3Pcs J03 LED Digital Time Delay Relay DC 6-30V on off Trigger Delay Timming Timer Switch Micro USB Power Supply 5V 12V
$32.79
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Wide voltage power supply (6 ~ 30V), supports microUSB 5.0V power supply, easy to use;
2. The interface is clear and simple, powerful, easy to understand, meet almost all your needs;
3. The emergency stop function (“STOP’key);With reverse polarity protection, reverse polarity will not burn the product.
4. Increase the sleep mode, if this mode is enabled, without any operation within 5 minutes, then automatically turn off the monitor, any key wake-up;
5. You can set a different OP, CL, LOP parameters, which are independent of each other, and are automatically saved;
6. After the module is powered down, all parameter settings are not lost.
Product parameters
1:Operating voltage:6–30V, support microUSB 5.0V power supply
2:Trigger Source:Active-high (3.0V-24V), have optocoupler isolation, can improve the system’s anti-jamming capability (customers can also shorting common ground).
3:Output capability:You can control the DC 30VDC 5A or 220VAC 5A device.
4:Quiescent Current:20mA; Operating Current:50mA
5:Life:more than 10 million times; Working temperature:-40→-85 →; Size:6.2*3.8*1.7cm.
6:With optocoupler isolation, enhanced anti-jamming capability, industrial grade board.
Special Note:The relay outputs are passive contact, just a switch.
Operating mode
P1:trigger signal, the relay is on ‘OP’ time, and then disconnect; in the ‘OP’ time, as follows
P1.1:signal is triggered again, invalid
P1.2:signal is triggered again, the clock is reset
P1.3:Signal trigger again, relay off, stop the clock;
P-2:trigger signal, the relay off ‘CL’ of time, the relay on ‘OP’ time, and then disconnect relay;
P3.1:trigger signal, the relay is turned on after the ‘OP’ time, the relay off ‘CL’ time, then the operation cycle, if the trigger signal period, the relay off, stop the clock; the number of cycles ( ‘LOP ‘) can be set.
P3.2:without triggering signal, the relay is on ‘OP’ time, the relay off ‘CL’ time, and has been cycling; frequency ( ‘LOP’) cycle can be set;
P-4:signal holding function. If there is a trigger signal timing is cleared, the relay remains on; when the signal disappears, after the timing ‘OP’ time, the relay is; if another signal during timing, timing is cleared.
Timing range
0.1 seconds (min) to 999 minutes (max) continuously adjustable
How to choose the time range
After setting the mode selection screen parameter value by a short press ‘STOP’ button to select the time range;
XXX. decimal point in the unit place, time range:1 second to 999 seconds.
XX. X decimal point in decade place, Timing range:0.1 seconds to 99.9 seconds
X. X. X. decimal full brightness, Timing range:1 minute to 999 minutes.
For example, you want to set ‘OP’ is 3.2 seconds, then move the decimal point to decade place, the digital display 03.2
Parameter description:’OP’ – conduction time, ‘CL’ – off time, ‘LOP’ – the number of cycles (1-999 times, ‘—‘ represents infinite loop).
These parameters are independent of each other, but is shared by each mode. For example, in P1.1 mode, set the on-time ‘OP’ is 5 seconds, if you switch to P1.2 mode, it’s ‘OP’ will be 5 seconds too.
In the main interface (display 000), short press ‘SET’ button will display ‘OP’ ( ‘CL’, ‘LOP’) and the corresponding time XXX;
Some parameters only mode ‘OP’ (such as the mode P1.1, P1.2, P1.3), short press the ‘SET’ key to display only the “OP” and the corresponding time;
Some models have parameters ‘OP’,’CL’, ‘LOP’ (such as the mode P3.1, P3.2), short press ‘SET’ button will display ‘OP’ and the corresponding time, “CL” and the corresponding time, “LOP” and the corresponding number of times;
In the main interface by short press ‘SET’ key to see information about the parameters of the current mode, very convenient!
How to set parameters
1. First, read the instructions to determine the required operating mode.
2. The module is powered up, the display at the current work mode (P1.1 default mode), then enter the main interface; press ‘SET’ button for 2 seconds after release to enter mode selection interface; a short time by pressing ‘UP’, ‘DOWN’ key to select the mode (P1.1 ~ P-4).
3. Select the mode (such as P3.2), short press the ‘SET’ button, then the parameter to be set flashes ( ‘OP’on-time, ‘CL’ off time, ‘LOP’ cycles ( ‘—‘ represents infinite loop)), by ‘UP’, ‘DOWN’ keys to adjust the parameter value, support long press (rapid increase or decrease) and short press (increase or decrease one unit); then short press the ‘STOP’ key to select the decimal point position, select the time range (0.1 seconds to 999 minutes); short press the ‘SET’ button to set the next parameters of the current mode of procedure is as above.
4. After the parameters are set, long press ‘SET’ button for 2 seconds then release, the name of the current mode will flash once, and then return to the main screen, set the parameters of success!
The main interface:In the relay does not work status display ‘000’ (no decimal point), with a decimal point under relay state.
Mode selection screen:Long press the ‘SET’ key to enter, after setting is completed, long press the ‘SET’ key to exit back to the main screen.
‘STOP’ button extensions
Relays enable mode
1. ON:Relay allows conduction in the ‘OP’ on-time;
2. OFF:relay prohibit conduction is always closed;
In the main interface, short press the ‘STOP’ button to switch between ON and OFF, the current in which the state will flash, and then return to the main screen. (This feature is an emergency stop function, click off the relay)
Sleep mode
1. ‘C-P’ Sleep mode:five minutes without any operation, the digital display automatically turns off, the program running as usual;
2. ‘O-d’ normal mode:digital display always open;
Press the ‘STOP’ button for two seconds and then release to switch ‘C-P’ and ‘O-d’ state, in which the current state of flashes and then return to the main screen.
Package Included
3 x DC 1 Channel Time Delay Relay Module
3 x Shell Case
Weight | 0.222 kg |
---|
Customers Also Viewed
Robotdyn SAMD21 M0-Mini 32 Bit ARM Cortex M0 Core 48 MHz Pins Soldered Development Board
$38.30Motherboard & Development BoardAdd to cartDimensional drawing:Click to openPinout:Click to openSchematic:Click to openTechnical ParametersMicrocontroller:ATSAMD21G18 48pins LQFPUSB-TTL converter:SAMD21 MCUPower Out:3.3V-800mAPower IN. USB:5VPower IN. VIN/DC Jack:5VPower Consumption:3.3V 220mALogic Level:3.3VUSB:Micro USBClock Frequency:48MHzOperating Supply Voltage:3.3VDigital I/O:20(7-PWM)Analog I/O:6Data RAM Type/Size:20KbData ROM Type/Size:128KbInterface Type:ISPOperating temperature:−40㎡°/+85㎡°Length*Width:56.5*18mmFeatureThe RobotDyn SAMD21 M0-Mini represents a powerful, 32-bit extension of the Ard-uino U NO platform, but to small size like Micro or …
Robotdyn SAMD21 M0-Mini 32 Bit ARM Cortex M0 Core 48 MHz Pins Soldered Development BoardRead More
CDCPH Super Capacitor 16v16.6f Automotive Rectifier Farad Capacitor instead of 16v20f
$32.43Electronic Accessories & SuppliesAdd to cartDescriptionVoltage:15-16 VCapacity:16.6 to 18 FWorking Temperature:-20-70 →Volume:62 Long 120 * Height * Thick 20MMMain performance:low ESR feature, large current can replace the battery.Package included1 x 16V16. 6F Supercapacitor
5pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board without Shell
$31.91Test & Measuring ModuleAdd to cartSize ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.Product Highlights1.With soft-start function, the output voltage increases slowly and there is no inrush current, which can effectively extend the life of the fan motor or LED tube.2.The NC voltage regulation is …
5pcs 5V USB Cooling Fan Governor LED Dimming Module Low Power Timer Board without ShellRead More
T05-5500 5500mW 445nm Blue Laser Module TTL&PWM Modulation 2.54-3P+2.54-2P for EleksMaker DIY Laser Engraver
$263.24Laser ModuleAdd to cartSpecificationGeneral Specification Model:T05 Heatsink Material:Aircraft Aluminum Luminous Color:Blue Section Size:43mm x 43mm Cooling Mode:Heat Sink Groove, Cooling Fan Dimension:76 * 43 * 43mm Adapter Plug:US Plug Adapter Input Voltage:AC 100-240V Adapter Output Voltage:DC 12V 5A Can Engrave:MDF/Balsa/Paper/Wood/Fabric/Plastic/Leather/Plywood/Foam Paper/Anodized Aluminum Can Not Engrave:Metal/Glass/Stone/Ceramics/Stainless Steel/Reflective Material/ Transparent Material Technical Parameters Laser Power:5500mW Wavelength:445nm Beam Shape:Dot (Focusable) Working …
6S-JW12 6S 22.2V Polymer 18650 Lithium Battery Protection Board 14A Working Current 25.2V without Balanced
$5.79Battery Protection ModuleAdd to cartSpecificationContinuous discharge current:14AInstant discharge current:22ALithium battery charger:25.2VCharging current:25 (max)AOvercharge detection voltage:4.28 ÷0. 05 V single coreOvercharge protection delay:0.5SOvercharge release voltage:4. 08 + 0. 05V single coreOver-discharge detection voltage:2.55 + 0.08VOver-discharge detection delay:0.1SOver-discharge release voltage:2.9÷0.1VOvercurrent detection voltage:150mVOvercurrent detection delay:10mSOvercurrent protection current:75÷5 AOvercurrent protection release condition:disconnect the loadShort-circuit protection conditions:external load short-circuitShort circuit detection delay:250uSShort-circuit protection release …
Reviews
There are no reviews yet.