3pcs 4.5V – 24V To 0.8V-12V DC-DC Buck Step Down Converter Adjustable Power Module
Shipping:Standard Shipping about 10-25 business days
Input Voltage:4.5V – 24V
Output Adjust Voltage:0.8V-12V
Output Fixed Voltage:3.3V 5V 9V 12V ( just need to shorting pads)
Output Current:3A (Max)
Long Time Working Current:2.1A
Conversion Efficiency:97.5% (Maximum 6.5V to 5V 0.7A)
Output Ripple:20mV (12V to 5V 3A)
Welding Hole Spacing:2.54mm
Load Regulation:± 1%
Voltage Regulation rate:± 0.5%
Dynamic Response Speed:5% 200uS
Output Short Circuit Protection:YES
Input Reverse Protection:No
Enable control:high level work, the low level not work, the high level of 2-5V, the low level of about 0V. Default internal pull up to the input positive
DIY mobile power, monitor power supply, embed regulator, camera power supply, car power, communications equipment supply, Vehicle mounted power supply, Security monitoring, Industrial control board, Household electrical appliances etc.
– The maximum output current 3A, a long time running 2.1A, the margin is sufficient. 3A run for about 20 seconds into the chip to protect against overheating, can be cooled by the chip cooling work in 3A current.
– the use of new design, circuit design does not require electrolytic capacitors and tantalum capacitors (electrolytic capacitor life is short, tantalum capacitor explosion risk). Using the current high-end circuit on the use of large-size solid-state ceramic capacitors (MCC) 3pcs.
– The use of non-isolated DC synchronous rectification, circuit conversion efficiency is very high, in 6.5V to 5V 0.7A when the efficiency of up to 97.5%, 12V to 5V 1A time also reached 94%.
– The use of one-piece forming inductors, ultra-low resistance, to maximize the conversion efficiency. Reduce heat, improve efficiency, lower than ordinary shielding inductance heat.
– Ultra-low quiescent current, 12V input and output 5V voltage, with LED lights under the case of light – the static current is less than 0.45 mA. Connected to the car battery without the need for switching, can be connected to the lighter line, or ACC line.
– Output integrated adjustable and fixed voltage, fixed output is not necessary to customize, directly on the board can be spot welding, the special voltage can be used potentiometer adjustment, versatility is very strong.
– Output with LED light instructions to facilitate the visual indication of a voltage output.
– With the enabled port, the default is the operating mode, low level off, for the control to bring convenience
– Can be used to replace the 78 series linear regulator.
– Input and output are used 2.54mm pitch pinhole, and 7805 pin spacing, easy to use processing.
3 x Step Down Buck Module
Customers Also Viewed
5pcs USB Digispark Kickstarter ATTINY85 for Micro USB Development Board OPEN-SMART for Arduino – products that work with official for Arduino boards$28.66Motherboard & Development BoardAdd to cart
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.DescriptionAbout the USB Digispark is an Attiny85 based microcontroller development board similar to the for Arduino line, only cheaper, smaller, and a bit less powerful.With a whole host of shields to extend …
5pcs 12V Volume infrared induction Switch Module LED Lamp Sensor Switch Module$46.85Sensor & Detector ModuleAdd to cart
DescriptionAutomatic control products based on infrared technology, when someone enters the switch induction range, the sensor detects the change of infrared spectrum of human body. The switch automatically turns on the load, and the switch keeps moving without leaving the induction range. After the person leaves, the switch automatically closes the load with a delay. …
GDCPH 2.7V60F Super Farad Capacitor Module 13.5V12F Backup Power Rectifier$23.76Electronic Accessories & SuppliesAdd to cart
FeaturesFast charge and discharge.Long life. Large capacity. High power density. Good low temperature characteristics.SpecificationBrand:GDCPHModel:13.5V12FSeries:Super capacitor (13.5V)Nominal capacity:12FTolerance:10 (%)Rated voltage:12-13.5V (V)Working temperature range:-20~65→Termination type:weldingLead spacing:101mmSize:101mm*42mm*20mm(Length * height * width)Height-installation (maximum):42mmShell:aluminum shellPackage included1 x Super capacitor
5pcs ACS712 Module 30A Current Detection Board ACS712 Hall Current Sensor Module$20.52Sensor & Detector ModuleAdd to cart
>>>Manual:Click here to openFeaturesThe current sensor chips:ACS712ELC-30APin 5V power supply, on-board power indicator;No test current through the output voltage is VCC / 2;PCB board size:31 (mm) x13 (mm);NoteACS712 is based on the principle of the Hall test, please use this field to avoid impactPackage Included5 x 30A Current Sensor Module ACS712T
10 pcs DC 5V 5mW 650nm 6mm Laser Dot Diode Module Red Copper Head Tube$8.73Module ComponentsAdd to cart
FeaturesWorking life:more than 2000 hoursSpot mode:dot facula, continuous outputLaser wavelength:650nm (red)Copper head diameter:6mmLight powerSupply voltage:5V DCOperating currentOperating temperature:-36→ ~ 65→Power lead length:120mmShell material:brassSingle weight:1gPackage included10 x Laser diode dot
M5Stack PRO 13.2 Universal DIY Pro Stack Module 2.54 mm Hole Pitch ProShield for ESP32 Protype Expansion Board$13.11Expansion Board & ShieldAdd to cart
DescriptionPRO 13.2 is a universal DIY pro module in the m5stack stack module series, with a height of 13.2mm. You can easily build your own custom circuits by using this module. You can design and build the protype circuit according to your own needs, and interact with the M5 Core on the top layer through …