10pcs MP-4 Gas Sensor Methane Sensor Detecting Combustible Methane Gas at Semiconductor Combustible DIY for Safety Detection System
$41.90
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Overview
The MP-4 methane sensor uses a multi-layer thick film manufacturing process to fabricate a and a metal oxide semiconductor gas sensing layer on both sides of a Al2O3 ceramic substrate, which are packaged in a metal case. The conductivity of the sensor changes when there is a detected gas in the ambient . The higher the concentration of the gas, the higher the conductivity of the sensor. This change in conductivity can be converted to an output signal corresponding to the gas concentration using a simple circuit.
Characteristics
The sensor has good sensitivity to methane in a wide concentration , and has the advantages of strong anti-interference ability, low power consumption, quickly response recovery, good stability, long life, low cost, and simple driving circuit.
Application
– Combustible gas leak monitoring device for home,factory,commercial use, fire/safety detection system.
– Combustible gas leak alarm, gas leak detector.
Note:The above figure shows the basic test circuit of the MP-4 sensor. The sensor requires two voltages to be applied:voltage (VH) and test voltage (VC). The VH is used to provide a specific operating temperature for the sensor, either DC or AC. The VRL is the voltage across the load resistor (RL) of the sensor in series. VC is the voltage for testing the load resistor RL and requires a DC power supply.
Package Included
10 x MP-4 Gas Sensor Methane Sensor Detecting Combustible Methane Gas
Weight | 0.02 kg |
---|
Customers Also Viewed
100 Pcs Copper Cable Lugs Kit SC6-6 ~SC35-10 Electrical Terminal Block Wire Connectors
$70.86ConnectorsAdd to cartSpecificationModel:SC6-6~SC35-10Material:Tin Plated CopperColor:SilverSize:6mm²/10mm²/16mm²/25mm²/35mm²Mount Hole:6 mm/8 mm/10 mmBox Size(L*W*H):280 x 126 x 14 mmQuantity:100 PcsFeaturesElectro-plated tin exterior.Premium quality copper material, environmentally friendly, safe for using.These tube lugs have a bell shaped end allowing for easy insertion of the cable.Acceptable working temperature is -55℃ to 100℃ and are suitable for applications in the Australian Climate.Copper lugs are …
100 Pcs Copper Cable Lugs Kit SC6-6 ~SC35-10 Electrical Terminal Block Wire ConnectorsRead More
TDA7377 Subwoofer Amplifier Audio Board 38Wx3 Mini Home Amp 2.1 Channel HiFi Stereo Power Amplifier DIY
$21.86Amplifier BoardAdd to cartDescriptionThe power amplifier board uses 7377 amplifier chip, dual circuit design, optional DC12V / AC12V power supply, and uses 2.1 three-channel output. Available for Bluetooth / Wireless Microphone / Fan. Separate design, easy installation, provides volume and subwoofer adjustment. ParametersWorking voltage:DC12V / AC12V Chip:TDA7377 Op amp:LT084 / 324 Working voltage:DC12V / AC12V Output power:38Wx3 Channel …
XH-W1411 220V 10A Smart Electronics LED Digital thermometer Temperature Controller Switch Module
$17.48Test & Measuring ModuleAdd to cartSpecificationsTemperature range:-55- + 120→Temperature measurement accuracy:± 0.3→Resolution:0.1→Temperature range:-19 ~ 99→Control accuracy:1→Temperature probe:NTC10K / B3950 comes standard with 1 meter waterproof probeSupply voltage:220VTemperature:-25 ~ 55→ Humidity 20% -85% (non-condensing)Output Type:10A relay outputsSize:90*60mm/3.54 Inch*2.36 InchHole size:70*50mm/2.76 Inch*1.96 InchFeatures– The board and plastic panels fixed column compartment and lock nut– Connect the power supply according to the drawings …
3Pcs HIFI Amplifier Passive Tone Board Bass Treble Volume Control Preamp Board DIY Kit
$24.99DIY Electronic KitsAdd to cartDescriptionIt is DIY Kit, must be assemble to work. User need technical operation ability.Package included3 x HIFI Amplifier Passive Tone Board Bass Treble Volume Control Preamp Board DIY Kit
100x100cm High Strength Carbon Fiber Cloth for interlayer 3900 mpa
$60.74Carbon FiberAdd to cartSpecificationSize;100 x 100cmWidth; 0.25mmMaterial:Carbon fiberCompressive strength:3900 mpaFeaturesa.Uniform texture, without color. Weaving skills, good gloss.b.Mainly used in aircraft main, tail and body; automotive engine synchronizer, hood, bumpers, decorative pieces; bike frame, wheels, leading; racket, cone; kayaking, snowboarding; various models, helmets , watches, pens, bags.Main purpose1. Aerospace:fuselage, rudder, rocket engine shells, missiles casual flow, such as solar …
100x100cm High Strength Carbon Fiber Cloth for interlayer 3900 mpaRead More
3pcs EQKIT 60 Seconds Electronic Timer Kit DIY Parts Soldering Practice Board
$28.54DIY Electronic KitsAdd to cartInstruction:http://img.staticbg.com/file/products/20180726215941ETI-60-timer-kit.pdfFeatureOperating voltage:DC5VStandby current:≤8mAWorking current:≤10mACountdown:60 secondsCountdown ends prompt:three alarmsSoludering difficulty:GeneralBoard size:84 x 84mmNote:Electronic production kit, require buyer soldering assembly.Package included3 x Electronic Timer K
Reviews
There are no reviews yet.