PAM8403 DC5V 2x3W Digital Amplifier Module Dual Channel Power Stereo Amplifier Board
$4.60
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Supply voltage:DC 2V-5.5V
Distortion rate:1 (%)
Signal to noise ratio:90 (db)
Input impedance:2
Output impedance:4 (Ω)
Rated power:3 (W)
Frequency response:100Hz-15KHz
Efficiency:>90%
Number of channels:two channels
PCB Size:31x19mm
Note
1. The power supply voltage must not exceed the limit voltage of 5.5V. It is forbidden to reverse the power supply to avoid permanent damage to the chip.
2. This amplifier chip has built-in high-gain electronic volume control. Please adjust the volume to the middle position during debugging.
3. The maximum instantaneous dynamic current of this power amplifier board can reach 1.2A. It is strongly recommended to use a voltage of 5V and a power supply with a good filtering performance of 1A or more.
4. The speaker must be properly installed. Do not test directly with the speaker without the box, otherwise the ideal effect will not be achieved.
5. The output of this circuit is the BTL drive mode of the coms tube. The negative poles of the left and right speakers cannot be connected together, that is, the four lines connected to the speaker are completely independent and are not allowed to be shared.
Package Included
1 x 3W Stereo Amplifier Board
Weight | 0.006 kg |
---|
Customers Also Viewed
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with Cable
$11.26Sensor & Detector ModuleAdd to cartFeatures– Can receive standard 38KHz remote control signals by means of programming can decode the remote control signals– Strong ability to resist electromagnetic interference and light– Widely used in stereo, TV, set-top boxes, digital photo frame, car stereo, remote control toys, satellite receivers, hard disk players, air conditioner, heater, electric fan, lighting and other home …
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with CableRead More
600V 45A 3 Position Terminal Block Barrier Strip Dual Row Screw Block Covered W/ Removable Clear Plastic insulating Cover
$16.19Terminal BlocksAdd to cartSpecificationModel:TB4503Type:Terminal block Working frequency:High frequencyInterface type:AC/DCRated current:45ARated voltage:600VConductor cross section:0.5-4mm2Number of pin:6Number of bits:3Contact material:IronSize:70mm x 38mm x 24mmFeature:–Moistureproof–High quality guides,durable–High quality thickened conductive parts–High quality iron screw with high strength–Dust proof transparent plastic protective coverPackage Included1 x Terminal block
5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V inverter
$26.31Smart ModuleAdd to cart5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V Inverter For 10 Inch To 22 Inch ScreenFeatureVoltage:10V ~ 28VCable:300mm(L) / 6 pinSize:122 x 27mm ( L x W )Interface:double light small interfaceInterface definition:1. VCC 2. GND 3. NULL 4. NULL 5. ON/OFFPackage included5 x 2 lamp backlight universal laptop LCD CCFL inverter 10V-28V5 x Cable
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier Board
$20.90Amplifier BoardAdd to cartFeatures1. Power filter function is through the power line access power filter,get a specific frequency of the power signal, or eliminate a specific frequency power signal. By using this feature of the power filter, a square wave complex or complex noise passing through the power filter can be converted into a sine wave of a …
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier BoardRead More
5pcs EQKIT TDL-555 Touch Delay LED Light DIY Kit Touch Delay Lamp Electronic Parts Production Kit DC 5V 3s to 130s Adjustable
$10.12DIY Electronic KitsAdd to cartFunction1. Connect Power,Red LED ON2. Touch and then start to delay and Red LED OFF and 5pcs White LED ON at the same time3. Red LED ON and White LED OFF after delay4. Delay can be adjust by potentiometer for 3-130 secondPackage included5 x EQKIT® TDL-555 Touch Delay LED Light DIY Kit
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4
$22.95Raspberry Pi & Orange PiAdd to cartOverviewThis is a universal driver board for e-Paper panels, can be used to drive various SPI interface e-Paper from Waveshare.FeaturesStandard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson NanoSPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.Onboard voltage translator, compatible with 3.3V/5V MCUsComes with development resources and manual (examples …
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4Read More
Reviews
There are no reviews yet.