Robotdyn with POE Leonardo ETH ATmega32U4 Ethernet W5500 (V2) Development Board
$91.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Product Overview
If you’re looking to build a network-connected device, RobotDyn Leonardo ETH(V2) is the best solution for you!
Leonardo ETH(V2) is a fully-featured Ethernet-connected device. Depending on your use case, it can act as a server or a net member. In a server role, it will receive requests from other devices and services in local network and internet, and respond or react accordingly. In a net member role, the RobotDyn Leonardo ETH(V2) can collect data from different devices or industrial equipment and send it through the local network or Internet. It can also receive data from local network and internet, and control connected devices and equipment. The RobotDyn Leonardo ETH(V2) can also act as stand-alone unit, providing autonomous reaction based on the defined algorithm in response to network changes or other triggers.
Leonardo ETH(V2) features two devices on one board:Leonardo based on an ATmega32U4 and Ethernet controller based on WizNet W5500 TCP/IP. It also has an optional PoE function (receiving power directly through the Ethernet cable).
W5500 Ethernet
WizNet W5500 is a TCP/IP embedded Ethernet controller. It provides TCP/IP Stack, 10BaseT/100BaseTX Ethernet with full or half-duplex, MACand PHY. W5500 is using a highly efficient SPI protocol, with 80 MHz clocks for high-speed connectivity to Atmega32U4. For lower energy consumption, W5500 provides WOL (Wake on LAN) and Power Off modes.
Ports and buses
Leonardo ETH (V2) has 23 digital input/output ports, seven of which can be used for PWM, and 12 analog ports with 10-bits resolution (0 – 1023). 5 ports have a hardware interrupt feature. The board is equipped with an RJ45, micro USB, DC power jack, and a reset button. Unlike the other Leonardo ETH clones, Leonardo ETH(V2) has three additional digital SPI bus ports D14, D15, D16, which can be also used to communicate with other devices via SPI.
SD-card
The board also features a microSD card socket. A microSD card can be used to save and store the data, which can later be transferred over the network. Digital port D4 (CS-CS2) of the ATmega32u4 is dedicated to work with the microSD. Digital port D10 (SS-CS2) is used by WizNet W5500. The Ethernet controller and microSD card are connected through the SPI bus, which is brought out as a separate ICSP connector with ports D14, D15 and D16.
HID functions
Leonardo ETH(V2) can also act as an HID device. It can be used as a mouse or keyboard on the connected computer, in addition to the CDC sequenced/COM-port. You can program it to control an application on your PC. For example, you can set it up to turn your PC on, and then launch and control certain applications. The board itself can start an ARDUN0 IDE, open a sketchand start the compilation/upload.
Programming in ARDUN0 IDE
Leonardo ETH(V2) can be programmed via an ARDUN0 IDE. Select ARDUN0 Leonardo or Leonardo ETH in the Boards menu, and use the Ethernet2 / Ethernet3 library.
Power supply
Leonardo ETH(V2) can be powered via
USB port (5V, 500mA);
DC-IN Jack, PWC 2.1mm, (supporting 7-24V DC input voltage);
Through an Ethernet cable using PoE (Power over Ethernet) – requires a PoE-enabled switch or a PoE injector.
Note
With PoE version:this item, without PoE version:Product ID 1660664
The PoE module is optional. There are several PoE options available, depending on the PoE equipment you use.
The Active PoE is compliant with 802.3af or 802.3at. It will check the power coming in, if it doesnt meet the device requirements, it just wont power up.
The Passive PoE is a simplified version that does not perform a handshake, so it is important to know what PoE voltage your device supplies requires before plugging in the Ethernet cable and powering it up. If you connect the wrong voltage you may cause permanent electrical damage to the device.
Make sure to select the correct board option with a relevant PoE module.
Specifications
Leonardo ETH V2
Input Voltage (VIN/DC jack):7~24V
Power IN (USB):5V-limit 500mA
Power IN (PoE):Optional module, 48V(Input), 9V(Output)
Digital I/O:23
PWM Output:7
Analog I/O:12
Reserved Pins:D4 is used for SD card select;
D9 is used for SD card detect;
D10 is used for W5500
D14, D15, D16 are used for SPI.
*Optional:D8 is used for W5500 interrupting, D11 is used for W5500 initialization
USB socket:Micro-USB
Ethernet socket:RJ45
PCB Size:53.3≠68.6mm
Card Reader:Micro SD card, with logiclevel convertor
Weight:41g
Leonardo MCU
Microcontroller:ATmega32u4(AVR)
Operating Voltage:5V
Flash memory:32KB of which 4KB used by bootloader
SRAM:2KB
Clock Speed:16MHz
EEPROM:1KB
Ethernet MCU
Microcontroller:Wiznet W5500
PHY compliance:10BaseT/100BaseTX Ethernet. Full and half-duplex
Operating Voltage:3.3V, 5V I/O signal tolerance
Memory:Internal 32Kbytes Memory for Tx/Rx Buffers
TCP/IP Protocols:TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHY Clock Speed:25MHz
Passive PoE (optional)
Ethernet Power (IN):12~48V DC
Output:DC 9V
PoE type:Passive PoE
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Tutorial:Click here to open
Package includes
1 x Leonardo module
Weight | 0.062 kg |
---|
Customers Also Viewed
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with Cable
$11.26Sensor & Detector ModuleAdd to cartFeatures– Can receive standard 38KHz remote control signals by means of programming can decode the remote control signals– Strong ability to resist electromagnetic interference and light– Widely used in stereo, TV, set-top boxes, digital photo frame, car stereo, remote control toys, satellite receivers, hard disk players, air conditioner, heater, electric fan, lighting and other home …
3pcs 1838T infrared Sensor Receiver Module Board Remote Controller IR Sensor with CableRead More
600V 45A 3 Position Terminal Block Barrier Strip Dual Row Screw Block Covered W/ Removable Clear Plastic insulating Cover
$16.19Terminal BlocksAdd to cartSpecificationModel:TB4503Type:Terminal block Working frequency:High frequencyInterface type:AC/DCRated current:45ARated voltage:600VConductor cross section:0.5-4mm2Number of pin:6Number of bits:3Contact material:IronSize:70mm x 38mm x 24mmFeature:–Moistureproof–High quality guides,durable–High quality thickened conductive parts–High quality iron screw with high strength–Dust proof transparent plastic protective coverPackage Included1 x Terminal block
5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V inverter
$26.31Smart ModuleAdd to cart5Pcs 2 Lamp Backlight Universal LCD CCFL 10V-28V Inverter For 10 Inch To 22 Inch ScreenFeatureVoltage:10V ~ 28VCable:300mm(L) / 6 pinSize:122 x 27mm ( L x W )Interface:double light small interfaceInterface definition:1. VCC 2. GND 3. NULL 4. NULL 5. ON/OFFPackage included5 x 2 lamp backlight universal laptop LCD CCFL inverter 10V-28V5 x Cable
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier Board
$20.90Amplifier BoardAdd to cartFeatures1. Power filter function is through the power line access power filter,get a specific frequency of the power signal, or eliminate a specific frequency power signal. By using this feature of the power filter, a square wave complex or complex noise passing through the power filter can be converted into a sine wave of a …
18A 3900W EMI High Frequency Power Filter Finished Board for amp Amplifier BoardRead More
5pcs EQKIT TDL-555 Touch Delay LED Light DIY Kit Touch Delay Lamp Electronic Parts Production Kit DC 5V 3s to 130s Adjustable
$10.12DIY Electronic KitsAdd to cartFunction1. Connect Power,Red LED ON2. Touch and then start to delay and Red LED OFF and 5pcs White LED ON at the same time3. Red LED ON and White LED OFF after delay4. Delay can be adjust by potentiometer for 3-130 secondPackage included5 x EQKIT® TDL-555 Touch Delay LED Light DIY Kit
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4
$22.95Raspberry Pi & Orange PiAdd to cartOverviewThis is a universal driver board for e-Paper panels, can be used to drive various SPI interface e-Paper from Waveshare.FeaturesStandard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson NanoSPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.Onboard voltage translator, compatible with 3.3V/5V MCUsComes with development resources and manual (examples …
Waveshare Universal e-Paper Panel Driver HAT SPI Surface for Raspberry Pi 4Read More
Reviews
There are no reviews yet.