600×448 5.83inch E-ink Display e-Paper HAT(B) for Raspberry Pi Red/Black/White Color SPI interface
$145.58
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Overview
This is an E-Ink display HAT for Raspberry Pi, 5.83inch, 600×448 resolution, with embedded controller, communicating via SPI interface, supports red, black, and white three-color display.
Due to the advantages like ultra low power consumption, wide viewing angle, clear display without electricity, it is an ideal choice for applications such as shelf label, industrial instrument, and so on.
More infor for you to know more
Features
No backlight, keeps displaying last content for a long time even when power down
Ultra low power consumption, basically power is only required for refreshing
Standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards, Jetson Nano
SPI interface, for connecting with other controller boards like Raspberry/Arduino/Nucleo, etc.
Comes with development resources and manual (examples for Raspberry Pi/Jetson Nano/Arduino/STM32)
Specifications
Operating voltage:3.3V~5V
Interface:SPI
Outline dimension:125.40mm ≠ 99.50mm
Display size:118.80mm ≠ 88.26mm
Dot pitch:0.198 ≠ 0.197
Resolution:600 ≠ 448
Display color:red, black, white
Grey level:2
Full refresh time:14s
Refresh power:26.4mW(typ.)
Standby power
Viewing angle:>170
Interface
SYMBOL DESCRIPTION
VCC 3.3V~5V
GND Ground
DIN SPI MOSI pin
CLK SPI SCK pin
CS SPI chip selection, low active
DC Data/Command selection (high for data, low for command)
RST External reset, low active
BUSY Busy status output, low active
Explanation
1. Refresh time:This refers to the global refresh time, that is, the time it takes to refresh each frame of the image; if the ink screen itself supports partial refresh, the partial refresh time is about 0.3 seconds
2. Pi interface:based on the standard interface design, suitable for Raspberry Pi Zero / Zero W / Zero WH / 2B / 3B / 3B +
Package Included:(raspberry pi board not included)
5.83inch e-Paper (B) x1
e-Paper Driver HAT x1
RPi screws pack (2pcs) x1
PH2.0 20cm 8Pin x1
Weight | 0.143 kg |
---|
Customers Also Viewed
5pcs ESP-32S Matching Adapter Board WIFI bluetooth Module ESP-WROOM-32 Module for DIP
$9.84Smart ModuleAdd to cartFeaturesESP-32S supporting adapter board, 2.54mm pitch, lead RESET and IO 0 port, can be inserted into the breadboard, use DuPont wire leads, etc., to facilitate development and debugging.Package Included5 x ESP-32S Matching Adapter Board
5 Channel Flame Sensor Module Analog Dgital Dual Output Fire Extinguishing Robot Flame Alarm System Module
$13.11Sensor & Detector ModuleAdd to cartFeatures1.Using a five-way flame sensor design, the detection range is wide (the detection range of a common single flame sensor is about 30°, and the range is gradually reduced as the distance increases, the detection range of this product is greater than 120°)2.Can output digital signals (high and low level), easy to use3. can output …
600W Mini 2CH HiFi Digital Audio Stereo Amplifier Bass bluetooth FM Radio Amplifiering Equipment
$109.34Switch AccessoriesAdd to cartSpecificationsColor:BlueType:Support bluetoothInput voltage:220V-240V 50/60Hz 12V(in car)Plug:US plugRated power:80W+80WPeak power:300W+300WChannel:2 CHLoad impedance:4-16ΩSNR:>90 dbFM frequency:88-108MHzDistoration rate:0.05%Frequency:20Hz-20KHz(±3dB)Total harmonic distortion:less than 0.5% (normal operating conditions)Signal input sensitivity:200MV (±30MV)MIC input sensitivity:9mV (±2mV)Record level output:1VAuxiliary output level:1VSensitivity:0.25mV-220mVRC power supply:CR2052 battery(built-in)Features-Mini HIFI digital bluetooth audio power amplifier.-SD Card, U disk, MP3 format play, support bluetooth wireless connection.-Supports FM stereo radio.-Two microphone input …
Reviews
There are no reviews yet.