ZB2L3 18650 Battery Capacity Tester External Load Discharge Type 1.2-12V Tester with 2 7.5 Resistors
$15.30
Type With 2*5W+1*50W Resistor / Type With 1*50W Resistor / Type With 2*5W Resistor /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Power supply voltage:DC4.5-6V (micro USB interface)
Working current:no more than 70mA
Discharge voltage:1.00V-15.00V resolution 0.01V
Termination voltage range:0.5-11.0V
Support current through:maximum 3.000A resolution 0.001A
Maximum voltage measurement error:1% + 0.02V
Maximum current measurement error:1.2%+-0.002A
The highest battery capacity range:9999Ah (1Ah=1000mAh). The larger value is switched by the decimal point shift. When it is lower than 10Ah, it is displayed as X.XXX, and when it is above 10Ah, it is displayed as XX.XX, and so on.
Board size:50mmX37mm
Finished product size:50mmX37mmX17mm (length X width X height maximum position size, including copper foot height)
Board and accessories weight:single board 28g (including copper column), two 5W ceramic resistor 9g, 50W resistance about 27g (including line)
Note
In order to improve the voltage measurement accuracy, this circuit specially designed the DC offset. When the terminal is not connected, it will display a small voltage, which does not affect the actual measurement. If you short-circuit the input terminal (absolute 0V), it will display 0. . If you want to understand the principle, you can check the superposition theorem in electrical engineering.
During the use of resistance discharge, the resistance load will be severely heated, please pay attention to safety! 50W aluminum shell resistor (has been welded a high temperature wire), please install it on the metal plate!
Instructions
1. The battery under test should be fully charged first.
2. Connect the positive pole of the battery under test to the positive input, the negative pole to the input negative pole, and the reverse polarity (the reverse connection with the load may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (not available for desktop or notebook USB), and the battery voltage is displayed.
3. To start the test directly, just press the “OK Inch button, the tester can automatically set the appropriate termination voltage according to the battery full charge voltage, and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to press the inch+inch or inch-inch button to modify the battery voltage display state, the termination voltage display is P beginning, the latter represents the voltage value, the resolution is 0.1V, after setting, press inchOKinch inchstart testing.
4. After the test starts, the tester will turn on the electronic switch that controls the load. The test process data display will be displayed between the discharge capacity (Ah), the current discharge current (A) and the battery voltage (V). When the battery voltage reaches the set termination voltage, the tester cuts off the load control switch, and the display data stays on the capacity (Ah) and flashes rapidly with the corresponding indicator light. The capacity displayed at this time is the actual discharge capacity of the battery. “OK Inch can terminate the flashing to make the data display stably. Press the “OK Inch button again to return to the power-on state and replace the battery test.
Error code and meaning
Err1:Battery voltage is higher than 15V
Err2:Battery voltage is lower than the set termination voltage
Err3:The battery cannot withstand the load discharge current or the line internal resistance is too large
Err4:The current is too large (current exceeds 3.1A)
Err5:Improper use or wiring error has caused the device to burn out and cannot be used (current sampling or control switch MOS burned)
Secondary calibration operation (after self-running calibration, it means to give up the warranty)
Press and hold the three buttons at the same time to power on the tester, enter the calibration mode, first display the number of calibration records and then enter the official calibration sampling program display 0u0A, then short-circuit the input positive and negative, then press the inchOKinch button to complete the display J10u, Apply 10.00V standard DC voltage between the input positive and negative poles, then press the “OK Inch button, then display J2.0A, apply 2.0A constant DC current to the output negative pole (inflow direction) and input negative pole (outflow direction) and press Move the “OK Inch button to complete the calibration. The tester pre-audits the calibration data. If the calibration data is reliable, it will display 4 calibration numbers and then exit. If the pre-audit considers the data to be unreliable, the data will be discarded.
Package includes
1 x Tester
1/2/3 x Resistor (optional)
Weight | 0.08 kg |
---|
Customers Also Viewed
3pcs L298N Motor Driver Module 4 Chaneel Motor Drive Smart Car Module
$41.54Driver ModuleAdd to cartDescriptionThe four channel L298N motor drive module integrates two L298N chips and can drive four DC motors to realize the control of forward and backward rotation and motor speed. The module is equipped with LM2596S step-down chip. If the motor with 7V voltage or more is driven, 5V power can be output to the control …
3pcs L298N Motor Driver Module 4 Chaneel Motor Drive Smart Car ModuleRead More
Geekcreit D1 Mini ESP32 ESP-32 WiFi+bluetooth internet of Things Development Board Based ESP8266 Module
$21.86Motherboard & Development BoardAdd to cartMore informations:https://github.com/LilyGO/ESP32-MINI-32-V2.0DescriptionThis is D1 Mini ESP32 ESP-32 WiFi+bluetooth Internet Of Things Development Board.Use exampleit can also match the next productPackage included4 x Long female pins4 x short female pins4 x Normal pins1 x mini D1 ESP32
AF1020 Dust-proof Probe Super-stable Pipe-type Current-type Temperature and Humidity Transmitter Temperature Senor Humidity Sensor
$176.16Solar CollectorsAdd to cartSpecificationModel:AF1020 Type Temperature and Humidity TransmitterTemperature measurement range:- 40 ~+80 (℃)Measurement accuracy:+-0.5 (℃)Working Voltage 15-36 (V)Humidity accuracy:+-3% RHHumidity measurement range:0-99.9% RHCurrent output:4-20 m AInstructions1. Power cord positive DC18~36V (red wire)2. Power ground wire GND (black wire)3. Humidity current output 4~20MA (yellow line)4. Temperature current output 4~20MA (white line)Installation sequence1. Connect the red, black, yellow and …
3Pcs 5M Meter thermometer Electronic Digital Display FY10 Embedded thermometer indoor and Outdoor Temperature Measurement
$20.72Test & Measuring ModuleAdd to cartFunction introductionOverall size:48*28*15mmInserted hole size:46*27mmLCD temperature display-50→ to 110→ temperature measurement, 0.1 degree resolution.C and F display versions are availableStandard 0.8m waterproof probeCable length:5 meterPackage includes3 x Thermometer
Peacefair PZEM-028 AC Digital Multifunction Meter Voltmeter Ammeter 0~100A/400V Power Factor Meter
$27.97Electronic Accessories & SuppliesAdd to cartError adjustmentThe product is 100% calibrated before leaving the factory, and the user can also manually adjust the error by himself. The method is as followsStep 1:Long press the button (about 3 seconds) until the digital digit on the screen flashes, then release the button;Step 2:Digital flashing means entering the error adjustment state, the digits …
3pcs 433MHz RF Wireless Receiver Module Transmitter kit + 2PCS RF Spring Antenna OPEN-SMART for Arduino – products that work with official for Arduino boards
$12.11Smart ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionThe kit includes one pair of transmitter and receiver modules and one pair of spring antennas for increasing the communication distance. And the frequency is 433MHz. It is very popular for remote …
10pcs DC 3.7-6V To 400KV Boost Step Up Power Module High Voltage Generator
$55.81Power Supply ModuleAdd to cartFeatureThe high-voltage module uses the principle Tesla coil is made of high-voltage pulse output voltage current, small size, high efficiency, simple external circuit(just plug in the switch, the battery can be) discharge intensity violent.SpecificationModel:MC-105Volume:Length 65mm Diameter 24mm, Diameter of cut surface 22mmVoltage:Input DC3.7-6V, output DC200-400KVCurrent:Input 4A, output 0.5ALength:Input 10 cm or so, the output is …
10pcs DC 3.7-6V To 400KV Boost Step Up Power Module High Voltage GeneratorRead More
Reviews
There are no reviews yet.