Robotdyn with POE Leonardo ETH ATmega32U4 Ethernet W5500 (V2) Development Board
$91.04
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Product Overview
If you’re looking to build a network-connected device, RobotDyn Leonardo ETH(V2) is the best solution for you!
Leonardo ETH(V2) is a fully-featured Ethernet-connected device. Depending on your use case, it can act as a server or a net member. In a server role, it will receive requests from other devices and services in local network and internet, and respond or react accordingly. In a net member role, the RobotDyn Leonardo ETH(V2) can collect data from different devices or industrial equipment and send it through the local network or Internet. It can also receive data from local network and internet, and control connected devices and equipment. The RobotDyn Leonardo ETH(V2) can also act as stand-alone unit, providing autonomous reaction based on the defined algorithm in response to network changes or other triggers.
Leonardo ETH(V2) features two devices on one board:Leonardo based on an ATmega32U4 and Ethernet controller based on WizNet W5500 TCP/IP. It also has an optional PoE function (receiving power directly through the Ethernet cable).
W5500 Ethernet
WizNet W5500 is a TCP/IP embedded Ethernet controller. It provides TCP/IP Stack, 10BaseT/100BaseTX Ethernet with full or half-duplex, MACand PHY. W5500 is using a highly efficient SPI protocol, with 80 MHz clocks for high-speed connectivity to Atmega32U4. For lower energy consumption, W5500 provides WOL (Wake on LAN) and Power Off modes.
Ports and buses
Leonardo ETH (V2) has 23 digital input/output ports, seven of which can be used for PWM, and 12 analog ports with 10-bits resolution (0 – 1023). 5 ports have a hardware interrupt feature. The board is equipped with an RJ45, micro USB, DC power jack, and a reset button. Unlike the other Leonardo ETH clones, Leonardo ETH(V2) has three additional digital SPI bus ports D14, D15, D16, which can be also used to communicate with other devices via SPI.
SD-card
The board also features a microSD card socket. A microSD card can be used to save and store the data, which can later be transferred over the network. Digital port D4 (CS-CS2) of the ATmega32u4 is dedicated to work with the microSD. Digital port D10 (SS-CS2) is used by WizNet W5500. The Ethernet controller and microSD card are connected through the SPI bus, which is brought out as a separate ICSP connector with ports D14, D15 and D16.
HID functions
Leonardo ETH(V2) can also act as an HID device. It can be used as a mouse or keyboard on the connected computer, in addition to the CDC sequenced/COM-port. You can program it to control an application on your PC. For example, you can set it up to turn your PC on, and then launch and control certain applications. The board itself can start an ARDUN0 IDE, open a sketchand start the compilation/upload.
Programming in ARDUN0 IDE
Leonardo ETH(V2) can be programmed via an ARDUN0 IDE. Select ARDUN0 Leonardo or Leonardo ETH in the Boards menu, and use the Ethernet2 / Ethernet3 library.
Power supply
Leonardo ETH(V2) can be powered via
USB port (5V, 500mA);
DC-IN Jack, PWC 2.1mm, (supporting 7-24V DC input voltage);
Through an Ethernet cable using PoE (Power over Ethernet) – requires a PoE-enabled switch or a PoE injector.
Note
With PoE version:this item, without PoE version:Product ID 1660664
The PoE module is optional. There are several PoE options available, depending on the PoE equipment you use.
The Active PoE is compliant with 802.3af or 802.3at. It will check the power coming in, if it doesnt meet the device requirements, it just wont power up.
The Passive PoE is a simplified version that does not perform a handshake, so it is important to know what PoE voltage your device supplies requires before plugging in the Ethernet cable and powering it up. If you connect the wrong voltage you may cause permanent electrical damage to the device.
Make sure to select the correct board option with a relevant PoE module.
Specifications
Leonardo ETH V2
Input Voltage (VIN/DC jack):7~24V
Power IN (USB):5V-limit 500mA
Power IN (PoE):Optional module, 48V(Input), 9V(Output)
Digital I/O:23
PWM Output:7
Analog I/O:12
Reserved Pins:D4 is used for SD card select;
D9 is used for SD card detect;
D10 is used for W5500
D14, D15, D16 are used for SPI.
*Optional:D8 is used for W5500 interrupting, D11 is used for W5500 initialization
USB socket:Micro-USB
Ethernet socket:RJ45
PCB Size:53.3≠68.6mm
Card Reader:Micro SD card, with logiclevel convertor
Weight:41g
Leonardo MCU
Microcontroller:ATmega32u4(AVR)
Operating Voltage:5V
Flash memory:32KB of which 4KB used by bootloader
SRAM:2KB
Clock Speed:16MHz
EEPROM:1KB
Ethernet MCU
Microcontroller:Wiznet W5500
PHY compliance:10BaseT/100BaseTX Ethernet. Full and half-duplex
Operating Voltage:3.3V, 5V I/O signal tolerance
Memory:Internal 32Kbytes Memory for Tx/Rx Buffers
TCP/IP Protocols:TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE
PHY Clock Speed:25MHz
Passive PoE (optional)
Ethernet Power (IN):12~48V DC
Output:DC 9V
PoE type:Passive PoE
Documents
Dimensional drawing:Click here to open
Pinout:Click here to open
Schematic:Click here to open
Tutorial:Click here to open
Package includes
1 x Leonardo module
Weight | 0.062 kg |
---|
Customers Also Viewed
3pcs TP5100 Single 4.2V / Dual 8.4V 2A Lithium Battery Charging Board
$11.00Battery Protection ModuleAdd to cartParameterSize:25*17*5mm (length*width*height)Input voltage:DC 5-18V(actual 5-12V is appropriate)Charging status:full and no-load blue light, red during chargingThe voltage setting must be operated in the power-off state, and the switch must be disconnected before switching.Can also be used for white LED constant current drive:set a single lithium drive one, set dual lithium drive two stringsCharacteristic1. Dual / single …
3pcs TP5100 Single 4.2V / Dual 8.4V 2A Lithium Battery Charging BoardRead More
Geekcreit UNO R3 Super Starter Kits Geekcreit for Arduino – products that work with official Arduino boards
$70.34DIY Electronic KitsAdd to cartDescriptionThis super Start kit not only contains UNO R3 control board, but also includes LED diodes, resistors, LCD1602, RFID module, sound module, over than 50 kinds of components and sensors, Which meet your de-mands for different projects either it is simple or complex.Package included5 x White LED5 x Yellow LED5 x Blue LED5 x Green …
1 Layer Stainless Steel Rice Noodle Roll Steamer Rice Roll Maker Steaming Tray
$133.64Laser BoresighterAdd to cartFeature1. 1 Layer with 2 trays.2. Very easy to use.3. Heating quickly.4. 301grade stainless steel.5. Durable laser panel.6. Easy to clean, no rust.7. Edge rounded design, not easy to cut.SpecificationMaterial301grade stainless steelColorSilveryHeating TypeGas steam boiler electric steamerSize33x30x9cm/13’x11.8’x3.5′HOW TO USE1. Mix the flour, water, eggs, minced meat and seasoning into flour paste2. Add water to the …
1 Layer Stainless Steel Rice Noodle Roll Steamer Rice Roll Maker Steaming TrayRead More
10pcs 4 Slots 18650 Battery Holder Plastic Case Storage Box for 4*3.7V 18650 Lithium Battery with 8Pin
$31.83Other Module BoardAdd to cartSpecificationsSupport Model:18650 BatteryShell material:ABS fire, flame retardant, high temperature, color diversity and other materials for choice.Metal spring:carbon steel nickel plating by NCAA salt spray test, stainless steel spring.External:wire, welding pieces, pins, male and female buckle (3.7v button)Terminal:copper nickel platingCorn:nickel plated with coppervPackage Included10 x 4 Slots 18650 Battery Holder Plastic Case Storage Box
CJMCU-633 LSM6DSO 6DOF 3D Gyroscope Attitude Sensor Module 3D Accelerometer 3.3V SPI IIC I2C MIPI I3C SM Serial interface
$22.40Sensor & Detector ModuleAdd to cartFeatureLSM6DSO is an attitude module with 3D digital accelerometer and 3D digital gyroscope. Improve performance at a speed of 0.55 mA in high-performance mode, and enable the always-on low-power function. LSM6DSO supports major OS requirements, provides real, virtual and batch processing of 9 KB sensors for dynamic data batch processing, compatible with AndroidoProduct parameters1. Linear …
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle Adjustable
$34.82Other Module BoardAdd to cartProduct Introduction1. Operating Voltage:5-30V,support micro USB 5.0V power supply2. Frequency Range:1Hz~150KHz3. Frequency Precision:2%4. Signal Load Capacity:output current is within 8–30mA5. Output Range:default 5V V-pp (can be changed by external power)6. Ambient Temperature:-30 Celsius ~70 Celsius Application Fields1. As square wave generator to generate square wave for experiment development2. Used to drive steeping motor driver’s square …
5pcs 2 Channel PWM Generator Module Pulse Frequency Duty Cycle AdjustableRead More
Accuracy 0.01mm Dial Test Coaxial Centering indicator Centre Finder Milling Tool
$263.24Solar CollectorsAdd to cartDescriptionThe utility model is used for determining the relative position of the inner and outer centers of theworkpiece and the center of the machine tool spindle. It has the care of the shaft rotation, theindicator is always faced with the characteristics of the operator.SpecificationsName:Centering dial test indicatorMaterial:metalColor:silver,blueRange:0-3mmGraduation:0.01mmSize:14x4cmBox size:22x12x6.5cm(LxWxH)Features-Centering dial test indicator is mainly to find …
Accuracy 0.01mm Dial Test Coaxial Centering indicator Centre Finder Milling ToolRead More
Reviews
There are no reviews yet.