3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
OpenMV OpenMV3 4 2 Camera Module M7 H7 LCD Expansion Board Display Screen Module
$50.02Display ScreenAdd to cartnullFeatureThe LCD Shield gives your OpenMV Cam the ability to display what it sees on-the-go while not connected to your computer. It features a 1.8inch 128×160 16-bpp (RGB565) TFT LCD display with a controllable backlight. Your OpenMV Cam’s firmware has built-in support for controlling the LCD Shield using the LCD module.ApplicationsThe LCD Shield is great …
OpenMV OpenMV3 4 2 Camera Module M7 H7 LCD Expansion Board Display Screen ModuleRead More
3pcs MFRC-522 RC522 RFID RF IC Card Reader Sensor Module Solder 8P Socket
$10.96Sensor & Detector ModuleAdd to cartIntroduction to the RFID moduleThe MF522-AN module adopts MFRC522 original chip design card reader circuit, which is easy to use and low in cost. It is suitable for users of advanced applications such as device development and card reader development, and users who need to design/produce RF card terminals. This module can be directly loaded …
3pcs MFRC-522 RC522 RFID RF IC Card Reader Sensor Module Solder 8P SocketRead More
Transparent Acrylic Sheet Housing Module Case for DSO138 Oscilloscope
$17.48DIY Electronic KitsAdd to cartFeatureThis product is for DSO138 Oscilloscope only. (Product ID:984002, 969762)Color:TransparentMaterial:AcrylicInstallation size:12.7 x 8.7 x 2.6 (L*W*H)Note:Package does not includes the DSO138 Oscilloscope.Instruction:Click to openPackage includes1 x DSO138 Transparent Acrylic Sheet
20Pcs 3V 650nM 5mW Line Laser Diode Module
$41.34Module ComponentsAdd to cartDescriptionSpot mode:line(Continuous output)Dimensions:diameter 9mm x length 23mmLaser working life:5000-10000 hours or moreLaser wavelength:650nmOutput power:5mWOperating voltage:DC3VWorking current:16mA ~ 20mAWorking temperature:-36 → ~ 65 →Storage temperature:-36 → ~ 65 →Level:sub-industrial gradeColor:red lightMaterial:brassApplication(1) industrial grade:can be used for equipment, health care, military, Kam pseudo security, stage lighting, tools, U disk, mobile phone, projection teaching flip pen, warm measuring …
MMDVM Open-Source Multi-Mode Digital Voice Modem DIY Kit Expansion Board for Raspberry Pi
$103.03Raspberry Pi & Orange PiAdd to cartDescription– This board could cooperate Raspberry Pi , Orange Pi, a variety of school development board to use.– Board has been applied in the GM300 GM3188 3688 950I 338 Vitex DR-1X, other types of repeaters and car stations need to be studied yourself.– The MMDVM is intended to be an open-source Multi-Mode Digital Voice Modem,which …
MMDVM Open-Source Multi-Mode Digital Voice Modem DIY Kit Expansion Board for Raspberry PiRead More
3Pcs 5V-30V DC PWM Speed Controller Mini Electrical Motor Control Switch LED Dimmer Module
$10.04Other Module BoardAdd to cartFeaturePWM DC motor speed controller is a very safe product.When the situation is overcurrent, it will disconnect by itself. after cooling off a few seconds, the fuse will recovery automatically.With high voltage and high current resettable fuseMini but usefulSpecificationOperating voltage:DC 5-30VControl power:90W (maximum)Quiescent current:0.015A (standby)PWM duty cycle:1% -100%PWM frequency:10khzSize:29mm*23mm (excluding handles)Total height:15mmKnob color:Send randomlyPackage included3 …
3Pcs 5V-30V DC PWM Speed Controller Mini Electrical Motor Control Switch LED Dimmer ModuleRead More
Reviews
There are no reviews yet.