10pcs 4.5V – 24V To 0.8V-12V DC-DC Buck Step Down Converter Adjustable Power Module
$19.95
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
Material:Circuit Board
Color:Red
Size:17mmx10mm
Input Voltage:4.5V – 24V
Output Adjust Voltage:0.8V-12V
Output Fixed Voltage:3.3V 5V 9V 12V ( just need to shorting pads)
Output Current:3A (Max)
Long Time Working Current:2.1A
Conversion Efficiency:97.5% (Maximum 6.5V to 5V 0.7A)
Switch Frequency:500kHZ
Output Ripple:20mV (12V to 5V 3A)
Welding Hole Spacing:2.54mm
Load Regulation:± 1%
Voltage Regulation rate:± 0.5%
Dynamic Response Speed:5% 200uS
Output Short Circuit Protection:YES
Input Reverse Protection:No
Enable control:high level work, the low level not work, the high level of 2-5V, the low level of about 0V. Default internal pull up to the input positive
Application areas
DIY mobile power, monitor power supply, embed regulator, camera power supply, car power, communications equipment supply, Vehicle mounted power supply, Security monitoring, Industrial control board, Household electrical appliances etc.
Features
– The maximum output current 3A, a long time running 2.1A, the margin is sufficient. 3A run for about 20 seconds into the chip to protect against overheating, can be cooled by the chip cooling work in 3A current.
– the use of new design, circuit design does not require electrolytic capacitors and tantalum capacitors (electrolytic capacitor life is short, tantalum capacitor explosion risk). Using the current high-end circuit on the use of large-size solid-state ceramic capacitors (MCC) 3pcs.
– The use of non-isolated DC synchronous rectification, circuit conversion efficiency is very high, in 6.5V to 5V 0.7A when the efficiency of up to 97.5%, 12V to 5V 1A time also reached 94%.
– The use of one-piece forming inductors, ultra-low resistance, to maximize the conversion efficiency. Reduce heat, improve efficiency, lower than ordinary shielding inductance heat.
– Ultra-low quiescent current, 12V input and output 5V voltage, with LED lights under the case of light – the static current is less than 0.45 mA. Connected to the car battery without the need for switching, can be connected to the lighter line, or ACC line.
– Output integrated adjustable and fixed voltage, fixed output is not necessary to customize, directly on the board can be spot welding, the special voltage can be used potentiometer adjustment, versatility is very strong.
– Output with LED light instructions to facilitate the visual indication of a voltage output.
– With the enabled port, the default is the operating mode, low level off, for the control to bring convenience
– Can be used to replace the 78 series linear regulator.
– Input and output are used 2.54mm pitch pinhole, and 7805 pin spacing, easy to use processing.
Package Includes
10 x Step Down Buck Module
Weight | 0.02 kg |
---|
Customers Also Viewed
Multiple Car Toys Magnetic Puzzle Box Book Educational Book Kids Learning Gift
$52.64MathematicsAdd to cartPackage included10 x Card76 x MagnetsFeatures1.Developing kids’ intelligence.2.Teaching kids to know more words.3.Easy for storage.SpecificationsColor:MulticolorMaterial:Paperboard, MagnetismSize:30x4x21.5cm
Basic Starter Kit UNO R3 Mini Breadboard LED Jumper Wire Button with Box for Geekcreit for Arduino – products that work with official Arduino boards
$18.62Module KitsAdd to cartDescriptionsPerfect for Shield Prototyping and TestingPlastic housing, metal contact clipsAccept wire with diameter 20-29AWGVolatge/current:300V/3-5A400 tie-point2 Power Lanes, Tie-point 1001 Double-strip, Tie-point 300Solderless Breadboard Size:82x55x8.5mmPackage included1 x Uno R3 Development Board1x 400 hole Breadboard10 x 220Ω resistor 5% carbon film10 x 1k resistor 5% carbon film10 x 10k resistor 5% carbon film10 x 100k resistor 5% …
3pcs ESP32-S WiFi + Bluetooth ESP32S Serial to WiFi Dual Antenna Module
$29.27Smart ModuleAdd to cartDescriptionThe main chip uses a low-power dual-core 32-bit CPU with a frequency of up to 240MHz and computing power of up to 600DMIPS.Default 32Mbit SPI Flash, 520KB SRAMSupport SoftAP and Station modeUltra-small 802.11b/g/n Wi-Fi + BT/BLE SoC moduleSupport UART/SPI/I2C/I2S/PWM/ADC/DAC, etc.Support for firmware upgrade (FOTA)Antenna supports onboard antenna or IPEX block outputPackage includes3 x Wifi module
Geekcreit 433MHz DC 12V 10A Relay 1CH Channel Wireless RF Remote Control Switch Transmitter with Receiver
$15.30Smart ModuleAdd to cartIf you need more Transmitter, please buy Product ID:1215079>>>Manual:Click here to openFeaturesEasy to install and easy to carryWith a slidable cover on the remote controlWith a hook on the remote controlUse Learning coding, stable and reliableThe wireless signal can pass through walls, floors and doorsYou can turn on or turn off the receiver with transmitter …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStream
$56.69Electrical Pump & ValveAdd to cartFeature*CO2 Refill Adapter is used to fill CO2 into your Sodastream tank.*Adjustable valve pin ensures compatibility with any cylinder valve variation.*Easy to install and use.*Made of high quality metal, high hardness and durable.Specification*Material:Metal*Color:Silver (As Pictures Show)*Inner Thread:TR21-4*Outer Thread:W21.8-14Package Contents1*CO2 Refill AdapterNotes:The real color of the item may be slightly different from the pictures shown on …
CO2 Refill Adapter Connector Kit W21.8-14 Thread Set for Filling SodaStreamRead More
30pcs 2.5-5.5V TTP223 Capacitive Touch Switch Button Self Lock Module
$15.15Other Module BoardAdd to cartFeatures 1. Size:15*11mm 2. Power:2.5-5.5V 3.Trigger setting mode:(1->Short;0->No Short) AB=00:No-lock High TTL level output; AB=01:Self-lock High TTL level output; AB=10:No-lock Low TTL level output; AB=11:Self-lock Low TTL level output; Package included 30 x 2.5-5.5V TTP223 Capacitive Touch Switch Button Self-Lock Module For
NE555 Pulse Module LM358 Duty and Frequency Adjustable Square Wave Signal Generator Upgrade Version
$6.55Test & Measuring ModuleAdd to cartFeature1. Used as a square wave signal generator to generate square wave signals for experimental development.2. Used to generate a square wave signal that drives the stepper motor driver.3. Generate adjustable pulses for use by the MCU.4. Generate adjustable pulses to control the associated circuitry.Description1. Size:3.5CM * 4.6CM1. The main chip:LM358;2. Input voltage:5V-12VDC.3. Input current:≥100MA;4. …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module Kit
$13.73DIY Electronic KitsAdd to cartFeatureModel:AUL-10Supply voltage:DC9V-12VAudio input:0~1.5VrmsPCB size:66 x 28mm (L x W)Light row size:62.5 x 5 x 10.7mm (L x W x H)Two indication modes:bar indication and fire spot indication (Realized by MOD short-circuit point)Lamp row offers two kinds of vertical and horizontal installationTin-treated solder padsNote:Before power on, please confirm the polarity of the power supply is correct …
3pcs LM3915 Level indicator Kit DC9V-12V DIY Electronic Production Module KitRead More
Reviews
There are no reviews yet.