DC 12V-36V 15A 500W Brushless Motor Controller BLDC Driver Board Stall Over-current Protection
$30.60
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Operating voltage:DC 12V-36V
Operating Current
Driver Power
Speed Voltage:0.1V-5V
Operating Temperature:-40~85°C
Humidity:90%RH
Stall protection:Yes
Enable Control:Yes
Over-current protection:Yes
Steering control:Yes
Speed control signal:Yes
Size:63 x 42 x 17mm (L x W x H); Probe size 3mm, length:fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
MA(motor phase U)
Set for the control side
GND:control terminal ground
VR:the governor end 0-5V(corresponding to 10% of motor speed -100%)
ZF:reversing control(connected to 5V or ground can charge the motor rotation direction)
M:tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL:enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V:5V control terminal
Wiring
Control terminal for SET
1. The motor speed control wiring methods:available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.
2. Motor steering control wiring methods:you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.
3. Pulse speed signal:high and low output . IC can not understand the information with the customer request.
Note
Motor driver board 12-36V DC power input, VCC positive power supply,GND power supply is negative.
Electrical wiring methods:Brushless DC motor for the three lines, corresponding MA/U, MB/V, MC/W
Tips
If you use less than 60W, without additional heat sink , be sure to add more than 60W
heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
Package Includes
1 x 12-36V 500W Brushless Motor Controler
Weight | 0.027 kg |
---|
Customers Also Viewed
LM338K 3A Voltage Digital Display High Power Adjustable Linear Module Buck Step Down Regulator
$29.73Power Supply ModuleAdd to cartParameterBoard size:9.6cm x 5.8cmDC input:3-35 voltsAC input:1-25 voltsOutput DC:1.2-30 volts; kit weight:155 gramsMaximum current:3 amps, (LM338K theory can go to 5A, we use domestic LM338K, up to 3A, import disassemble up to 5A)Input and output minimum differential:3 voltsMaximum power consumption:50WAbout LM338K maximum power calculationFor example, input 25V, output 18v load current 2A, then the power …
5Pcs Yushun LS-5S 24V 5W AC to DC Switching Power Supply Module Monitoring Power Supply with White Shell
$32.16Power Supply ModuleAdd to cartFeatures1. Wide input voltage range2. With overload, short circuit and over temperature protection functions3. Small size, high efficiency4. Full load aging test5. Ultra-low output rippleSpecificationBrand:EshionModel:LS-5SVoltage:24V200mA LS-5S24Modulation method:pulse width modulation (PWM) typeTransistor connection mode:single-endedInput voltage:86-264VInput voltage range:100~264V ACOutput /Rated power:5WOutput voltage:24VWork efficiency:75%~76%Output ripple noiseVoltage adjustment rate:÷1%Load regulation rate:÷1%Product Certification:CEOutput current:0.2AFrequency range:47~63HZWorking temperature:-20→~+50→Dimensions:58mm*30mm*22mmWeight:25g(1pcs)Package included5 x Power Supply …
SIM7020C NB-IoT Expansion Board Full Netcom Module Support for Arduino LWM2M/COAP/MQTT/TCP/UDP/HTTP/HTTPS
$52.47Expansion Board & ShieldAdd to cartFeatureOnboard Raspberry Pi interface, can be directly inserted into any version of Raspberry PiSupport LWM2M/COAP/MQTT/TCP/UDP/HTTP/HTTPS and other protocol communicationsSupport domestic OneNET/telecom cloud/aira cloud platformOnboard USB interface, can be used for power supply or software debuggingLead out UART control interface, can be used to connect Arduino/STM32 and other main control boardsOnboard level conversion circuit, the default …
10pcs 3.3V 5V 8 Bit Blue Common Anode LED indicator Display Module DIY Kit
$21.59Display ScreenAdd to cartDescriptionIt can be inserted directly into Breadboard,Ideal for linking up to your Arduiuo UNO Mini Nano Mega2560 DUE Breadboard etc,or others MCU ( AVR STM32 ARM7 ARM9 ARM10 ARM11 PIC C8051 STC MSP430 FPGA/CPLD etc.) SpecificationsColor:BlueWorking Voltage:DC 3-24VPolarity:Common anodeInterface:2.54MM with PIN/2.54MM no PINSize:22.86 x 14.13 x 2.11 mmWeight:1.3gApplicationMCU/ARM/FPGA/Atmega328pPLC MotorElectronic diy kitESP8266/nodemcuNANO/UNO/MEGA2560/BreadboardRaspberry pi 4/robotPackage Incldued10 x …
10pcs 3.3V 5V 8 Bit Blue Common Anode LED indicator Display Module DIY KitRead More
infrared Light Board 42*IR LED Board for CCTV Camera Night Vision 850nm DC12V
$6.55LED BoardAdd to cartDescription– Infrared IR LED boards for CCTV cameras night vision.– Power supply exceeds DC13V may greatly reduce the LEDs operating life.SpecificationsBoard Diameter:60 mminner Diameter:32mmPower Supply:DC12V / 220mA Operation Temperature:-10→ to +50→LED Lamps / Bulbs Size:5mmIR Lights WaveLength:850nmPackage Included1 x 42*IR LED Board for CCTV Camera
10pcs XY-SP5W 5128 Mini Class D Digital Amplifier Board 5W Mono Audio Power Amplifier
$15.27Amplifier BoardAdd to cartFeatures∵ Operating current:>1A∵ Power Output:3~5W∵ Drive Speaker:4~8∵ SNR:85dB@ VDD=5V,Vorms=1V∵ Class D Audio Amplifier∵ Low Distortion, Low Noise FloorNotes1.2.5V to 5.5V operation from a single supply ,and damaged upper 5.5V.2.A 5V/1A DC adapter is recommended to supply the module.3.The circuit will be damaged if the power polarity is oppsite.4.4 3W Speaker is recommended5.With mute fuction, Mute …
10pcs XY-SP5W 5128 Mini Class D Digital Amplifier Board 5W Mono Audio Power AmplifierRead More
10Pcs 2 Key Press Film Switch Module Single Chip Microcomputer Extended Keyboard Electronic Switch Module
$16.11Other Module BoardAdd to cartSpecificationsProduct thickness:1.00mm (+0.02mm)Panel material:PCBack adhesive tape:white glueButton strength:280gTemperature:-15 ° C / +65 ° CCircuit material:0.125mm PET transparentButton package type:button planeButton package height:0.3mmKey life:>100,000 timesLoop resistanceConnector:2.54mm square hole with protective coverSize:40*20mmPackage Included10 x 2 Key Press Film Switch
Reviews
There are no reviews yet.