5pcs 3V/3.7V To 5V 1A Lithium Battery Step Up Module Board Mini Mobile Power Boost Charger Module with Undervoltage indication
$28.62
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Using high quality chips and expanding MOS tubes.
2. The output current is expanded to 1A, and the maximum output is 1.5A. The 2A Schottky diode is used to recharge the balance.
3. With the new scheme design, the circuit design does not require electrolytic capacitors and tantalum capacitors (the electrolytic capacitors have a short life and the tantalum capacitors are in danger of explosion). 3 ceramic capacitors (MCC) used in high-end circuits.
4. The same load indicator and undervoltage indication (when the battery voltage is less than 2.7V, the indicator will go out under load, when the battery voltage is greater than 2.7V with load, the indicator light is on, when there is no load, the indicator light is micro bright).
5. Ultra-small size, 14.1*18.8*5.5 mm.
6. The circuit conversion efficiency is high, the efficiency is higher than 90%, and the efficiency of the single-cell lithium battery is also less than 80%.
7. Input low power reverse connection protection. If your battery has 2A protection board, the protection board will protect when you input the positive and negative poles of the power supply. Note that when there is no protection board or the input current is greater than 2A, the input reverse connection protection Will fail, will cause the module to be damaged, remember.
8. Ultra-low quiescent current, new version, quiescent current will be less than 100 microamps. No connection is required to connect to the battery.
Specifications
Input voltage:1-5V
Output voltage:5.1-5.2V
Output current:rated 1A-1.5A (single-cell lithium battery input), maximum 1.5A (single-cell lithium battery input)
Conversion efficiency:up to 96% (the higher the input voltage, the higher the efficiency)
Switching frequency:500KHz
Output ripple:30mV (MAX) 20M bandwidth (input 4V output 5.1V 1A)
Undervoltage indication:LED with load LED is on (input voltage is lower than 2.7V LED is off)
Operating temperature:industrial grade (-40 ° C to +85 ° C)
Full load temperature rise:30 ° C
Quiescent current:130uA
Load adjustment rate:±1%
Voltage regulation rate:±0.5%
Dynamic response speed:5% 200uS
Short circuit protection:None, if you want to have short circuit protection, you can input the lithium battery protection board or use a protected lithium battery.
Input reverse connection protection:none
Wiring method:welding
Input mode:IN+ input positive, IN- input negative
Applications
1).DIY a mobile power supply, you only need to input a battery power input, you can output 5V voltage to charge your mobile phone, MP3, MP4, PSP, very simple and convenient.
2). Power your electronic equipment. When your equipment needs 5V power supply, but now you only have lithium battery power supply, use this module to directly boost to 5V, solve your troubles.
3). The system is powered by the front stage. When you input the battery (1-5V) when you are working on a project, and your system board needs 5V stable power, then you choose this module will be your most. Good choice, you can work without commissioning directly on the machine, easily achieve high efficiency and high power boost.
Frequently Asked Questions and Answers
1. Why is my module designed to this shape
A:Our module is designed for your convenience. You can also remove the USB holder and solder the module directly to the PCB. The package is DIP-24.
2. How efficient is the module working I use it on the battery and it is very efficient. Can I use it
A:The efficiency of this module is very high in non-synchronous rectification. The highest efficiency of our test can reach 96%. There is also friends who do not blindly pursue high efficiency, high efficiency is proportional to the price, for example, you need 5V 0.5A power supply, 80% efficiency loss energy is 0.625W, 90% efficiency loss energy is 0.278W, Do you think it is necessary to double the cost of this 0.3W power It is ok to choose a combination.
3. Is this power module short-circuit protected When I use it, I accidentally output a short circuit and it will burn out
A:There is no short circuit protection. If you need short circuit protection, please connect the self-recovery fuse in series at the input.
4. Does this power module have input reverse connection protection When I use it, I accidentally input the power supply and it will burn out when I reverse it.
A:There is no reverse protection
5. Can this module current run at 5V 500mA for a long time
A:This module has a design power of 2.5W. It can run for a long time at 2.5W, and 5V*0.5A=2.5W can be operated for a long time. .
6. I need a current of about 2A. Can this module work in parallel
A:Direct parallel connection is not possible. There will be a large circulation between them. If you want to output parallel operation, you need to adjust the voltage of each module to a uniform error of less than 50 mV, so that it can work. Care should be taken to avoid overloading a single module and the output power should not exceed 70% of the total power of the module.
7. What is the working temperature of this module, can it reach the industrial level
A:Yes, the working temperature is -40 to 85 degrees.
Weight | 0.015 kg |
---|
Customers Also Viewed
5pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5V
$26.35Power Supply ModuleAdd to cartDescriptions3-Cell(3S) VersionInput voltage:DC 4.5V-5.5V(Recommend DC 5V)Charging voltage about:4.05V-5.1VCharging current about:230mA-240mAUSB power protectionShort circuit protection and zero volt battery activationBattery protectionOperating ambient temperature:-40° to +85°Storage temperature:-65° to +125°Size:30x 15 x 4mmNoteThe output voltage cannot be measured with a multimeter without a battery. But can be observed with an oscilloscope.Applicationskids toys carDigital CamerasSolar chargingBluetooth ApplicationsAudio equipmentDigital CameraElectronic …
5pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5VRead More
5Pcs/Pack 5V 1000mA 165*165mm Monocrystalline Solar Panel Cells with Positive&Negative Cables
$85.54Smart Robot & Solar PanelAdd to cartFeaturesProvide you with high conversion rate and incredibly efficient output.Excellent performance even under the weak sunlight.Portable and solid casing.Application:to charge, for home lighting and different kinds of low-power appliances, for science projects, for solar powered water pump, small solar power system, etc.SpecificationsType:Monocrystalline Size:165*165mmCurrent:1000mA Net Weight:about 600g one packPackage Content:5Pcs x Poly Solar PanelVoltage:5VMPN:Does Not ApplyPackage …
Waveshare 1.54 inch ink Screen Module 152×152 Electronic Paper SPI interface Yellow Black and White 3-color Display
$45.91Display ScreenAdd to cartDocumentsSchematic:Click here to openSample tutorial:Click here to openDatasheet:Click here to openGithub:Click here to openFeaturesNo backlight is needed, and the display content of the last screen can be kept for a long time after power offVery low power consumption, basically only consumes power when refreshingSPI control interface, can be connected to Raspberry/Nucleo and other main control …
Geekcreit DIY Creative Electronic Watch Kit 51 Single-chip LED Digital Tube Clock Training Production Kit
$15.30DIY Electronic KitsAdd to cartDescriptionName:LED Electronic Watch KitPower supply:CR2025 3V button battery (available for testing, there are inevitably extra factors causing insufficient power.)Display:LED red digital tube displaySize:52*52*18mmInstallation:the board need to solder yourself and then assembly the caseFunction:You can press the digital tube button when need to wacth time; it will enter the power saving mode automatically after 5 seconds. …
QFN32 QFP32 Converter SMD To DIP Adapter PCB Universal Board
$3.56Expansion Board & ShieldAdd to cartQFN32 QFP32 Converter SMD To DIP Adapter PCB Universal BoardSpecificationDimension:20.25 x 40.64mm / 0.79inch x 1.60inchThickness:1.5mmPanel:FR4DescriptionThe PCB board has two sides.A side for pin pitch size 0.80mm, B side for pin pitch size 0.80mm.It can be used to convert QFN32/QFP32 (600mil width, 2.54mm pin pitch).You can solder filter capacitors or resistors to increase stability and …
QFN32 QFP32 Converter SMD To DIP Adapter PCB Universal BoardRead More
YJ0007 180W Car Stereo Audio Amplifier Power Boost Board Single 12V input Conversion Double 32V Output
$52.41Boost & Buck ModuleAdd to cartDescriptionAll parts and components of this product are original products, unpretentious and pure in quality; using high-quality original parts not only guarantees safety and quality, but also has a long service life, and more importantly, it is a strong guarantee that the actual performance can reach the design goals.Features1. All components are genuine.2. The main …
Reviews
There are no reviews yet.