Modbus RTU Octal Relay Module RS485 / TTL UART 8 inputs 8 Outputs Switch Board
$41.54
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Size Conversion
Inches
Centimeters
Please according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.
Manual:Click here to open
Feature
1. Onboard mature and stable STM8S103K3T6 MCU and MAX485 level conversion chip
2. Communication protocol:support standard Modbus RTU protocol
3. Communication interface:support TTL UART interface with RS485 / 5V level
4. Communication baud rate:4800/9600/19200, default 9600bps, support to save after power off
5. The signal range of optocoupler input:DC3.3-30V (this input cannot be used for relay control)
6. Output signal:relay switch signal, support manual, flash off, flash off mode, flash off / flash delay base is 0.1S, maximum flash off / flash time can be set to OxFFFF * 0.1S = 6553.5S
7. Device address:range 1-255, default 255, support to save after power off
8. Baud rate, input signal, relay status, device address can be read using software / command
9. On-board 8-channel 5V, 10A / 250v AC, 10A / 30vDC relay, which can be continuously attracted 100,000 times, with diode bleed protection, short response time
10. Onboard relay switch indicator
11. STM8 SWIM program is reserved for programming, supporting customers to download their own firmware for secondary development
12. Power supply voltage:DC7-30V, 5.08mm terminal power supply
Package includes
1 x Realy board
1. VCC, GND:DC7-30V 5.08mm power input terminal
2. DC3.3-30V optocoupler signal input
IN1-IN8:Positive channel 1-8
GND_IN:Channel 1-8 common negative
3. A+, B-:RS485 communication interface, A +, B- are connected to A +, B- of external control terminal respectively
4. 5V, SWIM, GND, NRST:STM8 SWIM program download port
5. TXD, RXD, GND:TTL level UART communication interface, TXD, RXD, GND are connected to RXD, TXD, GND of the external control terminal, only support 5V level TTL module / MCU. Use wiring order suggestion:Modbus Power-Modbus module connects to TTL module-TTL module is powered on
6. RST:MCU reset button
7. Relay switch signal output
NO:Normally open, the relay hangs before pull-in, short-circuit with COM after pull-in
COM:Common
NC:Normally closed end, the relay is short-circuited with COM before pull-in, and hangs up after pull-in
Weight | 0.154 kg |
---|
Customers Also Viewed
3 Axis GRBL USB Driver offline Controller Control Module LCD Screen w/ Controller Board SD Card for CNC 1610 2418 3018 Wood Router Laser Engraving Machine
$93.14Control BoardAdd to cartDescriptionThis offline controller w/ controller board is designed for the use of Mini CNC router 1610/2418/3018 and even with more advanced function of tool set, limit switch supportive, Laser supportive; Offline and Bluetooth supportive.SpecificationUSB Cable Length:20cmFirmware:GRBL 08, 09, 1.1 and so on Input Voltage:DC 7V- 36VApplicable CNC Router:3 Axis CNC router 1610; 2418; 3018Features1. Support …
20Pcs PS2 Game Joystick Switch Sensor Module
$34.87Other Module BoardAdd to cart20Pcs PS2 Game Joystick Module For Description This is PS2 game joystick module for Lots of robot projects need joystick. This module provides a affordable solution to that. Simply connect to two analog inputs, the robot is at your commands with X,Y control. It also has a switch that is connected to a digital pin. …
Ebyte E07-M1101D-TH 10dBm Spring Antenna 433MHz CC1101 Wireless Transceiver SPI 433mhz RF Module
$9.18Smart ModuleAdd to cartSpecificationsInterface:SPIPower:10dBmDistance:520mSupply voltage:1.9 ~ 3.6V DCFrequency:433MHz(387 ~ 464MHz)RF Parameter:Value:RemarkWorking frequency:387~464 MHz:Default:433MHz (26MHz oscillator)Transmitting power:10 dBm:Max. Power (10mW)Receiving sensitivity:-108 dBm:Air data rate:0.6kbpsAir data rate:0.6k~500kbps:Default:0.6kbpsTest distance:600m:In open and clear air, with maximum power, 5dBi antenna gain, height of 2m, air data rate:0.6kbpsHardware Parameter:Value:RemarkSize15 * 30 mm Without Spring antennaAntenna typeSpring antenna Communication interfaceSPI PackageDIP Electronic parameter:Min.:Typ.:Max.:Unit:ConditionPower supply:1.8:3.3:3.6:VCommunication level:1.8:3.3:3.6:VTransmitting …
Waveshare IS62WV51216BLL SRAM RAM Module Storage Memory Board
$28.42Expansion Board & ShieldAdd to cartFeatureFunction:SRAM IS62WV51216BLL (8M Bit), can be directly connected to the corresponding FSMC interface of the Open series development board, and the external expansion interface supports external expansion of SRAM, LAN, USB HOST, etc.Typical application:SRAM external expansion storageMain resources:IS62WV51216BLL (8M Bit), control interfacePackage includes1 x IS62WV51216BLL SRAM Board
3 Megapixel Optical Zoom Cam Module Fixed Focus 3MP OV3660 Camera Module FOV 79
$15.30Other Module BoardAdd to cart>>>Manual:Click here to openSpecificationsModel No.:HBVCAM-3M1917Model Size:30mm ≠ 25mm ≠ 5.0mm÷0.2MMTemperature (Operation):-30C to 70CTemperature (Stable Image):0C to 50CAssembly technique:SMT (ROSH)Focus:FixedObject distance:30CM-infinityResolution:800LW/PH (Center)PCB printing ink:Blackinterface:USB 2.0Power supply:USB bus powersupply voltage:DC 5V÷5%Maximum Power consumption:600WOperating system request:Win XP/win 7,8 / vista /android 4.0/ mac /Linuxwith uvc Sensor:OV3660 (1/5” )Seneor Package:CSP,Bare DieMaximum resolution:2048*1536Sensitivity:670mV /(lux-sec)Pixel Size:1.4┢m x 1.4┢m Maximum Image Transfer …
3 Megapixel Optical Zoom Cam Module Fixed Focus 3MP OV3660 Camera Module FOV 79Read More
Hall Effect Magnetic Sensor Module DC 5V
$4.36Sensor & Detector ModuleAdd to cartDescription This is Hall Effect magnetic sensor module DC 5V for Brand:KEYES Model:KY-003 Magnetic, speed, gap induction Suitable for DIY project Working voltage:DC 5V Material:PCB Feature Small size and high sensitivity. response temperature and good performance. Precision and high reliability 3144 Series Hall principle of Hall effect switch IC, using technology to produce magnetic semiconductor …
Geekcreit Portable Mini Automatic Spot Welding Machine Control Board 12V/5.6V Portable Lithium Battery Spot Welding Circuit Board Accessories
$40.49Driver ModuleAdd to cartInstructions for use of automatic spot welding control board1. Power requirements:In 12V mode, voltage input is 7-15V (12V recommended), in 5.6V capacitor mode, voltage supports 3.7-6V (recommended 5.6V), current requirements:can output actual current 120-360A2. Button function:switch between 1 power level-2 power level-3 power level-4 power level after long press for 3 seconds3. The red light …
Reviews
There are no reviews yet.