3pcs MQ-4 Methane Natural Gas Sensor Module Shield Liquefied Electronic Detector Module
$13.03
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Specification
– The gas sensing material used in the MQ-4 gas sensor is tin dioxide (SnO2) with low conductivity in clean air.
– When there is a flammable gas in the environment where the sensor is located, the conductivity of the sensor increases as the concentration of flammable gas in the air increases.
– A simple circuit can be used to convert the change in conductivity into an output signal corresponding to the gas concentration.
– The MQ-4 gas sensor has high sensitivity to butane, propane and methane, and has a good balance between methane and propane.
– This sensor detects a wide range of flammable gases, especially natural gas, and is a low cost sensor for a variety of applications.
– Suitable for monitoring equipment for liquefied gases, natural gas and gas in the home or industry. Excellent resistance to ethanol and smoke.
Features
1. It adopts high quality double panel design with power indication and TTL signal output indication;
2. It has DO switch signal (TTL) output and AO analog signal output;
3. The TTL output valid signal is low. (When the output is low, the signal light is on, it can be directly connected to the MCU or relay module)
4. The voltage of the analog output, the higher the concentration, the higher the voltage.
5. It has good sensitivity to gas and natural gas detection.
6. there are four screw holes for easy positioning;
7. product dimensions:32 (L) * 20 (W) * 22 (H)
8. has a long service life and reliable stability
9. fast response recovery characteristics
Electrical Performance
Dection of gas:Natural gas/Methane
Dection of Concentration:300-10000ppm
Input voltage:DC5V
Power consumption (current):150mA
DO output:TTL digital quantities 0 and 1 (0.1 and 5V)
AO output:0.1-0.3V (relatively non-polluting), the highest concentration voltage is about 4V
Using the chip:AT89S52
Crystal:11.0592MHZ
Baud rate:9600
Compilation environment:Keil
Special Reminder
After the sensor is energized, it needs to be preheated for about 20S, and the measured data is stable. The heating of the sensor is a normal phenomenon, because there is a heating wire inside, if it is hot, it is not normal.
Package Included
3 x MQ-4 Gas Sensor Module
Weight | 0.021 kg |
---|
Customers Also Viewed
5pcs 1206B 3A PWM DC Motor Speed Controller 6V/12V/24V Speed Regulating Switch Electronic Governor Dimmer
$39.45Motor PWM Speed ControllerAdd to cartDescriptionModel:1206BKVoltage:12VPower mode:DC powerVoltage range:DC 6V-28VCurrent range:Within 3ASwitch function:YesSize:57mm*37mmPackage Included5 x Motor Speed Governor
100W 18V High Efficieny Solar Panel USB DC Monocrystalline Solar Charger for Car RV Boat Battery Charger Waterproof
$105.29Solar PanelAdd to cartFeature– Suitable for campers, boats, houses, gardens, shacks or farms– Provide appropriate power for TVs, laptops, lights, refrigerators and other operating equipment.– Flexible board, lightweight and easy to install.– Suitable for RVs, boats, small spaces or crowded areas.SpecificationSolar panelMaterial:Monocrystalline SiliconSize:510x280x3.0mm/20.08×11.02×0.12inPower:100WOpen Circuit Voltage:18VShort circuit current:2AOutput Voltage:DC 18V&9V, USB 5V, Type-C 5VWaterproof grade:IP65Conversion:23-24%Applicable to:Bicycle, mountaineering, hiking, camping, …
CJMCU-219 INA219 I2C Bi-directional Current Power Monitor Sensor Module
$13.11Sensor & Detector ModuleAdd to cartDescriptionCJMCU-219 module is a with I2C interface Bidirectional current / power monitor integrated circuit (IC), and further expand the energy-saving electronic products TI camp. INA219 with the industry’s highest accuracy and smallest size, not only to monitor the voltage drop across a shunt resistor on the sensing shunt supply voltage, while also computing power. The …
CJMCU-219 INA219 I2C Bi-directional Current Power Monitor Sensor ModuleRead More
Reviews
There are no reviews yet.