BoardAdd to cartSpecificationsColor:Green + RedDiameter:5mmPackage Type:DiffusionVoltage:2.0-2.5vCurrent:10mAViewing angle:150 degreeWavelength:571 +644 nmLuminous intensity (MCD):20-40; 40-80Stent type:long-leggedPackage Included1 x KY-011 Two Color Red and Green LED Module for Arduno
1000Pcs 5 Colors 3mm F3 Ultra Bright Round LED Diode Kit
$19.67Electronic Accessories & SuppliesAdd to cart1000Pcs 5 Colors 3mm F3 Ultra Bright Round LED Diode Kit Red / Green / Blue / White / YellowParameterWorking current:20 (mA)Working voltage:Red:1.9V-2.1V Yellow:1.9V-2.1V Blue:3.0V-3.2V Green:3.0V-3.2V White:3.0V-3.2VMCD:Red:1000-1500 Yellow:700-900 Blue:2000-3000 Green:7000-9000 White:6000-8000Wave length:Red:620-625 Yellow:588-590 Blue:455-465 Green:567-570 White:Color temperature 8000Each colors 200Pcs, total 1000PcsPackage included2 x 500Pcs 5 Colors LED Diode kit
4 Digit LED Display Tube 7 Segments TM1637 50x19mm Blue Clock Display Colon Module
$13.11Display ScreenAdd to cartFeatureThis is a basic 4-digit 7-segment display module.The display features double points in midle. The decimal point per digit not active.Module connecting to digital I/O on 2 pins.For Arduino use library:TM1637.hPackage includes1 x LED Display TubeSketch include inchTM1637.hinch // include the TM1637 libraryTM1637 display(2, 3);// // initialize the library for pins 2, 3void setup()void loop()
DIY LED Light String Kit Part for Lego 10267 House Model Building Gingerbread Flash
$69.97DIY Electronic KitsAdd to cartSpecification1. Name:LED Light Set2. Model:D858093. Material:Plastic4. Power:Less Than 5V5. Fitment:For Lego 10267Note1. LED Light Set Only. Toy is not included.2. Manual installtion. It needs to be assembled by yourself.Package Included10 x 15cm Bit Light(Warm White)1 x 15cm Enhance Bit Light(Warm White)4 x 30cm Flashing Bit Light(Red)4 x 30cm Flashing Bit Light(White)1 x Multi Colour Light …
DIY LED Light String Kit Part for Lego 10267 House Model Building Gingerbread FlashRead More
Reviews
There are no reviews yet.