ZB206 V1.3 Battery Capacity Tester internal Resistance Test 18650 Lithium Battery Tester
$24.04
Voltage 5V / Voltage 12V /
Shipping:Standard Shipping about 10-25 business days
Secure Payment:Paypal,VISA,MasterCard
Feature
Supply voltage:DC12V / 5V (optional)
Working current
Maximum battery input voltage:8.5V
Maximum error of discharge current:1%+2mA
Voltage measurement error:1%-3D
The maximum error of the overall measurement results:0.1-0.2A 2.5%, 0.3-0.5A 1.6%, 0.6-1.0A 1.2%, 1.1A-2.6A 1%
Circuit board size (no copper feet):97 x 62 x 38mm
Weight (with copper feet):47g
Instruction:Click to open
Quick start instructions (factory default)
1. Full charged the test battery (or power bank), positive and negative electrodes are respectively connected to the blue terminal of the bat+ and bat-, the connection line is recommended as far as possible short and thick! using DC 12V operating voltage, power on the test instrument display discharge current.
2. Press the S — or S++ button can change the setting current within 0.1-2.6A, when the current is correct, press SK button to start test (such as fault code Err* please refer to the following content), the tester can intelligent selection of cell types and formulate termination voltage, start testing “RUN Inch indicator lights, digital tube display values from ah capacity, energy wh, voltage V and A current take turns display. When the test is completed, the digital tube stays in the Ah fast flashing with a voice reminder, “RUN Inch indicator lights off.
3. After the completion can press the “SK Inch button to make the tester stop flashing alarm, you can also press the S — or S++ button switch check battery capacity Ah, energy Wh and discharge plateau voltage V, when pressed “SK Inch button again, tester returned to the startup current of the setting state, can be repeated previous operation to next battery test.
Note:during test alarm state, must be carried out one key operation, the backup data will be cleared, if not doing one button operation, the backup will always save the results, even if the power is cut off!
The meaning and processing method of error code Err*
Err1:the battery voltage is too high, please confirm that the battery voltage is lower than 8.5V before test.
Err2:the battery voltage is too low (below the set value of the termination voltage), please confirm the battery voltage and reset. If the battery is connected reversed and the four wire mode voltage measurement is not connected or connected to the reverse is also display Err2.
Err3:the battery does not support setting discharge current or circuit resistance is too high, please use a smaller current to test battery, and to ensure that the cell line is thick and short, between the electrode contact is good.
Err4:power tube damage, the problem generally occurs after the bad transformation, can replace the power tube, substitute models have P75NF75, etc..
Err5:beyond the test power constraints! this status is only possible when the power limit function is turned on (LPon), under on behalf of the set conditions the discharge power is more than 12W, the tester to prevent heat overheating and take protective measures. Users can DIY yourself (to increase the heat sink or installation of fans), and enter the function setting menu to close the power limit (LPoF), now you can use more than 12W power.
Err6:the power supply voltage is out of range, when the power supply voltage is lower than 11V or higher than 14V, the test instrument under booting will show the error code, please replace the appropriate voltage power supply!!
Note:when display the Err1-Err5, press any key to return to the initial state.
Package includes
1 x Lithium Battery Tester (Test tools does not includes)
Weight | 0.02 kg |
---|
Customers Also Viewed
300W Digital Amplifier Speaker Protection Board 2.1 Channel Relay Speaker Protection Module Boot Delay DC Protection
$15.30Relay ModuleAdd to cartFeatures1.With delay and DC protection (default 1.8V control, DC sensitivity can be adjusted)2. This common power DC protection board uses an optocoupler. Since the optocoupler has input and output isolation,3. Electrical signal transmission has the characteristics of unidirectionality, so it has good electrical insulation and anti-interference ability.4. Since the input end of the optocoupler belongs …
AB18 2SA1943/2SC5200 High Power 300W + 300W Dual Channel Class A/B Power Amplifier Board for Sound Speaker DIY
$125.17Amplifier BoardAdd to cartProduct description1. Using Japan imported original brand new 2SA1943/2SC52002. Electrolytic capacitor adopts imported electrolysis to ensure strong continuous power support.3. The resistor uses high-precision resistors, and the main circuit uses high-precision resistors with an accuracy of ÷ 1% to ensure a good signal-to-noise ratio for the whole machine.4. The PCB adopts 1.6mm thick double-sided sheet, …
5pcs DMP-L1 WiFi intelligent Lighting Module Built-in ESP ESP8285 WiFi Chip for Smart Home
$28.82Smart ModuleAdd to cartDescriptionThe core processor of DMP-L1 module adopts industrial chip ESP8285. The chip integrates an enhanced version of the Tensilica’s L106 Diamond Series 32-bit core processor in smaller size packages. ESP8285 has a complete Wi-Fi network function, which can be used independently from the controller. Its built-in cache memory greatly provides CPU performance.DMP-L1 module supports standard …
5pcs DMP-L1 WiFi intelligent Lighting Module Built-in ESP ESP8285 WiFi Chip for Smart HomeRead More
Wareshare 5.5 inch AMOLED HDMI Display Capacitive Touch Screen with Tempered Glass Support for NVIDIA Jetson Nano Raspberry Pi
$229.66Display ScreenAdd to cartDocumentsManual:Click here to openDatasheet:Click here to openSoftwarePanasoni SDFormatterWin32DiskImagerPuTTYOverviewThis product is a universal 5.5-inch HDMI display with 1080≠1920 ultra-clear resolution and a capacitive touch panel. Support for Raspberry Pi and various mini PCs, also as a computer monitor.Features5.5inch AMOLED, 1080×1920 resolution.Toughened glass capacitive touch panel.Supports popular mini PCs such as Raspberry Pi, as well as general …
5pcs 20x20x15mm DIY CPU IC Chip Heat Sink Extruded Cooler Aluminum Heat Sink
$4.36Electronic Accessories & SuppliesAdd to cartFeatureAluminum heat sinks for electronics, computers, electrical facilities, play a cooling effectSpecificationMaterials:AluminumSize:20*20*15mm (L*W*H)Color:SilverQty:5pcsPackage includes5 x CPU IC Chip Aluminum Heat Sink
5Pcs Yellow Backlight 1602 Character LCD Display Module
$24.89Display ScreenAdd to cartDescriptionLCD display module with yellow backlightWide viewing angle and high contrastBuilt-in industry standard HD44780 equivalent LCD controllerCommonly used in:copiers, fax machines, laser printers, industrial test equipment,networking equipment such as routers and storage devicesLCM type:CharactersCan display 2-lines X 16-charactersOperate with 5V DCModule dimension:80mm x 36mm x 12mmViewing area size:64.5mm x 16mmPackage included5 X LCD display module
Bathtub Caddy Bamboo Bath Tub Holder Bathroom Tray Glass Book Reading Rack Stand
$106.76FoamAdd to cartSpecificationMaterial:BambooColor:WoodSize:(L)X(W)X(H)105X22X4cm/41.34inchX8.66inchX1.57inch(appr.)Features1. Constructed from durable bamboo and metal supporting frame in excellent craftsmanship for many years use.2. Varnish processing on surface, lightweight and easy to operate.3. Books can be held with metal rack stably for reading when bathing.4. Books, phone, towl, and food can be placed on it for convenient reach.5. Its length is adjustable between …
Bathtub Caddy Bamboo Bath Tub Holder Bathroom Tray Glass Book Reading Rack StandRead More
Reviews
There are no reviews yet.