5pcs 3V/3.7V To 5V 1A Lithium Battery Step Up Module Board Mini Mobile Power Boost Charger Module with Undervoltage indication
Shipping:Standard Shipping about 10-25 business days
1. Using high quality chips and expanding MOS tubes.
2. The output current is expanded to 1A, and the maximum output is 1.5A. The 2A Schottky diode is used to recharge the balance.
3. With the new scheme design, the circuit design does not require electrolytic capacitors and tantalum capacitors (the electrolytic capacitors have a short life and the tantalum capacitors are in danger of explosion). 3 ceramic capacitors (MCC) used in high-end circuits.
4. The same load indicator and undervoltage indication (when the battery voltage is less than 2.7V, the indicator will go out under load, when the battery voltage is greater than 2.7V with load, the indicator light is on, when there is no load, the indicator light is micro bright).
5. Ultra-small size, 14.1*18.8*5.5 mm.
6. The circuit conversion efficiency is high, the efficiency is higher than 90%, and the efficiency of the single-cell lithium battery is also less than 80%.
7. Input low power reverse connection protection. If your battery has 2A protection board, the protection board will protect when you input the positive and negative poles of the power supply. Note that when there is no protection board or the input current is greater than 2A, the input reverse connection protection Will fail, will cause the module to be damaged, remember.
8. Ultra-low quiescent current, new version, quiescent current will be less than 100 microamps. No connection is required to connect to the battery.
Output current:rated 1A-1.5A (single-cell lithium battery input), maximum 1.5A (single-cell lithium battery input)
Conversion efficiency:up to 96% (the higher the input voltage, the higher the efficiency)
Output ripple:30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
Undervoltage indication:LED with load LED is on (input voltage is lower than 2.7V LED is off)
Operating temperature:industrial grade (-40 ° C to +85 ° C)
Full load temperature rise:30 ° C
Load adjustment rate:±1%
Voltage regulation rate:±0.5%
Dynamic response speed:5% 200uS
Short circuit protection:None, if you want to have short circuit protection, you can input the lithium battery protection board or use a protected lithium battery.
Input reverse connection protection:none
Input mode:IN+ input positive, IN- input negative
1).DIY a mobile power supply, you only need to input a battery power input, you can output 5V voltage to charge your mobile phone, MP3, MP4, PSP, very simple and convenient.
2). Power your electronic equipment. When your equipment needs 5V power supply, but now you only have lithium battery power supply, use this module to directly boost to 5V, solve your troubles.
3). The system is powered by the front stage. When you input the battery (1-5V) when you are working on a project, and your system board needs 5V stable power, then you choose this module will be your most. Good choice, you can work without commissioning directly on the machine, easily achieve high efficiency and high power boost.
Frequently Asked Questions and Answers
1. Why is my module designed to this shape
A:Our module is designed for your convenience. You can also remove the USB holder and solder the module directly to the PCB. The package is DIP-24.
2. How efficient is the module working I use it on the battery and it is very efficient. Can I use it
A:The efficiency of this module is very high in non-synchronous rectification. The highest efficiency of our test can reach 96%. There is also friends who do not blindly pursue high efficiency, high efficiency is proportional to the price, for example, you need 5V 0.5A power supply, 80% efficiency loss energy is 0.625W, 90% efficiency loss energy is 0.278W, Do you think it is necessary to double the cost of this 0.3W power It is ok to choose a combination.
3. Is this power module short-circuit protected When I use it, I accidentally output a short circuit and it will burn out
A:There is no short circuit protection. If you need short circuit protection, please connect the self-recovery fuse in series at the input.
4. Does this power module have input reverse connection protection When I use it, I accidentally input the power supply and it will burn out when I reverse it.
A:There is no reverse protection
5. Can this module current run at 5V 500mA for a long time
A:This module has a design power of 2.5W. It can run for a long time at 2.5W, and 5V*0.5A=2.5W can be operated for a long time. .
6. I need a current of about 2A. Can this module work in parallel
A:Direct parallel connection is not possible. There will be a large circulation between them. If you want to output parallel operation, you need to adjust the voltage of each module to a uniform error of less than 50 mV, so that it can work. Care should be taken to avoid overloading a single module and the output power should not exceed 70% of the total power of the module.
7. What is the working temperature of this module, can it reach the industrial level
A:Yes, the working temperature is -40 to 85 degrees.
Customers Also Viewed
5.8g 15dBi Directional Small Flat Antenna FPV Image Transmission Receiver with High Gain inner Hole$24.04RF amplifierAdd to cart
FeatureModelFrequency range-MHz5005-6000Bandwidth-MHz750Gain-dBi15Vertical lobe width –40Horizontal lobe width –40Front-to-back ratio -dB◎25Standing wave ratio1.5Impedance-┯50Polarization modeVerticalMaximum power-W100Connector modelSMAAntenna size-mm65*65Weight-Kg500gSupport rod diameter-mm40 ~ 50Package includes1x High Gain Panel Antenna
Square Solar Magnetic Levitation 4 Sides Mendocino Motor Horizontal Levitating Stand Educational$62.21ChemistryAdd to cart
SpecificationName:Solar Magnetic Levitation ModelMaterial:Acrylic, Magnets, Solar Panels, Copper Enameled WiresFeature:Automatic rotation under lightType:Horizontal Levitating Stand, Four-sided Solar PanelPrinciple:Photoelectric Effect, Electro-Magnetic InductionSpeed:300-1500 r/miniOverall Size:155*56*57mmFeatures– Laser-cutting acrylic material, no burrs, beautiful cruved lines.– Transparent visual structure, explain the principle and mechanism easily.– Unique magnetic levitation structure, almost frictionless.– Creative gifts, technological gifts, principle teaching models, fashion desktop …
5pcs Blue LED 22mm DC Voltage Measuring instrument Mini Voltagemeter DC6~100V AD101-22VM indicator Voltmeter$15.84Electronic Accessories & SuppliesAdd to cart
DescriptionMaterial:Electrical componentsColor:BlueShape:RoundVoltage:DC 6-100VSize:2.8*5cm/1.10inch*1.97inch (D*H)Note:Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!Package Included5 x 22MM Voltage Indicator
5pcs 24V ZFX-W2062 Microcomputer Digital Electronic Temperature Controller Fahrenheit Celsius Conversion Adjustable Digital Display$40.74Test & Measuring ModuleAdd to cart
SpecificationsTemperature range:-50~110°CResolution:0.1°C/-9.9~99.9; 1°C/otherMeasurement accuracy:0.1 ° CRefresh rate:0.5SHigh temperature protection:0-110 ° CInput voltage:24V DCMeasurement input:NTC (10K0.5%) waterproof sensorOutput:1channel 10A relayEnvironmental requirements:-10~60°C; humidity 20%-85%Size:48*29*32mmOpening size:46*26.5mmPower consumption:quiescent current Instructions for Use1. Connect the power supply and load, that is, supply power to the controller. At this time, the red color is displayed as the measured temperature, and the …
BESTEP 1 Channel 12V Relay Module High And Low Level Trigger$4.77Relay ModuleAdd to cart
DescriptionMaximum load:AC 250V/10A, DC 30V/10A.The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA.Working voltage:12V.Every channel of the module can be set high or low level trigger by jumper.Fault tolerant design, even if the control line is disconnect, the relay will not act.Power indicator (green), 1 relay status indicator (red).The interface design is …
ESP8266 ESP-01 ESP-01S DS18B20 Temperature WiFi Wireless Node Module internet of Things$6.55Expansion Board & ShieldAdd to cart
Size ConversionInchesCentimetersPlease according to your own measurements to choose your suitable size. The tags inside the items will show in our Asian (Type) size.FeatureThis ESP-01/ESP-01S DS18B20 Temperature module based on the ESP8266 and digital temperature module DS18B20. It is good for meature the temperature and uploader to the server as a node. It supports 3.7 …