DC 12V-36V 15A 500W Brushless Motor Controller BLDC Driver Board Stall Over-current Protection
$30.60
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Operating voltage:DC 12V-36V
Operating Current
Driver Power
Speed Voltage:0.1V-5V
Operating Temperature:-40~85°C
Humidity:90%RH
Stall protection:Yes
Enable Control:Yes
Over-current protection:Yes
Steering control:Yes
Speed control signal:Yes
Size:63 x 42 x 17mm (L x W x H); Probe size 3mm, length:fixing hole center distance 57mm; width:fixed hole center distance 36.5mm
Power terminal Out
VCC(positive power supply)
GND(negative one)
MC(motor phases W)
MB(motor phases V)
MA(motor phase U)
Set for the control side
GND:control terminal ground
VR:the governor end 0-5V(corresponding to 10% of motor speed -100%)
ZF:reversing control(connected to 5V or ground can charge the motor rotation direction)
M:tachometer pulse output(depending on the number of motor poles corresponding to the number of pulse per revolution of the output number)
EL:enable control terminal(connected to 5V ot ground running then 5V, grounding the motor stops)
5V:5V control terminal
Wiring
Control terminal for SET
1. The motor speed control wiring methods:available potentiometer system speed can also be connected to the MCU control, when the potentiometer control wiring, the potentiometer middle pin is connected to VR speed port, potentiometer connected to both ends of 5V and GND terminal voltage more high speed faster.
2. Motor steering control wiring methods:you can switch control can also be connected to the MCU control, to GND in one direction, then in one direction 5V.
3. Pulse speed signal:high and low output . IC can not understand the information with the customer request.
Note
Motor driver board 12-36V DC power input, VCC positive power supply,GND power supply is negative.
Electrical wiring methods:Brushless DC motor for the three lines, corresponding MA/U, MB/V, MC/W
Tips
If you use less than 60W, without additional heat sink , be sure to add more than 60W
heatsink fins drive efficiency without lowering the temperature is too high will shine into permanent damage! The size of the heat sink may be a bad environment based work(recommended cooling surface area greater than 200 square centimeters)!When installing the heat sink ,must pay attention to the back of the module 6 MOS pipe insulation, no insulation, it will be adhered to drive plate permanently damaged! Proposes to add insulation films, both sides of the insulating sheet plus thermal grease!
Package Includes
1 x 12-36V 500W Brushless Motor Controler
Weight | 0.027 kg |
---|
Customers Also Viewed
10pcs ZF-1 ASK 315MHz Fixed Code Learning Code Transmission Module Wireless Remote Control Receiving Board
$33.80Smart ModuleAdd to cartFeatureProduct model:ZF-7 (with code)Transmission frequency:315MHZWorking voltage:DC 9V ~12VModulation method:ASKQuiescent current:0uAWorking current:30~45mACoding type:fixed code (SC2262)Radiated power:30~45mWTransmission distance:1000 meters (receiver sensitivity -108dBm)Volume:40mm*20mm*10mm:PIN:Description1:ANT:RF signal input pin, this pin should be connected to the antenna2:-:Negative power supply3:+:Positive power supply4:H-L:Digital pinRated parameter:Symbol:ValueDC supply voltage:VDD-VSS:9V-12VStorage temperature range (TS):TSTG:-12°C to 75°CWelding temperature:+260°CPackage includes10 x Receiver Board
2pcs Digital DC 0-100V 0-10A 250W Tester DC7-12V LCD Digital Display Voltage Current Power Meter Voltmeter Ammeter Amp Detector Geekcreit for Arduino – products that work with official for Arduino boards
$34.98Test & Measuring ModuleAdd to cartSpecificationsSimultaneous display of voltage and currentVoltage Measurement Range:DC 0-100VCurrent Measurement Range:0-10APower Measurement Range:0-1000WVoltage Error Range:÷1% (Adjustable)Current Error Range:÷1% (Adjustable)Power Error Range:÷1% (Adjustable)Refresh Rate:300ms/TimesDisplay Method:HTN LCD 3 Rows of 3 DigitsSupply Voltage:DC 7-12VWorking CurrentWorking Temperature:-10 to 60→Package Included2 x DC Digital Voltmeter Ammeter 4 x Cable
5pcs ESP8285 Development Board Nodemcu-M Based on ESP-M3 WiFi Wireless Module Compatible with Nodemcu Lua V3
$49.76Motherboard & Development BoardAdd to cartOverview1. It is fully compatible with Nodemcu V3, but cheaper than it is. NodeMcu is an open source firmware and development tool that helps you prototype your IOT products in several Lua script lines.2. The ESP8285-based development kit integrates GPIO, PWM, IIC, 1-Wire and ADC into a single board.3. The fastest way with the NodeMCU …
Vacuum Cleaner Charger Base for iRobot Roomba 5 6 7 8 9 Serie 595 780 880 860 980 960 Charger Base Dock
$85.04Solar CollectorsAdd to cartSpecificationName:Charger Base DockModel:C04612Material:Plastic Color:Black Size:As picture shownApplication Models:For iRobot Roomba 500/600/700/800/900Features-Let the robot automatically recharge when there is no power.-A good helper for family cleaning.Package Include1 x Charger Base Dock1 x Charger Cable
DC 12V 3.5mA Microphone Pickup Audio Microphone Amplifier Module DIY Kit Dual Track Output Gain Adjustable
$4.93DIY Electronic KitsAdd to cartDescriptionProduct name:Microphone with adjustable sensitivityWorking voltage:DC9-15V, 12V recommendedWorking current:above 100mAResponse frequency:20Hz-20KHzMonitoring range:about 100 square metersFinished product size:length 56 * width 25 * height 16mmProduct net weight:15 gramsThe power input has anti-reverse protection, which can effectively prevent the module from being damaged if the power is reversed.Product descriptionThis product uses a low-noise processing chip, plus a …
3pcs 5V LED Traffic Light Display Module Electronic Building Blocks Board
$4.85Display ScreenAdd to cartFeatureSize:56 x 21 x 11mmFixing hole:3mmPitch:15mmColor:red yellow greenLED:8mm x 3Brightness:Normal brightnessVoltage:5VInput:Digital levelInterface:common cathode, red, yellow and green separate controlPlatform:, microcontrollerPackage includes3 x LED Traffic Light Module
Upgraded Version 3D Light Cube Kit 8x8x8 Blue LED MP3 Music Spectrum DIY Electronic Kit
$72.16DIY Electronic KitsAdd to cartNote1. This product does not include housing!! if you need the housing, please purchased separately (Product ID:1247731).2. This is a DIY kit, you need to have some knowledge of electronics and ability.3. Need a lot of soldering, you should have enough patience.4. 8x8x8 blue lights display version.5. APP function only supports Android6. File:Click here to …
Upgraded Version 3D Light Cube Kit 8x8x8 Blue LED MP3 Music Spectrum DIY Electronic KitRead More
Reviews
There are no reviews yet.