HC-SR501 Adjustable infrared IR Pyroelectric PIR Module Motion Sensor Human Body induction Detector with Bracket
$6.55
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Features
1. Automatic induction:When someone enters its induction limits, enter the high level, people leave the sensor range is automatically delayed off high. Output low.
2. photosensitive control (optional):the module reserved for location, can be set to photosensitive control, strong light during the day or not induction. Photosensitive control is optional, the factory did not install the photosensitive resistor. If necessary, please buy a separate photosensitive resistor to install.
3. Two trigger modes:L is not repeatable, H is repeatable. Can be jumper selected, the default is H.
A. non-repeatable trigger mode:the induction output high, the delay time is over, the output will automatically change from high to low.
B. Repeated trigger mode:that is, after sensing the output high, in the delay time period, if the human body in its sensing limits of activities, its output will remain high until the delay after the person will leave the high The level changes to low level (the sensing module automatically delays a delay time after every activity of the human body, and takes the time of the last activity as the starting point of the delay time).
4. Induction blocking time (default setting:3-4 seconds):After each sensing output (high level goes low), the sensing module can be followed by a blocking time, during which it is sensed The device does not receive any sense signals. This function can be used to achieve the interval between the sensing output time and the blocking time. It can be applied to the interval detection products. At the same time, this function can effectively suppress all kinds of interference in the process of load switching.
5. Wide operating voltage:the default operating voltage DC5V to 20V.
6. Micro-power:Quiescent current 65 microamps, especially for dry battery-powered electrical products.
7. Output high-level signal:can be easily with various types of circuits to achieve docking.
Instructions for use
1. Induction module power about one minute after the initialization time, at this time the module will output 0-3 times a minute, a minute into the standby state.
2. Light and other interference should be avoided Directly close the surface of the lens module, so as not to introduce interference with the signal to produce malfunction; use of the environment as far as possible to avoid
Free flow of wind, the wind will cause interference to the sensor.
3. Sensor module with dual-element probe, the probe window is rectangular, dual element (A yuan B yuan) in the longer direction at both ends, when the body from left to right
Or from right to left through the infrared spectrum to the dual time, distance difference, the greater the difference, the more sensitive induction, when the body from the front to the probe
Head or from top to bottom or from bottom to top direction, the dual element can not detect infrared spectral distance changes, no difference, so the sensor insensitive or does not work; so the sensor should be installed so that the direction of the probe dual And the direction of human activity as much as possible parallel to ensure that the body has been through
Probe dual-element induction. In order to increase the sensing angle limits, this module uses a circular lens, also makes the probe four sides are sensitive, but the left and right sides are still
However, compared with the upper and lower direction of the two induction limits, sensitivity, installation must still try to according to the above requirements.
Use should pay attention to the following points
1. The DC voltage must meet our requirements, too high and too low will affect the performance of the module, but also requires the power supply must be a good regulator filter, such as computer USB power, mobile phone charger power supply, the old 9V stacked battery Are unable to meet the module work requirements, it is recommended that customers use the power transformer and the regulator through the three-terminal voltage regulator and then through the 220UF and 0.1UF capacitor filter power supply.
2. Although the human body is not in front of the module, but the human body from the module is too close to the module can also be caused by the sensor output, as well as debugging the human body do not touch the circuit part will also affect the module work , A more scientific approach is to output a LED or a multimeter, the module covered with a newspaper, when someone leaves room, wait 2 minutes and see if the module still has output.
3. The module does not take the load to work properly, connected to the load after the work of chaos, one reason is because the power capacity is very small load power consumption, load caused by voltage fluctuations caused by the module malfunction, the other reason is the load The power will have interference in the work, such as relays or electromagnets and another inductive load will produce a reverse electromotive force, 315M emission plate will have electromagnetic radiation and other work will affect the module. The solution is as follows:A, the power part of the inductor filter. B, using the load and the module using different voltage methods, such as:load using 24V operating voltage, the module uses 12V operating voltage, during which the use of three-terminal regulator isolation. C:Use a larger capacity power supply.
4. The human body sensor module can only work indoors and the work environment should avoid the sun, a strong direct light exposure, if the work environment has a strong RF interference, you can use shielding measures. Because of the strong air interference, close the doors and windows or prevent convection. The induction area to avoid facing heating appliances and objects as well as easy to wind debris and clothing.
5. The human body sensor module is recommended to install in a sealed box, otherwise, there may have been the output signal.
6. If the body sensor module detection angle is less than 90 degrees, you can use opaque adhesive tape to cut off the lens or cut lens to achieve.
7. The human body sensor module with dual-element probe, the body’s hands and feet and head movement direction and the sensitivity of the sensor are closely linked, and the infrared module determines the characteristics of the sensor can not accurately control the distance.
8. The module of the probe (PIR) can be mounted on the other side of the circuit board. The probe can also be extended with a two-core shielded cable, the length should be less than 20 cm as well.
Package includes
1 x HC-SR501 Motion Sensor
1 x Bracket
Weight | 0.016 kg |
---|
Customers Also Viewed
WEAH-307 3 Way Audio Speaker Crossover 100W Filter Treble Mediant Bass Frequency Divider Module
$15.30Amplifier BoardAdd to cartFeatureMode:WEAH-307Power:100WImpedance:4-8ohmCompatible for:Under 6inches HornTreble Standard:12db/octBass Standard:12db/octSize:8.5×6.2×2.6cmFrequency response:low 45Hz, high 20KHzPackage includes1 x 100W Filter Treble Mediant Bass Frequency Divider
3pcs WXD3-13-2W Precision Potentiometer 22K 22K Ohm Wirewound Multi-Turn Potentiometer
$10.49Module ComponentsAdd to cartSpecificationsResistance range:22K┯Resistance tolerance:÷ 5%Rotation angle:3600 ÷ 20 Number of laps:10 lapsRated voltage:160VStarting torque:3.5 ~ 100mN.mRated power:2W (85 →) 0W (125 →)Linearity accuracy:÷ 0.3%Mechanical durability:10,000 weeksPackage included3 x Potentiometer
20Pcs Serial Port WIFI ESP8266 Module Adapter Plate with IO Lead Out for ESP-07 ESP-08 ESP-12
$12.02Smart ModuleAdd to cart20Pcs Serial Port WIFI ESP8266 Module Adapter Plate With IO Lead Out For ESP-07 ESP-08 ESP-12This Adapter Plate is for ESP-07 ESP-08 ESP-12, a test board with IO lead out.NoteNeed to solder 3V regulator by youself.ESP-07, ESP-08, ESP-12 module board are not included!!!Package included20 x Serial Port WIFI ESP8266 Module Adapter Plate40 x Pins
10pcs 2S 5A Li-ion Lithium Battery 7.4V 8.4V 18650 Charger Protection Board BMS for Li-ion Lipo Battery
$16.88Battery Protection ModuleAdd to cartSpecificationsModel:HX-2S-A2 Overcharge voltage range:4.25-4.35v ± 0.05vSize:17.5 * 17.5 * 3.2mm over discharge voltage range:2.5-3.0v ± 0.05vUpper limit operating current:5A Operating temperature:-40 — +50 °Upper limit instantaneous current:7A Storage conditions:-40– +80 °Quiescent current:less than 10uA Effective life:more than 50,000 hoursInternal resistance:less than 300mΩ Short circuit protection:can be protected, need to charge recoveryCharging voltage:8.4V-9VWelding point DescriptionB + …
DC 24V 600L/H Submersible Pump Immersible Pump Under Water Pump Bath Pump
$42.51Electrical Pump & ValveAdd to cartSubmersible Pump Immersible Pump Under Water Aquarium Bath Pump DC 24V 600L/HSpecificationColor:GreyUse:SubmersibleMaterial:Engineering ABSRated Voltage:DC 24VStarting Voltage:6VCurrent:0.75AFlow:600L/HNoise:50dB MAXMax. Head:500cmPower:18wWaterproof grade:IP68Motor:brush motorWater temperature:-20 ° C ~ 60 ° ° CAmbient humidity:45%~90%No load current:less than 0.2ACurrent at load:1.2ACable:1.5m /59.06inch(appr.)Total Length:105.9mm /4.31inch(appr.)FeaturesBrand New and high quality.Suitable for tap water, sea water, ground waterCannot be used directly with 220V AC …
DC 24V 600L/H Submersible Pump Immersible Pump Under Water Pump Bath PumpRead More
TDA7498 2.1 Digital Power Amplifier Board 200W+100W+100W Supasses TPA3116 Class D DC24V
$70.06Amplifier BoardAdd to cartFeatures-Using original TDA7498 TL072-The front input capacitor and the inter-stage coupling capacitor use Siemens’ top-level capacitors 1UF, the electrolytic capacitor signal main circuit uses Taiwanese famous brands, and the main filter capacitor uses special electrolytic capacitors 2≠2200UF to ensure strong continuous power support.-The resistors are high-precision chip resistors, and the main circuit uses five-ring metal …
TDA7498 2.1 Digital Power Amplifier Board 200W+100W+100W Supasses TPA3116 Class D DC24VRead More
3Pcs RobotDyn RTC DS1307 Real Time Clock Battery Shield with Pin Headers Set
$18.67Expansion Board & ShieldAdd to cartPINOUT:http://img.staticbg.com/file/products/20171226001032PINOUT-RTCDS1307.pdfSchematic:http://img.staticbg.com/file/products/20171226001140Schematic-RTCDS1307.pdfFeatureType:Logic ICsPackage includes3 x RTC DS1307 (real time clock) + battery3 x Wemos D1 mini shield6 x Male Pin Header 8pins6 x Female Pin Header -BLACK 8pins6 x Stackable Header – BLACK 8pins
Reviews
There are no reviews yet.