5pcs 3V/3.7V To 5V 1A Lithium Battery Step Up Module Board Mini Mobile Power Boost Charger Module with Undervoltage indication
$28.62
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Using high quality chips and expanding MOS tubes.
2. The output current is expanded to 1A, and the maximum output is 1.5A. The 2A Schottky diode is used to recharge the balance.
3. With the new scheme design, the circuit design does not require electrolytic capacitors and tantalum capacitors (the electrolytic capacitors have a short life and the tantalum capacitors are in danger of explosion). 3 ceramic capacitors (MCC) used in high-end circuits.
4. The same load indicator and undervoltage indication (when the battery voltage is less than 2.7V, the indicator will go out under load, when the battery voltage is greater than 2.7V with load, the indicator light is on, when there is no load, the indicator light is micro bright).
5. Ultra-small size, 14.1*18.8*5.5 mm.
6. The circuit conversion efficiency is high, the efficiency is higher than 90%, and the efficiency of the single-cell lithium battery is also less than 80%.
7. Input low power reverse connection protection. If your battery has 2A protection board, the protection board will protect when you input the positive and negative poles of the power supply. Note that when there is no protection board or the input current is greater than 2A, the input reverse connection protection Will fail, will cause the module to be damaged, remember.
8. Ultra-low quiescent current, new version, quiescent current will be less than 100 microamps. No connection is required to connect to the battery.
Specifications
Input voltage:1-5V
Output voltage:5.1-5.2V
Output current:rated 1A-1.5A (single-cell lithium battery input), maximum 1.5A (single-cell lithium battery input)
Conversion efficiency:up to 96% (the higher the input voltage, the higher the efficiency)
Switching frequency:500KHz
Output ripple:30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
Undervoltage indication:LED with load LED is on (input voltage is lower than 2.7V LED is off)
Operating temperature:industrial grade (-40 ° C to +85 ° C)
Full load temperature rise:30 ° C
Quiescent current:130uA
Load adjustment rate:±1%
Voltage regulation rate:±0.5%
Dynamic response speed:5% 200uS
Short circuit protection:None, if you want to have short circuit protection, you can input the lithium battery protection board or use a protected lithium battery.
Input reverse connection protection:none
Wiring method:welding
Input mode:IN+ input positive, IN- input negative
Applications
1).DIY a mobile power supply, you only need to input a battery power input, you can output 5V voltage to charge your mobile phone, MP3, MP4, PSP, very simple and convenient.
2). Power your electronic equipment. When your equipment needs 5V power supply, but now you only have lithium battery power supply, use this module to directly boost to 5V, solve your troubles.
3). The system is powered by the front stage. When you input the battery (1-5V) when you are working on a project, and your system board needs 5V stable power, then you choose this module will be your most. Good choice, you can work without commissioning directly on the machine, easily achieve high efficiency and high power boost.
Frequently Asked Questions and Answers
1. Why is my module designed to this shape
A:Our module is designed for your convenience. You can also remove the USB holder and solder the module directly to the PCB. The package is DIP-24.
2. How efficient is the module working I use it on the battery and it is very efficient. Can I use it
A:The efficiency of this module is very high in non-synchronous rectification. The highest efficiency of our test can reach 96%. There is also friends who do not blindly pursue high efficiency, high efficiency is proportional to the price, for example, you need 5V 0.5A power supply, 80% efficiency loss energy is 0.625W, 90% efficiency loss energy is 0.278W, Do you think it is necessary to double the cost of this 0.3W power It is ok to choose a combination.
3. Is this power module short-circuit protected When I use it, I accidentally output a short circuit and it will burn out
A:There is no short circuit protection. If you need short circuit protection, please connect the self-recovery fuse in series at the input.
4. Does this power module have input reverse connection protection When I use it, I accidentally input the power supply and it will burn out when I reverse it.
A:There is no reverse protection
5. Can this module current run at 5V 500mA for a long time
A:This module has a design power of 2.5W. It can run for a long time at 2.5W, and 5V*0.5A=2.5W can be operated for a long time. .
6. I need a current of about 2A. Can this module work in parallel
A:Direct parallel connection is not possible. There will be a large circulation between them. If you want to output parallel operation, you need to adjust the voltage of each module to a uniform error of less than 50 mV, so that it can work. Care should be taken to avoid overloading a single module and the output power should not exceed 70% of the total power of the module.
7. What is the working temperature of this module, can it reach the industrial level
A:Yes, the working temperature is -40 to 85 degrees.
Weight | 0.015 kg |
---|
Customers Also Viewed
Geekwrom HD 3.5 inch TFT Display Shield 800×480 for Raspberry Pi 3B 2B + Acrylic Matching Case Kit
$121.30Raspberry Pi & Orange PiAdd to cartGeekwrom HD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2B + Acrylic Matching Case KitHD 3.5 Inch TFT Display Shield 800×480 For Raspberry Pi 3B 2BFeatures– Demensions:85mm*56.5mm;– Resolution:800 x 480, 3.5 inch;– 267ppi High PPI display screen;– 11ms High Response Time(more than 60 fps);– 160° Wide Viewing Angle;– 900:1 High Contrast Ratio;– …
intelligent Screen Solar Pure Sine Wave Power inverter 1200W-6000W DC To AC 110V 120V Converter
$121.49InvertersAdd to cartWatt 1200W Voltage 12V Type Single digital display / Watt 2200W Voltage 12V Type Single digital display / Watt 3000W Voltage 12V Type Single digital display / Watt 3000W Voltage 24V Type Single digital display / Watt 3000W Voltage 48V Type Single digital displ
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable Heater
$48.59Solar CollectorsAdd to cartDescriptionMaterial:Stainless SteelColor:SilverPlug:US PlugVoltage:220-240V 50HzWattage:500WTemperature range:16-32°CCable Length:120cm/47.24inch(appr.)Heating Rod Length:41cm/16.14inch(appr.)FeaturesMade of stainless steel material, anti-rust, useful and durable.Double insulation & waterproof.Keep the water temperature steady.Suitable for aquarium:500L (for reference only).Simple adjustment and easy to read temperature indicator.Easy to install with 2 strong suckers (mounting distance of 2 suckers is about 9.5cm).Adjustment knob allows you to adjust the …
500W Aquarium Submersible Stainless Steel Heating Rod Adjustable HeaterRead More
5pcs JoyStick Module Shield 2.54mm 5 pin Biaxial Buttons Rocker for PS2 Joystick Game Controller Sensor
$14.30Other Module BoardAdd to cartFeaturejoystick joysticks standard interface module electronic building blocks and 2.54mm pin interface leads.Phillips is a two-way rocker 10K resistor, with the joystick in a different direction, tap the resistance vary. This module uses a 5V supply, the original state X, Y readout voltage of 2.5V or so, when pressed with the direction of the arrow, …
4Pcs Geekcreit Ultrasonic Module HC-SR04 Distance Measuring Ranging Transducers Sensor DC 5V 2-450cm
$9.83Sensor & Detector ModuleAdd to cartDescriptionWorking Voltage:5V(DC)Static Current:Less than 2mA.Output Signal:Electric frequency signal, high level 5V, low level 0V.Sensor Angle:Not more than 15 degrees.Detection Distance:2cm-450cm.High Precision:Up to 0.3cmInput Trigger Signal:10us TTL impulseSignal:output TTL PWL signalMode of connectionVCCtrig(T)ech0(R)GNDUse MethodSupply module with 5V, the output will be 5V while obstacle in range, or 0V if not.The out pin of this module is …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham Radio
$50.29RF amplifierAdd to cartApplicationBroadband RF power amplifier for all types of wireless applications, FM shortwave radios remote control toys, digital radio, etc., enter 1 milliwatt (0DBM) maximum output of 3 watts, 15V voltage supply, broadband work 1MHZ to 700MHZ can be work. As a result of well-designed, low end that can reach 35DBM (3W), at 500M, the output …
1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham RadioRead More
Reviews
There are no reviews yet.