ZB206 V1.3 Battery Capacity Tester internal Resistance Test 18650 Lithium Battery Tester
$24.04
Voltage 5V / Voltage 12V /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Feature
Supply voltage:DC12V / 5V (optional)
Working current
Maximum battery input voltage:8.5V
Maximum error of discharge current:1%+2mA
Voltage measurement error:1%-3D
The maximum error of the overall measurement results:0.1-0.2A 2.5%, 0.3-0.5A 1.6%, 0.6-1.0A 1.2%, 1.1A-2.6A 1%
Circuit board size (no copper feet):97 x 62 x 38mm
Weight (with copper feet):47g
Instruction:Click to open
Quick start instructions (factory default)
1. Full charged the test battery (or power bank), positive and negative electrodes are respectively connected to the blue terminal of the bat+ and bat-, the connection line is recommended as far as possible short and thick! using DC 12V operating voltage, power on the test instrument display discharge current.
2. Press the S — or S++ button can change the setting current within 0.1-2.6A, when the current is correct, press SK button to start test (such as fault code Err* please refer to the following content), the tester can intelligent selection of cell types and formulate termination voltage, start testing “RUN Inch indicator lights, digital tube display values from ah capacity, energy wh, voltage V and A current take turns display. When the test is completed, the digital tube stays in the Ah fast flashing with a voice reminder, “RUN Inch indicator lights off.
3. After the completion can press the “SK Inch button to make the tester stop flashing alarm, you can also press the S — or S++ button switch check battery capacity Ah, energy Wh and discharge plateau voltage V, when pressed “SK Inch button again, tester returned to the startup current of the setting state, can be repeated previous operation to next battery test.
Note:during test alarm state, must be carried out one key operation, the backup data will be cleared, if not doing one button operation, the backup will always save the results, even if the power is cut off!
The meaning and processing method of error code Err*
Err1:the battery voltage is too high, please confirm that the battery voltage is lower than 8.5V before test.
Err2:the battery voltage is too low (below the set value of the termination voltage), please confirm the battery voltage and reset. If the battery is connected reversed and the four wire mode voltage measurement is not connected or connected to the reverse is also display Err2.
Err3:the battery does not support setting discharge current or circuit resistance is too high, please use a smaller current to test battery, and to ensure that the cell line is thick and short, between the electrode contact is good.
Err4:power tube damage, the problem generally occurs after the bad transformation, can replace the power tube, substitute models have P75NF75, etc..
Err5:beyond the test power constraints! this status is only possible when the power limit function is turned on (LPon), under on behalf of the set conditions the discharge power is more than 12W, the tester to prevent heat overheating and take protective measures. Users can DIY yourself (to increase the heat sink or installation of fans), and enter the function setting menu to close the power limit (LPoF), now you can use more than 12W power.
Err6:the power supply voltage is out of range, when the power supply voltage is lower than 11V or higher than 14V, the test instrument under booting will show the error code, please replace the appropriate voltage power supply!!
Note:when display the Err1-Err5, press any key to return to the initial state.
Package includes
1 x Lithium Battery Tester (Test tools does not includes)
Weight | 0.02 kg |
---|
Customers Also Viewed
5pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5V
$26.35Power Supply ModuleAdd to cartDescriptions3-Cell(3S) VersionInput voltage:DC 4.5V-5.5V(Recommend DC 5V)Charging voltage about:4.05V-5.1VCharging current about:230mA-240mAUSB power protectionShort circuit protection and zero volt battery activationBattery protectionOperating ambient temperature:-40° to +85°Storage temperature:-65° to +125°Size:30x 15 x 4mmNoteThe output voltage cannot be measured with a multimeter without a battery. But can be observed with an oscilloscope.Applicationskids toys carDigital CamerasSolar chargingBluetooth ApplicationsAudio equipmentDigital CameraElectronic …
5pcs 3S NiMH NiCd Rechargeable Battery Charger Charging Module Board input DC 5VRead More
5Pcs/Pack 5V 1000mA 165*165mm Monocrystalline Solar Panel Cells with Positive&Negative Cables
$85.54Smart Robot & Solar PanelAdd to cartFeaturesProvide you with high conversion rate and incredibly efficient output.Excellent performance even under the weak sunlight.Portable and solid casing.Application:to charge, for home lighting and different kinds of low-power appliances, for science projects, for solar powered water pump, small solar power system, etc.SpecificationsType:Monocrystalline Size:165*165mmCurrent:1000mA Net Weight:about 600g one packPackage Content:5Pcs x Poly Solar PanelVoltage:5VMPN:Does Not ApplyPackage …
Waveshare 1.54 inch ink Screen Module 152×152 Electronic Paper SPI interface Yellow Black and White 3-color Display
$45.91Display ScreenAdd to cartDocumentsSchematic:Click here to openSample tutorial:Click here to openDatasheet:Click here to openGithub:Click here to openFeaturesNo backlight is needed, and the display content of the last screen can be kept for a long time after power offVery low power consumption, basically only consumes power when refreshingSPI control interface, can be connected to Raspberry/Nucleo and other main control …
Geekcreit DIY Creative Electronic Watch Kit 51 Single-chip LED Digital Tube Clock Training Production Kit
$15.30DIY Electronic KitsAdd to cartDescriptionName:LED Electronic Watch KitPower supply:CR2025 3V button battery (available for testing, there are inevitably extra factors causing insufficient power.)Display:LED red digital tube displaySize:52*52*18mmInstallation:the board need to solder yourself and then assembly the caseFunction:You can press the digital tube button when need to wacth time; it will enter the power saving mode automatically after 5 seconds. …
QFN32 QFP32 Converter SMD To DIP Adapter PCB Universal Board
$3.56Expansion Board & ShieldAdd to cartQFN32 QFP32 Converter SMD To DIP Adapter PCB Universal BoardSpecificationDimension:20.25 x 40.64mm / 0.79inch x 1.60inchThickness:1.5mmPanel:FR4DescriptionThe PCB board has two sides.A side for pin pitch size 0.80mm, B side for pin pitch size 0.80mm.It can be used to convert QFN32/QFP32 (600mil width, 2.54mm pin pitch).You can solder filter capacitors or resistors to increase stability and …
QFN32 QFP32 Converter SMD To DIP Adapter PCB Universal BoardRead More
YJ0007 180W Car Stereo Audio Amplifier Power Boost Board Single 12V input Conversion Double 32V Output
$52.41Boost & Buck ModuleAdd to cartDescriptionAll parts and components of this product are original products, unpretentious and pure in quality; using high-quality original parts not only guarantees safety and quality, but also has a long service life, and more importantly, it is a strong guarantee that the actual performance can reach the design goals.Features1. All components are genuine.2. The main …
Reviews
There are no reviews yet.