12V 2 Channel Relay Module with Optocoupler Support High Low Level Trigger
$8.73
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. The module uses genuine quality relay, normally open interfaces maximum load:AC 250V/10A, DC 30V/10A
2. Using SMD OPTOCOUPLER isolation, driving ability, stable performance; trigger current 5mA
3. The module voltage is 5V/9V/12 V/24V are available
4. The module can be set to high or low triggered by jumper
5. Fault-tolerant design, even if the control line is broken, the relay will not operate
6. The power indicator (green), relay status indicator (red)
7. Interface design humane, all interfaces can be connected directly via terminal wiring leads , very convenient
8. Module size:50mm * 40mm * 16mm (L * W * H)
9. Has four mounting bolts holes, hole 3.1mm
Interface
1. DC+:Positive power supply (voltage required by the relay, there 5V/9V/12V/24V choice )
2. DC-:Negative power connection
3. IN1:1 channel signal to trigger the end, you can set a high or low level control relay
3. IN2:2 channel signal to trigger the end, you can set a high or low level control relay
Outputs
NO1:After a relay normally open interfaces , relay before floating, shorted pull with COM1
COM1:1 relay common interface
NC1:1 relay normally closed port, COM1 relay shorted before and after the pull- vacant
NO2:2 -way normally open relay interface, the relay before floating, pull back and COM2 short
COM2:2 Common Interface relay
NC2:2 channel normally closed relay interface relay short front and COM2, pull vacant post
High and low trigger selection
S1 as a relay trigger selection of high and low
S2 high and low for the two -way relay trigger selection
Comes with low short circuit, triggering the corresponding relay is low, while the high end of the short com high trigger
High and low trigger selection
Short jumper with LOW triggered when connected
When the jumper is high with high short trigger
Package includes
1 x 12V 2 channel relay driver module for
Weight | 0.03 kg |
---|
Customers Also Viewed
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820io
$15.30Converter BoardAdd to cart>>>Manual:Click here to openOverviewUSR-ES1 embeds Wiznet’s W5500 chip, which uses hardware logic gates to implement the transport layer and network layer of the TCP/IP protocol stack (such as TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE, etc.), and integrates The data link layer, physical layer, and 32K bytes of on-chip RAM serve as data transceiving buffers. …
USR-ES1 W5500 Chip SPI to LAN Ethernet Converter TCP/IP Module WIZ820ioRead More
3pcs TEC1-12715 12V Heat Sink thermoelectric Cooler Peltier Plate Module
$32.04Electronic Accessories & SuppliesAdd to cart40 x 40mm TEC1-12715 12V Heatsink Thermoelectric Cooler Peltier Plate ModuleDescriptionSolid state, vibration free, noise-freeSimple to install and operateThe hot surface need to be good heat sinkSpecificationProduct name:thermoelectric cooler plate moduleModel:TEC1-12715Color:whiteCouples:127Voltage:12VUmax:15.4VImax:15AMax power consumption:231WTmax:70°CQcmax T=0(W):137WSize:40 x 40 x 3.3mmWeight:50gPackage included3 x TEC1-12715 cooler plate module
EQKIT KM-1 DC 6-12V PWM Motor Speed Controller Kit DIY Motor Speed Regulator Set Stepless Speed Control
$8.73Module KitsAdd to cartSpecificationsModel:KM-1Operating voltage:DC 6-12VPCB board size:40 x 40mmCircuit descriptionKM-1 uses PWM (pulse width modulation) to control the speed of the motor, adjust the pulse width duty ratio, so that the speed from zero to the maximum speed stepless speed regulation. The wider the crest width of the control waveform, the faster the motor speed; on the …
20pcs 63V 10000UF 105 High Frequency Temp Electrolytic Capacitor 30mm x 50mm Long Life
$108.62Electronic Accessories & SuppliesAdd to cartSpecificationModel:485622Voltage:63VCapacitance:10000UFTemperature:105→Diameter:30mm / 1.1 inchHeight:50 mm / 2 inchFeaturesLong life, high temperatureHigh-frequency capacitorsPackage included20 x Electrolytic Capacitor
Reviews
There are no reviews yet.