ZB2L3 18650 Battery Capacity Tester External Load Discharge Type 1.2-12V Tester with 2 7.5 Resistors
$15.30
Type With 2*5W+1*50W Resistor / Type With 1*50W Resistor / Type With 2*5W Resistor /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Power supply voltage:DC4.5-6V (micro USB interface)
Working current:no more than 70mA
Discharge voltage:1.00V-15.00V resolution 0.01V
Termination voltage range:0.5-11.0V
Support current through:maximum 3.000A resolution 0.001A
Maximum voltage measurement error:1% + 0.02V
Maximum current measurement error:1.2%+-0.002A
The highest battery capacity range:9999Ah (1Ah=1000mAh). The larger value is switched by the decimal point shift. When it is lower than 10Ah, it is displayed as X.XXX, and when it is above 10Ah, it is displayed as XX.XX, and so on.
Board size:50mmX37mm
Finished product size:50mmX37mmX17mm (length X width X height maximum position size, including copper foot height)
Board and accessories weight:single board 28g (including copper column), two 5W ceramic resistor 9g, 50W resistance about 27g (including line)
Note
In order to improve the voltage measurement accuracy, this circuit specially designed the DC offset. When the terminal is not connected, it will display a small voltage, which does not affect the actual measurement. If you short-circuit the input terminal (absolute 0V), it will display 0. . If you want to understand the principle, you can check the superposition theorem in electrical engineering.
During the use of resistance discharge, the resistance load will be severely heated, please pay attention to safety! 50W aluminum shell resistor (has been welded a high temperature wire), please install it on the metal plate!
Instructions
1. The battery under test should be fully charged first.
2. Connect the positive pole of the battery under test to the positive input, the negative pole to the input negative pole, and the reverse polarity (the reverse connection with the load may damage the circuit)! Connect the load to the output positive and output negative, and give the tester micro USB working power (not available for desktop or notebook USB), and the battery voltage is displayed.
3. To start the test directly, just press the “OK Inch button, the tester can automatically set the appropriate termination voltage according to the battery full charge voltage, and will flash the display 3 times to start the test. Need to manually set the termination voltage only need to press the inch+inch or inch-inch button to modify the battery voltage display state, the termination voltage display is P beginning, the latter represents the voltage value, the resolution is 0.1V, after setting, press inchOKinch inchstart testing.
4. After the test starts, the tester will turn on the electronic switch that controls the load. The test process data display will be displayed between the discharge capacity (Ah), the current discharge current (A) and the battery voltage (V). When the battery voltage reaches the set termination voltage, the tester cuts off the load control switch, and the display data stays on the capacity (Ah) and flashes rapidly with the corresponding indicator light. The capacity displayed at this time is the actual discharge capacity of the battery. “OK Inch can terminate the flashing to make the data display stably. Press the “OK Inch button again to return to the power-on state and replace the battery test.
Error code and meaning
Err1:Battery voltage is higher than 15V
Err2:Battery voltage is lower than the set termination voltage
Err3:The battery cannot withstand the load discharge current or the line internal resistance is too large
Err4:The current is too large (current exceeds 3.1A)
Err5:Improper use or wiring error has caused the device to burn out and cannot be used (current sampling or control switch MOS burned)
Secondary calibration operation (after self-running calibration, it means to give up the warranty)
Press and hold the three buttons at the same time to power on the tester, enter the calibration mode, first display the number of calibration records and then enter the official calibration sampling program display 0u0A, then short-circuit the input positive and negative, then press the inchOKinch button to complete the display J10u, Apply 10.00V standard DC voltage between the input positive and negative poles, then press the “OK Inch button, then display J2.0A, apply 2.0A constant DC current to the output negative pole (inflow direction) and input negative pole (outflow direction) and press Move the “OK Inch button to complete the calibration. The tester pre-audits the calibration data. If the calibration data is reliable, it will display 4 calibration numbers and then exit. If the pre-audit considers the data to be unreliable, the data will be discarded.
Package includes
1 x Tester
1/2/3 x Resistor (optional)
Weight | 0.08 kg |
---|
Customers Also Viewed
3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor Module
$24.62Sensor & Detector ModuleAdd to cart3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor ModuleDescriptionCJMCU-219 module is a with I2C interface Bidirectional current / power monitor integrated circuit (IC), and further expand the energy-saving electronic products TI camp. INA219 with the industry’s highest accuracy and smallest size, not only to monitor the voltage drop across a shunt resistor on …
3Pcs CJMCU-219 INA219 I2C Bi-directional Current / Power Monitor Sensor ModuleRead More
GDCPH 16V83F Super Farah Capacitor Automotive Electronic Rectifier 2.7v500F Screw Hole Large Capacity Capacitor
$90.34Electronic Accessories & SuppliesAdd to cartDescriptionThis product can be used in electronic devices such as:RAM, smart three-meter, motor drive, clock circuit, toys, CMOS power failure protection, digital camera, hand-cranked rechargeable flashlight, PDA and other fields as a backup power supply.SpecificationBrand:GDCPHModel:16V83FCapacity:83FRated voltage:16 VSize:231*35*65mmPitch:7mmPackage included1 x capacitor
5pcs PWM DC Motor Governor 5V-16V 10A Speed Switch LED Dimmer Speed Controller
$22.64Motor PWM Speed ControllerAdd to cartParameterMaximum voltage:16VMinimum voltage:5VContinuous current:10AShort circuit maximum current:20A (less than 10 seconds)Speed control mode:PWM stepless speed regulation, can also be used to adjust the lightControl mode:speed control potentiometer (clockwise open, continue to rotate clockwise from 1% to 99%)Duty cycle:0%-99% (0% position is the leftmost state of the potentiometer).When the current is on, 0.002A (there is no …
5pcs PWM DC Motor Governor 5V-16V 10A Speed Switch LED Dimmer Speed ControllerRead More
3pcs 7W 9W 12W 15W LED Non Isolated Modulation Light External Driver Power Supply AC90-265V Constant Current Thyristor Dimming Module
$17.33Driver ModuleAdd to cartSpecificationsInput voltage:AC90-265VOutput voltage:DC21-48VOutput current:300mA(adjustable)Product size:68*34*22mmWorking temperature:Ta:50 TC:75Efficiency:≥80%Power factor:0.6Product application:spotlight PAR light / bulb light / candle light / etc.Package Included3 x 7W 9W 12W 15W LED Non Isolated Modulation Light External Driver
5Set Mini Emergency Hand-cranked Dynamotor Charger Portable Hand-cranked Generator 3V 5V for Diy Electronic Production with Clip Lines
$37.08Electronic Accessories & SuppliesAdd to cartDescriptionUnderstand the gear’s speed-increasing transmission conversion and the principle of electric energy generation, and cultivate the manual and brain skills, which is very suitable for manual classes in schools or for adults and children to play together!When shaking slowly for one second or more, the generating voltage can easily reach 3V, and it is easy …
APPJ Single End 6J1 + FU32 Tube Amplifier Board Class A Power AMP Hifi Vintage Audio Assembled Board
$182.24Amplifier BoardAdd to cartNew update:The appearance is updated from March 6, 2021.SpecificationsAssembled, solder freeDriver tubes:6J1x2PCSPower tubes:FU32x2PCSPower output:3W+3W @8ohmFrequency response:30-40KHz(+-1dB)Input sensitivity:550mVSignal-to noise-ratio:-80dB/3WInput power:85-264VACPower consumption:40WInput impedance:10K ohmOutput impedance:16ohm,8ohm,6ohm,4ohmPackage dimension:12*21*17cmPackage weigth:1.5KGNoteThe self-made shell must be opened with sufficient heat dissipation holes, preferably 50% of the shell area, at least 30%, otherwise it will affect the service life.Package Included1 x End 6J1 …
Caturda C2707 4Channel I2C interface Current Voltage Power Monitoring Module for Raspberry Pi
$39.03Raspberry Pi & Orange PiAdd to cartSpecificationsCurrent and power monitor for Raspberry Pi, 4 channels, can monitor the current, voltage, power and voltage across the sampling resistor through the I2C/SMBus interfaceFeaturesRaspberry Pi 40pin GPIO Interface, fit for Raspberry Pi all SeriesSupport 4 Channel I2C/SMBus CommunicationOnboard 1ohm 1% Resistance.Monitor 3.2A Bidirectional current12bit ADC Measuring 0-26V VoltageWorking Voltage:3.3V/5VInterface:I2C/SMBusResistance:1ohm 1%Voltage Range:0-26VCurrent:÷3.2ASize:65mmx30mmPackage Included1* Monitoring Module
Reviews
There are no reviews yet.