3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
300W Digital Amplifier Speaker Protection Board 2.1 Channel Relay Speaker Protection Module Boot Delay DC Protection
$15.30Relay ModuleAdd to cartFeatures1.With delay and DC protection (default 1.8V control, DC sensitivity can be adjusted)2. This common power DC protection board uses an optocoupler. Since the optocoupler has input and output isolation,3. Electrical signal transmission has the characteristics of unidirectionality, so it has good electrical insulation and anti-interference ability.4. Since the input end of the optocoupler belongs …
AB18 2SA1943/2SC5200 High Power 300W + 300W Dual Channel Class A/B Power Amplifier Board for Sound Speaker DIY
$125.17Amplifier BoardAdd to cartProduct description1. Using Japan imported original brand new 2SA1943/2SC52002. Electrolytic capacitor adopts imported electrolysis to ensure strong continuous power support.3. The resistor uses high-precision resistors, and the main circuit uses high-precision resistors with an accuracy of ÷ 1% to ensure a good signal-to-noise ratio for the whole machine.4. The PCB adopts 1.6mm thick double-sided sheet, …
5pcs DMP-L1 WiFi intelligent Lighting Module Built-in ESP ESP8285 WiFi Chip for Smart Home
$28.82Smart ModuleAdd to cartDescriptionThe core processor of DMP-L1 module adopts industrial chip ESP8285. The chip integrates an enhanced version of the Tensilica’s L106 Diamond Series 32-bit core processor in smaller size packages. ESP8285 has a complete Wi-Fi network function, which can be used independently from the controller. Its built-in cache memory greatly provides CPU performance.DMP-L1 module supports standard …
5pcs DMP-L1 WiFi intelligent Lighting Module Built-in ESP ESP8285 WiFi Chip for Smart HomeRead More
Wareshare 5.5 inch AMOLED HDMI Display Capacitive Touch Screen with Tempered Glass Support for NVIDIA Jetson Nano Raspberry Pi
$229.66Display ScreenAdd to cartDocumentsManual:Click here to openDatasheet:Click here to openSoftwarePanasoni SDFormatterWin32DiskImagerPuTTYOverviewThis product is a universal 5.5-inch HDMI display with 1080≠1920 ultra-clear resolution and a capacitive touch panel. Support for Raspberry Pi and various mini PCs, also as a computer monitor.Features5.5inch AMOLED, 1080×1920 resolution.Toughened glass capacitive touch panel.Supports popular mini PCs such as Raspberry Pi, as well as general …
5pcs 20x20x15mm DIY CPU IC Chip Heat Sink Extruded Cooler Aluminum Heat Sink
$4.36Electronic Accessories & SuppliesAdd to cartFeatureAluminum heat sinks for electronics, computers, electrical facilities, play a cooling effectSpecificationMaterials:AluminumSize:20*20*15mm (L*W*H)Color:SilverQty:5pcsPackage includes5 x CPU IC Chip Aluminum Heat Sink
5Pcs Yellow Backlight 1602 Character LCD Display Module
$24.89Display ScreenAdd to cartDescriptionLCD display module with yellow backlightWide viewing angle and high contrastBuilt-in industry standard HD44780 equivalent LCD controllerCommonly used in:copiers, fax machines, laser printers, industrial test equipment,networking equipment such as routers and storage devicesLCM type:CharactersCan display 2-lines X 16-charactersOperate with 5V DCModule dimension:80mm x 36mm x 12mmViewing area size:64.5mm x 16mmPackage included5 X LCD display module
Bathtub Caddy Bamboo Bath Tub Holder Bathroom Tray Glass Book Reading Rack Stand
$106.76FoamAdd to cartSpecificationMaterial:BambooColor:WoodSize:(L)X(W)X(H)105X22X4cm/41.34inchX8.66inchX1.57inch(appr.)Features1. Constructed from durable bamboo and metal supporting frame in excellent craftsmanship for many years use.2. Varnish processing on surface, lightweight and easy to operate.3. Books can be held with metal rack stably for reading when bathing.4. Books, phone, towl, and food can be placed on it for convenient reach.5. Its length is adjustable between …
Bathtub Caddy Bamboo Bath Tub Holder Bathroom Tray Glass Book Reading Rack StandRead More
Reviews
There are no reviews yet.