W3003 12V/24V/220V Microcomputer Digital Display intelligent Temperature Controller Electronic for Burner Fuel Machine Controller
$15.75
Voltage 12V / Voltage 24V /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specifications
Supply voltage:12V/24V/220V
Load power:120/240/1500W
Temperature control range:0-450 °C
Temperature range:0-450 °C
Temperature control accuracy:0.1 °C
Measurement input:k-type thermocouple
Output type:direct output
Output capacity:up to 10A
Mounting aperture:73mm
Aperture:4mm
Size:60*45*31mm
Introduction
Setting parameter table
Code:Description:Setting range:Factory settings
P0:Starting temperature:0-450→:00
P1:Stop temperature:0-450→:00
P2:Temperature correction:-10-10→:0
P3:Delayed start:0-10 min:0
– P0 sets the starting temperature
Press the setup button to enter the internal menu. The default display is T0. Press the setup button again to set the desired startup temperature via the up and down buttons.
– P1 sets the stop temperature
b Set the button to enter the internal menu, the digital display is P0, switch to P1 through the up and down buttons, press the setting button again, and set the required stop temperature through the up and down buttons.
– P2 set temperature correction
In the same way, enter the internal menu, switch to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by the up and down buttons. In the setting, if the detected temperature value is 0.5 °C larger than the actual temperature value, then the calibration temperature to be set is -0.5 °C. If the inspection temperature value is 1 °C smaller than the actual temperature value, the calibration temperature to be set is 1 °C. Temperature + – Correction temperature = actual temperature.
– P3 sets delayed start
In the same way, enter the internal menu, switch to P3 by the up and down keys, press the setting button again, and set the required delay time by the up and down buttons (the unit is minute > delay start is generally used for compressor refrigeration, if needed for refrigerator freezer, This value needs to be set. The value of the compressor back pressure is set to 3-6 minutes. If you are not using it to control the compressor or do not need the delay function, skip this item.
Heating mode setting method
Setting method:starting temperature
Setting method
Press the SET button to enter the internal menu, set the startup temperature by setting the P0 value, and set the stop temperature by setting the P1 value.
Use Cases
Control the water heater, heat it to 50 °C to stop, and the temperature will fall back to 40 °C to start heating again. How to set it
Step 1:Determine the working mode as heating mode, starting temperature
Step 2:Press the SET button to enter the internal menu, select P0 and press the SET button to set the P0 value to 40 °C.
Step 3:Press the SET button to enter the internal menu, select P1 and press the SET button to set the P1 value to 50 °C.
Cooling mode setting mode
Setting method:Start temperature > stop temperature (program automatically determines the working mode is cooling mode)
The setting method is as above.
Note
When setting the heating mode, if you accidentally set the set temperature value upside down, the output indicator will not light, the load will not work. If the above situation occurs after the setting is completed, you can check whether the set temperature value is reversed. .
Package Included
1 x Digital Display Intelligent Temperature Controller
Weight | 0.066 kg |
---|
Customers Also Viewed
OpenMV OpenMV3 4 2 Camera Module M7 H7 LCD Expansion Board Display Screen Module
$50.02Display ScreenAdd to cartnullFeatureThe LCD Shield gives your OpenMV Cam the ability to display what it sees on-the-go while not connected to your computer. It features a 1.8inch 128×160 16-bpp (RGB565) TFT LCD display with a controllable backlight. Your OpenMV Cam’s firmware has built-in support for controlling the LCD Shield using the LCD module.ApplicationsThe LCD Shield is great …
OpenMV OpenMV3 4 2 Camera Module M7 H7 LCD Expansion Board Display Screen ModuleRead More
3pcs MFRC-522 RC522 RFID RF IC Card Reader Sensor Module Solder 8P Socket
$10.96Sensor & Detector ModuleAdd to cartIntroduction to the RFID moduleThe MF522-AN module adopts MFRC522 original chip design card reader circuit, which is easy to use and low in cost. It is suitable for users of advanced applications such as device development and card reader development, and users who need to design/produce RF card terminals. This module can be directly loaded …
3pcs MFRC-522 RC522 RFID RF IC Card Reader Sensor Module Solder 8P SocketRead More
Transparent Acrylic Sheet Housing Module Case for DSO138 Oscilloscope
$17.48DIY Electronic KitsAdd to cartFeatureThis product is for DSO138 Oscilloscope only. (Product ID:984002, 969762)Color:TransparentMaterial:AcrylicInstallation size:12.7 x 8.7 x 2.6 (L*W*H)Note:Package does not includes the DSO138 Oscilloscope.Instruction:Click to openPackage includes1 x DSO138 Transparent Acrylic Sheet
20Pcs 3V 650nM 5mW Line Laser Diode Module
$41.34Module ComponentsAdd to cartDescriptionSpot mode:line(Continuous output)Dimensions:diameter 9mm x length 23mmLaser working life:5000-10000 hours or moreLaser wavelength:650nmOutput power:5mWOperating voltage:DC3VWorking current:16mA ~ 20mAWorking temperature:-36 → ~ 65 →Storage temperature:-36 → ~ 65 →Level:sub-industrial gradeColor:red lightMaterial:brassApplication(1) industrial grade:can be used for equipment, health care, military, Kam pseudo security, stage lighting, tools, U disk, mobile phone, projection teaching flip pen, warm measuring …
MMDVM Open-Source Multi-Mode Digital Voice Modem DIY Kit Expansion Board for Raspberry Pi
$103.03Raspberry Pi & Orange PiAdd to cartDescription– This board could cooperate Raspberry Pi , Orange Pi, a variety of school development board to use.– Board has been applied in the GM300 GM3188 3688 950I 338 Vitex DR-1X, other types of repeaters and car stations need to be studied yourself.– The MMDVM is intended to be an open-source Multi-Mode Digital Voice Modem,which …
MMDVM Open-Source Multi-Mode Digital Voice Modem DIY Kit Expansion Board for Raspberry PiRead More
3Pcs 5V-30V DC PWM Speed Controller Mini Electrical Motor Control Switch LED Dimmer Module
$10.04Other Module BoardAdd to cartFeaturePWM DC motor speed controller is a very safe product.When the situation is overcurrent, it will disconnect by itself. after cooling off a few seconds, the fuse will recovery automatically.With high voltage and high current resettable fuseMini but usefulSpecificationOperating voltage:DC 5-30VControl power:90W (maximum)Quiescent current:0.015A (standby)PWM duty cycle:1% -100%PWM frequency:10khzSize:29mm*23mm (excluding handles)Total height:15mmKnob color:Send randomlyPackage included3 …
3Pcs 5V-30V DC PWM Speed Controller Mini Electrical Motor Control Switch LED Dimmer ModuleRead More
Reviews
There are no reviews yet.