20pcs DC12V 10A 1CH 433MHz Wireless Relay RF Remote Control Switch Receiver Module
$73.26
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
1.Input Voltage:DC10-14V
2.Standby Current
3.RF Frequency:433MHZ
4.RF Working mode:Super heterodyne receiver
5.Receiver Sensitivity:>90dBm
6.Remote Control Distance:>100 meter(In open environment)
7.Decoding Way:MCU Software decoding
8.Can store the number of remote control:50
9.Support remote control type:Fixed code, learning code
10.Channel:1CH
11.Multiple working modes:(Jog/Non-Latched ,inter-lock/Latched ,self-lock /Self-Latched,Delay off)
12.Wiring Method:Fixed wiring terminal
13.Working Voltage:DC12V
14.Output Current:10A
15.Rated load:10A 250VAC / 10A 125VAC
10A 30VDC / 10A 28VDC
16.Output:Normally open,Common,Normally closed
17.Dimension:3.5cm*3cm*1.6cm
Working/output way
1.Jog:Press the learning button then release, set the mode from the system automatically working mode to action mode, wait for a while, when the board LED off, said it is into the learning state, press the remote control, the system received the signal. The LED flashes 5 times and goes off again. After 3S delay, LED light marked learning success, the system automatically withdraw from the learning state.
2.Self-locking:Press the learning button, then release, press 2 times, the system automatically set to self-locking mode, wait for a while, LED off, it is into the learning state, press the remote control, LED flash 5 times Off. 3S after the delay, LED light learning success.
3.Interlock:press the learning button, then release, press 3 times in succession, the system is set to interlock mode.
4.Delay:Press remote control relay pull-in,release the remote control and begin timekeeping,after 5s,10s,15s will automatically close the relay
Description
1. press the learning code .the indicator flash ,loosen your finger ,press any button of the remote control
the indicator flash 2 times and off .it mean you learn it successfully .
2. it can learn more than 12 PCS 2262 or 1527 chip with the different code wireless 433MHz remote control
3. remove/clean:press the learning button about 8 seconds , the indicator turn on to off, it means the information that you keep have been removed successfully .
Package included
20 x 12V 1CH 433MHz Wireless Relay Switch Receiver
Weight | 0.34 kg |
---|
Customers Also Viewed
OPEN-SMART DC Jack Power 7~12V to DC5V/3.3V Step Down Converter Voltage Regulator Power Supply Module for Breadboad
$6.55Power Supply ModuleAdd to cartDescriptionThis is a mini LDO step-down power module based on AMS1117-5.0 and AMS1117-3.3, and it output fixed 5V / 3.3V.It is a small size, lightweight, especially for model airplanes, smart cars, DIY and other items, PCB experiment board project design, breadboard project design.Features– Module type:LDO step-down module;– Onboard 500mA resettable fuse to protect the power …
Temperature Alarm Kit thermistor Electronic Teaching Experiment Training Welding DIY Parts
$5.45DIY Electronic KitsAdd to cartFeatureSize:5.8*3.7cm Power supply voltage:DC 5VFunction introductionRP1, R1, R2, R3 and RT in the circuit form a temperature measuring bridge. When the temperature is below the preset temperature, the potential of pin 2 of UA741 is higher than that of pin 3, pin 6 of 741 outputs a low level, LED1 is on, and the buzzer …
Temperature Alarm Kit thermistor Electronic Teaching Experiment Training Welding DIY PartsRead More
5pcs ESP8266 ESP-01 ESP-01S DHT11 Sensor Temperature and Humidity WiFi Node Module
$18.41Smart ModuleAdd to cartFeatureThis module is mainly controlled by ESP8266-01/ESP-01S, and DHT11 is a temperature and humidity sensor. The temperature and humidity in the ESP8266 acquisition environment are uploaded to the server. Support 3.7v-12V DC power supply (3.7V lithium battery). Can be used as a temperature and humidity collection node for smart home or IOT projects.CharacteristicMaster:ESP-01/ESP-01S (This module …
5pcs ESP8266 ESP-01 ESP-01S DHT11 Sensor Temperature and Humidity WiFi Node ModuleRead More
2Pcs/Pack Plastic Tire Wheel with DC 3-6v Gear Motor for Smart Car
$13.93Smart Robot & Solar PanelAdd to cartSpecificationMotor1. Voltage:DC 3V-6V2. Current:100 MA-120MA3. Reduction rate:48:14. RPM (With tire):100-2405. Tire Diameter:65mm6. Car Speed(M/minute):20-487. Motor Weight (g):29/each8. Motor Size:70mm X 22mm X 18mm9. NoiseTire Parameter1. Center hole:5.3MM x 3.66MM2. Wheel size:65 x 26mmPackage Included2 x Smart Car Robot Plastic Tire Wheel2 x DC Gear Motor
ACS714 5A 5V Current Sensor Breakout Board Isolate Filter Resistance Capacitor Hall Effect Module
$16.23Sensor & Detector ModuleAdd to cartIntroductionThis current sensor is a carrier board or breakout board for Allegro’s ACS715LLCTR-30A-T Hall effect-based linear current sensor, The sensor operates at 5 V and has an output sensitivity of 133 mV/A. The board ships fully populated with its SMD components.FeatureDesigned for unidirectional input current from 0 to 5 A, but the sensor will provide …
SPI MCP2515 EF02037 CAN BUS Shield Development Board High Speed Communication Module
$21.86Motherboard & Development BoardAdd to cartIntroduction CAN-BUS is a common industrial bus because of its long travel distance, medium communication speed and high reliability. It is commonly found on modern machine tools and as an automotive diagnostic bus. This CAN-BUS Shield adopts MCP2515 CAN Bus controller with SPI interface and MCP2551 CAN transceiver to give your /Seeeduino CAN-BUS capibility. With …
SPI MCP2515 EF02037 CAN BUS Shield Development Board High Speed Communication ModuleRead More
Reviews
There are no reviews yet.