3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
5Pcs CP2102 USB To TTL/Serial Module Downloader
$21.98Converter BoardAdd to cart5Pcs CJMCU CP2102 USB To TTL/Serial Module UART STC Downloader For Driver Installation Introduction:http://forum.hobbyant.com/forum-topic-56275.html Description CJMCU-CP2102 its highly integrated, built-in USB2.0 full-speed function controller, USB transceiver, crystal oscillator, EEPROM and asynchronous serial data bus (UART), supports full-featured modem signal without any external USB devices. CJMCU-CP2102 works with other USB-UART adapter circuit similar to the driver …
10pcs 180 Degree USB 3.0 Type A female Socket Connector SMT Charging Socket Plug Connector
$10.11Terminal BlocksAdd to cartSpecificationsColorBlueRated Current1.5ARated Voltage30VInsertion Force35N MaxDurability3000 Cycles Min Rubber CorePBT / Icp Ul94V-0 Resistance To Voltage500V Ac Min. Insulation Resistance≥1000MΩPull-Out Force10N Min.Initial 8-20N AfterWorking Temperature-20 Degrees To 60 Degrees Contact Impedance≤30mΩTerminalsBrass C2680,Nickel Base,Gold-Plated 1 u,Package included-10pcs X 180Degree Connectors
Dual Servos Knob Serial Port Control Board Futaba MG995 SG90 Steering Gear Debugging Module
$13.11Other Module BoardAdd to cartFeature1. The onboard stable 8-bit MCU is used to generate high-resolution PWM signals with precise control.2. Support manual mode and return to medium mode, switch by button, with mode indicator.3. Support knob adjustment or serial command control in manual mode.4. The serial port command control can use the matching host computer software or connect to …
Dual Servos Knob Serial Port Control Board Futaba MG995 SG90 Steering Gear Debugging ModuleRead More
Keyes Brick Laser Head Sensor Module (pad hole) with Pin Header Board Digital Signal
$4.36Sensor & Detector ModuleAdd to cartDescriptionThis sensor is fully compatible with ARDUI NO single-chip microcomputer, and its connection port is also compatible with Arduino sensor expansion board. It is mainly composed of a laser head, which is composed of a light-emitting tube core, a condenser lens, and a copper adjustable sleeve. After connecting to the power supply, we directly input …
Keyes Brick Laser Head Sensor Module (pad hole) with Pin Header Board Digital SignalRead More
5pcs DC3~5V AK-119 433.92MHZ 4 Pin Superheterodyne Receiver Board without Decoding -105dBm
$10.37Other Module BoardAdd to cartFeatures1. The product is small in size, high in sensitivity and strong in anti-interference ability;2. The same definition as the four-pin pin of RXB12, the usage is the same. The unit price is lower than RXB12 and can be directly replaced.Technical ParametersWorking voltage:DC3~5VTransmission rate:4.80KBPSQuiescent current:6mAReceive sensitivity:-105dBmDimensions:30 * 9 * 5mmWorking temperature:-20 ° C ~ +80 …
5pcs DC3~5V AK-119 433.92MHZ 4 Pin Superheterodyne Receiver Board without Decoding -105dBmRead More
150g Capacity Quartz Silica Melting Crucible Pot for Gold Silver Platinum Refine
$16.19Glassware KitAdd to cart150g Capacity Quartz Silica Melting Crucible Pot For Gold Silver Platinum RefineDescriptionMaterial:quartzCapacity:150gDiameter:43X57mm/1.69inch X2.24inch(ID*OD)Height:20mm/0.79inchDeepth:15mm/0.59inchNet Weight:40gFeatureQuartz silica melting crucibleProduced by modern ceramic processing technologyHigh orrosion resistance and strength,the temperature resistance up to 2800℃/5072FPerfect for gold silver casting and refine usagePackage included1X Quartz Silica Melting Crucible
WXD3-13-2W Precision Potentiometer 470R 470 Ohm Wirewound Multi-Turn Potentiometer
$4.50Module ComponentsAdd to cartSpecificationsResistance range:470┯Resistance tolerance:÷ 5%Rotation angle:3600 ÷ 20 Number of laps:10 lapsRated voltage:160VStarting torque:3.5 ~ 100mN.mRated power:2W (85 →) 0W (125 →)Linearity accuracy:÷ 0.3%Mechanical durability:10,000 weeksPackage included1 x Potentiometer
Reviews
There are no reviews yet.