W3003 12V/24V/220V Microcomputer Digital Display intelligent Temperature Controller Electronic for Burner Fuel Machine Controller
$15.75
Voltage 12V / Voltage 24V /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Supply voltage:12V/24V/220V
Load power:120/240/1500W
Temperature control range:0-450 °C
Temperature range:0-450 °C
Temperature control accuracy:0.1 °C
Measurement input:k-type thermocouple
Output type:direct output
Output capacity:up to 10A
Mounting aperture:73mm
Aperture:4mm
Size:60*45*31mm
Introduction
Setting parameter table
Code:Description:Setting range:Factory settings
P0:Starting temperature:0-450→:00
P1:Stop temperature:0-450→:00
P2:Temperature correction:-10-10→:0
P3:Delayed start:0-10 min:0
– P0 sets the starting temperature
Press the setup button to enter the internal menu. The default display is T0. Press the setup button again to set the desired startup temperature via the up and down buttons.
– P1 sets the stop temperature
b Set the button to enter the internal menu, the digital display is P0, switch to P1 through the up and down buttons, press the setting button again, and set the required stop temperature through the up and down buttons.
– P2 set temperature correction
In the same way, enter the internal menu, switch to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by the up and down buttons. In the setting, if the detected temperature value is 0.5 °C larger than the actual temperature value, then the calibration temperature to be set is -0.5 °C. If the inspection temperature value is 1 °C smaller than the actual temperature value, the calibration temperature to be set is 1 °C. Temperature + – Correction temperature = actual temperature.
– P3 sets delayed start
In the same way, enter the internal menu, switch to P3 by the up and down keys, press the setting button again, and set the required delay time by the up and down buttons (the unit is minute > delay start is generally used for compressor refrigeration, if needed for refrigerator freezer, This value needs to be set. The value of the compressor back pressure is set to 3-6 minutes. If you are not using it to control the compressor or do not need the delay function, skip this item.
Heating mode setting method
Setting method:starting temperature
Setting method
Press the SET button to enter the internal menu, set the startup temperature by setting the P0 value, and set the stop temperature by setting the P1 value.
Use Cases
Control the water heater, heat it to 50 °C to stop, and the temperature will fall back to 40 °C to start heating again. How to set it
Step 1:Determine the working mode as heating mode, starting temperature
Step 2:Press the SET button to enter the internal menu, select P0 and press the SET button to set the P0 value to 40 °C.
Step 3:Press the SET button to enter the internal menu, select P1 and press the SET button to set the P1 value to 50 °C.
Cooling mode setting mode
Setting method:Start temperature > stop temperature (program automatically determines the working mode is cooling mode)
The setting method is as above.
Note
When setting the heating mode, if you accidentally set the set temperature value upside down, the output indicator will not light, the load will not work. If the above situation occurs after the setting is completed, you can check whether the set temperature value is reversed. .
Package Included
1 x Digital Display Intelligent Temperature Controller
Weight | 0.066 kg |
---|
Customers Also Viewed
13S 13 Series SANYUAN 48V 15A Electric Car Special Lithium Battery Protection Board for 3.7V Battery
$14.50Battery Protection ModuleAdd to cartSpecificationBrand:Changfa (Digital)Model:CF-JW4815A-AProduct name:13 series SANYUAN 48V 15A Lithium Battery Protection Plate Discharge current:15ACharging current (same port):15AMain circuit conduction internal resistance:20MRCharging voltage:54.6VShort circuit protection:300USWorking temperature range:-30→~+80→Working power consumption:40UAApplicable battery:3.7VOvercharge:4.25÷0.025VOver discharge:2.80÷0.08VProduct size:60 *33 *9mmPackage included1 x Lithium Battery Protection Panel
LILYGO T-Solar Development Board ASR6505 integrates SX1262LORa Module Solar Power Supply interface
$32.97Motherboard & Development BoardAdd to cartIntroductionT-Solar uses the new lora system chip ASR6505The ASR6505 is based on the STM 8-bit MCU and SX1262 SiP chip, which is more cost-effective than the 32-bit MCU!One of the biggest features of T-Solar is:solar powered design!The solar power supply interface is reserved on the board, which can be directly connected to the 5.5v-7.5v solar …
Geekcreit L9110S H-bridge Dual DC Stepper Motor Driver Board Stepper Motor Module L9110
$6.55Driver ModuleAdd to cartIntroductionTwo the L9110S motor control chip OnboardThe module can simultaneously drive two DC motors or a 4-wire 2-phase stepper motorThe module input voltage:2.5-12VThe 800mA continuous current output capability per channelFeature1. Low static work current2. Power supply voltage:DC2.5-12V3. Each channel has 800mA continuous current output4. Low saturation pressure drop5. TTL/CMOS output level compatible can be connected …
Geekcreit L9110S H-bridge Dual DC Stepper Motor Driver Board Stepper Motor Module L9110Read More
YAHBOOM 5M 1080P OV5647 Sensor Wide Angle Camera Module for Raspberry Pi 4B/3B+/3B
$20.64Raspberry Pi & Orange PiAdd to cartSpecificationCamera interface:CSIPixels:5 MPPhotosensitive chip:OV5647Static image resolution:2592*1944Angle:65 degreesSize:25 mm * 24 mm * 9 mmVideo:1080P30, 720P60, 640* 480p60/90Length of Camera Cable:15 cmPackage includes1 x Camera1 x 15cm Camera CableDocumentsYahboom Raspberry Pi Wide-Angle Camera Details picture:
20pcs Black Protective ABS Case Support Cooling Fan for Raspberry Pi 4 Model B
$133.85Raspberry Pi & Orange PiAdd to cartOverviewThis is a new design ABS case to protect your Raspberry Pi 4 Model B computer, and it is only comepatible with your Raspberry Pi 4 Model B, not support other versions. Also support install a dc 5v cooling fan. The GPIO pin interface is available to us if you do not install the cooling …
20pcs Black Protective ABS Case Support Cooling Fan for Raspberry Pi 4 Model BRead More
Robotdyn Nano V3 Ethernet Shield W5500 (V2) WizNet W5500 TCP/IP 80MHz
$28.42Expansion Board & ShieldAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.FeatureIf you’re looking to build a network-connected device with Nano is the best solution for you!Ethernet Shield W5500 features the Ethernet controller based on WizNet W5500 TCP/IP. WizNet W5500 is a TCP/IP …
Robotdyn Nano V3 Ethernet Shield W5500 (V2) WizNet W5500 TCP/IP 80MHzRead More
TPA3251D2 Digital Class D High Power Amplifier Board 175W+175W DC24-36V
$119.95Amplifier BoardAdd to cartIntroductionTPA3251D2 is a high-performance class D power amplifier, which has class D efficiency and can bring true high-end sound quality. The device features advanced integrated feedback design and proprietary high-speed gate driver error correction function. This technology allows the device to maintain ultra-low distortion throughout the audio frequency band while exhibiting perfect sound quality. The …
TPA3251D2 Digital Class D High Power Amplifier Board 175W+175W DC24-36VRead More
Reviews
There are no reviews yet.